Inhaltszusammenfassung zur Seite Nr. 1
CD RECEIVER KD-LH1150/KD-LH1100
RECEPTOR CON CD KD-LH1150/KD-LH1100
RECEPTEUR CD KD-LH1150/KD-LH1100
ATT SOUND
U
R SOURCE F
D
VOL VOL
• This unit is equipped with the display demonstration. To cancel it, see page 8.
• Esta unidad está equipada con demostración en la pantalla. Para cancelarla, consulte la página 8.
• Cet appareil est équipé d’une fonction de démonstration des affichages. Pour l’annuler, référez-vous
à la page 8.
For installation and connections, refer to the separate manual.
Para
Inhaltszusammenfassung zur Seite Nr. 2
INFORMATION (For U.S.A.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guara
Inhaltszusammenfassung zur Seite Nr. 3
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. CONTENTS How to reset your unit ............................... 2 OTHER MAIN FUNCTIONS ................ 24 Changing the general settings (PSM) ....... 24 LOCATION OF THE BUTTONS ............ 4 Selecting the dimmer mode ...................... 28 Control panel............................................. 4
Inhaltszusammenfassung zur Seite Nr. 4
LOCATION OF THE BUTTONS Control panel 1 2 3 4 5 678 9 p q w e r ty u 1 (standby/on/attenuator) button p SEL (select) button 2 EQ (equalizer) button q D (DISP: display) button 3 Control dial w Number buttons 4 Display window e M (MODE) button 5 FM/AM button r Remote sensor 65 (up) button t CD/CD-CH (CD changer) button 70 (eject) button y∞ (down) button 84 /¢ buttons u Trim illumination 9 (control panel release) button Illumination Navigation for easy operations: If you press M (MODE), EQ (equali
Inhaltszusammenfassung zur Seite Nr. 5
3 • Selects the preset stations while listening to Remote controller the radio. Each time you press the button, the preset station number increases, and the selected station is tuned in. ATT SOUND • While playing an MP3 disc on an MP3- compatible CD changer; – Skips to the previous disc if pressed briefly. – Skips to the previous folder if pressed and U held. SOURCE F R Note: While playing a CD on a CD changer, this always skips to the previous disc. D 4 Functions the same as the control dial on
Inhaltszusammenfassung zur Seite Nr. 6
3. Return the battery holder. Preparing the remote controller Insert again the battery holder by pushing it until you hear a clicking sound. Before using the remote controller: • Aim the remote controller directly at the remote sensor on the main unit. Make sure there is no obstacle in between. (back side) WARNING: Remote sensor • Store the battery in a place where children cannot reach. • Do not expose the remote sensor to strong If a child accidentally swallows the battery, light (direct sunli
Inhaltszusammenfassung zur Seite Nr. 7
BASIC OPERATIONS 1 3 2 Turning on the power 4 Adjust the sound as you want. (See pages 20 – 22.) 1 Turn on the power. Note: While playing a source, you can also show the level meter on the display. For details, see “Activating the Note on One-Touch Operation: level meter” on page 23. When you select a source in step 2 below, the power automatically comes on. You do not have To drop the volume in a moment to press this button to turn on the power. Press briefly while listening to any source. “AT
Inhaltszusammenfassung zur Seite Nr. 8
Canceling the display 3 Select “Off.” demonstration When shipped from the factory, display All Demo Int Demo demonstration has been activated, and starts Off automatically when no operations are done for about 20 seconds. • It is recommended to cancel the demonstration before you use the unit for the first time. 4 Finish the setting. To cancel the display demonstration, follow the procedure below: 1 Press and hold SEL (select) for more To activate the display demonstration, repeat than 2 seconds
Inhaltszusammenfassung zur Seite Nr. 9
Setting the clock 4 Set the minute. 1 Select “Clock Min” (minute). You can also set the clock system to either 2 Adjust the minute. 24 hours or 12 hours. 12 1 Press and hold SEL (select) for more than 2 seconds so that one of the PSM items appears on the display. (PSM: see pages 24 and 25.) The next-step-operation buttons start flashing. 5 Set the clock system. 1 Select “24H/12H.” 2 Select “24Hours” or “12Hours.” 2 Press number button 2 to select 12 “CLOCK”—Clock category of the PSM settings. Th
Inhaltszusammenfassung zur Seite Nr. 10
RADIO OPERATIONS To stop searching before a station is received, Listening to the radio press the same button you have pressed for searching. You can use either automatic searching or manual searching to tune in to a particular station. Searching a station manually: Manual search Searching a station automatically: Auto search 1 Select the band (FM1 – 3, AM). Each time you press the 1 Select the band (FM1 – 3, AM). button, the band changes as Each time you press the follows: button, the band chan
Inhaltszusammenfassung zur Seite Nr. 11
If the sound quality decreases and the 3 Tune in to a station you want while stereo effect is lost while listening to an “Manual Search” is flashing. FM station To tune in to stations In some areas, adjacent stations may of higher frequencies interfere with each other. If this interference occurs, this unit can automatically reduce this interference noise (the initial setting when shipped from the factory). However, in this To tune in to stations of lower frequencies case, the sound quality will
Inhaltszusammenfassung zur Seite Nr. 12
2 Start automatic preset. 2 Tune in to a station (in this example, 1 Press M (MODE). of 88.3 MHz). “Mode” appears on the display. To tune in to stations The next-step-operation of higher frequencies buttons start flashing. 2 Press and hold number button 5, while “Mode” is still on the display. To tune in to stations of lower frequencies 3 Press and hold the number button (in this example, 1) for more than 2 seconds. “–SSM–” appears, then disappears when automatic preset is over. Local FM station
Inhaltszusammenfassung zur Seite Nr. 13
Selecting a preset station using the Tuning in to a preset station preset station list You can easily tune in to a preset station. If you forget what stations are stored in what Remember that you must store stations first. If preset numbers, you can check the preset station you have not stored them yet, see “Storing list, then select your desired station. stations in memory” on pages 11 and 12. 1 Select the band (FM1 – 3, AM). Selecting a preset station directly Each time you press the button, t
Inhaltszusammenfassung zur Seite Nr. 14
Changing the display pattern By pressing D (DISP), you can change the information shown on the display. Each time you press the button, the display patterns change as follows: Small animation Large animation display display 1 Current sound Clock time mode (iEQ) (see page 21) Small animation Clock time display display 2 If a name has been assigned to a station it will be shown instead of “NO NAME.” 14 EN10-14KD-LH1150_1100[J]f.p65 14 1/25/03, 11:17 AM ENGLISH
Inhaltszusammenfassung zur Seite Nr. 15
CD OPERATIONS The display changes to show the following: Playing a CD 1 Open the control panel. Total track number and total playing time of the inserted disc Note on One-Touch Operation: When a CD is already in the loading slot, pressing CD/CD-CH turns on the unit and starts playback automatically. 2 Insert a CD into the loading slot. Current track and elapsed playing time The unit turns on, draws the CD and Notes: starts playback • When a CD is inserted upside down, the CD automatically. autom
Inhaltszusammenfassung zur Seite Nr. 16
To stop play and eject the CD To go to a particular track directly Press 0. Press the number button corresponding to the CD play stops and the control panel flips down. track number to start its playback. The CD automatically ejects from the loading slot. The source changes to the previously selected source. • If you change the source, CD play also stops (without ejecting the CD). Next time you select “CD” as the source, CD • To select a track number from 1 – 6: play starts from where playback h
Inhaltszusammenfassung zur Seite Nr. 17
To play back tracks repeatedly How to go to the desired track quickly (Track Repeat Play) • Ex. 1: To select track number 32 while You can play back the current track repeatedly. playing track number 6 1 Press M (MODE) while playing a CD. “Mode” appears on the display. The next-step-operation buttons start flashing. (Three times) (Twice) Track 6 \ 10 \ 20 \ 30 \ 31 \ 32 2 Press number button 2, while “Mode” is still on • Ex. 2 :To select track number 8 while the display. playing track number 36
Inhaltszusammenfassung zur Seite Nr. 18
To play back only intros (Track Intro Scan) Prohibiting CD ejection You can play back the first 15 seconds of each You can prohibit CD ejection and can lock a CD track sequentially. in the loading slot. 1 Press M (MODE) while playing a CD. “Mode” appears on the display. While pressing CD/CD-CH, press and The next-step-operation buttons hold for more than 2 seconds. start flashing. 2 Press number button 1, while “Mode” is still on the display. Each time you press the button, “Intro Track” or “In
Inhaltszusammenfassung zur Seite Nr. 19
Changing the display pattern By pressing D (DISP), you can change the information shown on the display. Each time you press the button, the display patterns change as follows: Large animation display Small animation display 1 Current sound Clock time Small animation mode (iEQ) display 2 (see page 21) Small animation display 3 Clock time Small animation display display 4 Notes: • When the disc title/performer is shown, the (disc) indicator lights up. When the track title is shown, the (track) i
Inhaltszusammenfassung zur Seite Nr. 20
SOUND ADJUSTMENTS 1 * If you are using a two-speaker system, set the fader Adjusting the sound level to “00.” 2 * Only for KD-LH1150: You can adjust the sound characteristics to your This takes effect only when a subwoofer is preference. connected. • “Vol Adj” setting is required for each source 3 * By adjusting the input level to match it to the FM except FM. Before starting “Vol Adj,” select an sound level, you will not need to adjust the volume appropriate source for which you want to make le
