Inhaltszusammenfassung zur Seite Nr. 1
Installation Manual
RANGE HOOD
MODEL: BUF-03R
TABLE OF CONTENTS
Safety Instructions .................................................................................................. 2
Name of Parts ......................................................................................................... 4
Size & Dimensions .................................................................................................. 4
Range Hood Location ......................................................
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY INSTRUCTIONS aaaaaaaaaaaa aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa Before installation and operation, read these instructions carefully and use this product only in the manner described by the manufacturer in the operation manual. The instruction shown below are used to alert you to potential personal injury and property damage hazards. There are three hazard classifications based on potentially dangerous situations. Obey all safety instructions that show these symbols to avoid po
Inhaltszusammenfassung zur Seite Nr. 3
CAUTION 1. For general ventilating use only. Do not use to exhaust hazardous or explosive material and vapors. 2. To reduce the risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings or into attics, crawl spaces or garages. 3. Read specification label on this product for further information and requirements. 4. Use only for the purpose of kitchen ventilation. 5. Do not install this range hood in the bathroom or in other
Inhaltszusammenfassung zur Seite Nr. 4
NAME OF PARTS - Accessories - - Accessories - - Accessories - - Accessories - - Accessories - Screw M5×30 Nut with plate Four (4) pieces Four (4) pieces SIZE & DIMENSIONS (Unit : inch) 4
Inhaltszusammenfassung zur Seite Nr. 5
RANGE HOOD LOCATION The range hood must be installed just above the cooktop. 1 The minimum distance from the cooking surface to the bottom of the range hood must be 24". 2 The total weight of the BUF-03R range hood unit is: 3 BUF-03R-------- 18 lbs. (8 kg) Power requirements are: 4 AC120 V, 60 Hz, 1.8 Amp CAUTION Check that the hood is correctly installed, since incorrect installation could result in the detachment of the range hood and the unit could fall off. To protect hands from injury,
Inhaltszusammenfassung zur Seite Nr. 6
INSTALLATION 1. PREPARATION WARNING If the range hood is not installed properly, it could become detached and fall off. Ensure that the metal duct does not touch other metal housing materials, otherwise fire or electric shock could result. This range hood can discharge upward or backward. According to the conditions 1 where the hood is installed, determine whether it will discharge vertically or horizontally (3¼" × 10" duct). For vertical or horizontal discharge, run duct work between the h
Inhaltszusammenfassung zur Seite Nr. 7
INSTALLATION (continued) Run house wiring between service panel and hood location. 3 Prepare the range hood unit. 4 In case of Vertical Discharge (1) The range hood is supplied with the exhaust pipe fixed on its top plate. (2) Provide a transition duct (not supplied) to connect the exhaust pipe and external duct. For the size of transition duct, refer to Fig. at right. (3) Be sure to keep 1-3/16" overlapping length of the exhaust pipe and transition duct when installing. (4) Skip to page 9
Inhaltszusammenfassung zur Seite Nr. 8
INSTALLATION (continued) In case of Horizontal Discharge (1) Referring to Fig. at right, provide a rectangular hole in the wall for passing through the exhaust pipe. (2) Remove the exhaust pipe from the top of the range hood. NOTE Keep 4 screws (M4×8) for fixing the exhaust pipe later. (3) Detach the cover plate by removing 2 fixing screws, and attach it as shown in Fig. (4) Attach the range hood to the liner. Refer to page 9 for details. (5) Connect the exhaust pipe with the duct, then mak
Inhaltszusammenfassung zur Seite Nr. 9
INSTALLATION (continued) 2. RANGE HOOD MOUNTING Hold up the range hood unit and insert it into the opening of the liner. When the 4 securing plates on both sides have passed through the top of the liner, turn them 1 outward to secure the range hood on the liner temporarily. Make sure that the top of the exhaust pipe is inserted into the bottom of the transition duct. Remove 4 screws which are fixed to the front cover. The front cover swings open 90° as shown in Fig. 2 9
Inhaltszusammenfassung zur Seite Nr. 10
INSTALLATION (continued) Disconnect the wire connector between the push switch assembly and wire box, then detach the front cover by disengaging its hinge part. 3 NOTE Be careful not to damage the hinge part. 2 1 Align 4 screw holes of the liner and range hood unit, then fix securely using the supplied screws (M5×30) and nuts. 4 NOTE Fasten all screws and nuts evenly. Make the duct joint secure and air tight using non-flammable tape such as duct 5 tape, etc. (not supplied) NOTE Make sure that th
Inhaltszusammenfassung zur Seite Nr. 11
INSTALLATION (continued) 3. CONNECTING POWER SUPPLY WIRES WARNING Electrical wiring should be done by a qualified person(s) in accordance with all- applicable codes and standards, including fire-rated construction. An unqualified person doing the work could result in fire, electric shock or injury. This range hood uses 120V AC. Do not connect to other voltage since fire, electric shock or damage could result. Remove the nut from the conduit connector at the end of power wiring. 1 WARNING Be
Inhaltszusammenfassung zur Seite Nr. 12
INSTALLATION (continued) Connect the electrical wires as follows: Connect wires tightly and securely using wire connectors (not supplied). 4 Black to Black White to White Green to Green Replace the wire cover with the screw removed previously. Make sure that all wires are connected properly and enclosed inside of the wiring compartment. 5 12
Inhaltszusammenfassung zur Seite Nr. 13
INSTALLATION (continued) 4. FINAL ASSEMBLY AND CHECK One 40 W light bulb (not supplied) can be mounted to this range hood. Prior to final assembly, install a light bulb (ordinary type, in the base diameter 17 mm), rated 120 V-40 W or below. Assembly (1) Hang the front cover on the hinge part. 1 (2) Connect the wire connector and replace the front cover with 4 screws. CAUTION To prevent the screw holes from being damaged, be sure to tighten the screws with the torque of 13 inch-lbs. (1.5 N-m) o
Inhaltszusammenfassung zur Seite Nr. 14
INSTALLATION (continued) 5. EXPLANATION TO THE END USER (1) Refer to the Operation Manual, explain the operation of this range hood to end users. (2) The Installation Manual and Operation Manual should be given to the end user. CIRCUIT DIAGRAM 120V 60Hz Motor Green Connector Terminal White Black Capacitor Red White Orange Red Brown Blue Bulb:Max40W Connector Blue Brown Orange White Black Red Green Control Switch 14 Blue Brown Orange White Black Green
Inhaltszusammenfassung zur Seite Nr. 15
Fuji Industrial USA, Inc. 16300 Christensen Rd., Ste-212 Seattle, WA 98188-3403 Telephone: 1-888-547-9880
