Inhaltszusammenfassung zur Seite Nr. 12
Operation TIMER operation Set Clock correctly before starting Timer operation(referring to page 5) You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night. TIMER ON/OFF (1)After unit start, select your desired operation mode. Operation mode will be displayed on LCD. A Power indicator on indoor unit lights up. (2)TIMER mode selection Press TIMER button to change TIMER mode. Every time the butto
Inhaltszusammenfassung zur Seite Nr. 13
Operation TIMER ON-OFF (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. (2) Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: A blank ON OFF ON OFF TIMER ON TIMER OFF TIMER ON-OFF Select TIMER ON-OFF. "ON" will flash. (3)Time setting for TIMER ON TEMP ON Press HOUR button. OFF SWING FAN 1 Every time the button is pressed, time increases 10min. MODE
Inhaltszusammenfassung zur Seite Nr. 14
Operation A Comfortable SLEEP Before going to bed at night, you can simply press the SLEEP button and unit will bring you a sound sleep in selected mode. TEMP ON OFF SWING FAN MODE SLEEP CLOCK SET TIMER LOCK RESET CODE In COOL ,DRY mode One hour after SLEEP mode starts, temp. will o become 1 C higher than temp. setting. After o running for another 1 hour, temp. rises by 1 C further. Unit will run for 6 hours then stops automatically. Temp. is higher than temp. SLEEP operation starts SLE
Inhaltszusammenfassung zur Seite Nr. 15
Operation Emergency operation and test operation Emergency Operation: Carry out this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed, a " Pi " sound starts once, which means the start of this operation. In this operation, it is not possible to change the settings of temperature and air flow speed, it is "Pi"! also impossible to do an operation by the timer. Follow the requirements below. Room Designated Timer Air flow Oper
Inhaltszusammenfassung zur Seite Nr. 16
Maintenance Different models have different appearance. Cleaning of unit casing Cut off power supply before cleaning wipe unit casing with soft cloth. In case of heavy stain, clean it with neutral detergent. squeeze water in the cloth, wipe off the detergent on unit casing completely. Cleaning of remote controller Don't use water to wash unit casing, please use dry cloth. Don't use glass cleanner or cloth soaked with chemicals. Cleaning of air filter Air Filter 2.Remove air filters 1.Open
Inhaltszusammenfassung zur Seite Nr. 17
Maintenance Replacement of Electrostatic Filter Detach the Air filters. 1 2 Detach the Electrostatic Filters. Be careful with fins. 3 Replace the old filter with new one into the frame. Pull up the hook to the designated direction White side should be up side. 4 Open the frame of the filter. 5 Attach the Electrostatic Filters. Attach the Air Filters. 6 Close the inlet grille. Some of the models may not have the frame of the filter. If Electrostatic Filter can no longer be used, please buy a new
Inhaltszusammenfassung zur Seite Nr. 18
Maintenance Better use of air conditioner Cleaning of the air filter. Proper room temperature. Once every two weeks Proper temperature Effective use of the timer. Closing of doors and windows during operation. Curtains or blinds for windows Avoid time-wasteful operation Never fail to observe the followings Do not sprinkle water over the Do not block the inlet or outlet. unit.. Do not pull power plug. Do not use for other purposes. Such as food preservation. plant cult
Inhaltszusammenfassung zur Seite Nr. 19
Trouble shooting Before asking for service, check the following first. Phenomenon Cause or check points The system does not restart When unit is stopped, it won't restart immediately until 3 minutes have elapsed immediately. to protect the system. When the electric plug is pulled out and reinserted, the protection circuit will work for 3 minutes to protect the air conditioner. During unit operation or at stop, a swishing or gurgling noise may be heard. At first 2-3 Noise is heard : minutes af
Inhaltszusammenfassung zur Seite Nr. 1
AS072AZNBA
AU072ABNCA
(HSU-07CG03/R1)
AS092AMNBA
AU092ABNCA
(HSU-09CG03/R1)
AS122AYNBA
AU122ABNCA
(HSU-12CG03/R1)
AS162ATNBA
AU162AFNBA
(HSU-16CG03/R1)
AS182ASNBA
AU182AFNDA
(HSU-18CG03/R1)
AS222AJNBA
AU222AHNBA
(HSU-22CG03/R1)
Please read this operation manual before using the air conditioner.
No.0010544375
Inhaltszusammenfassung zur Seite Nr. 2
Contents Cautions 1-2 Parts and functions 3-5 Operation 6-13 Maintenance 14-16 Trouble shooting 17
Inhaltszusammenfassung zur Seite Nr. 3
Cautions The cardboard box may be broken or cut into 1
Inhaltszusammenfassung zur Seite Nr. 4
20 07,09,12 16,18 22 Series 2 2 2 2 2 Type 3G1.5mm +2x0.75mm 3G2.5mm +3x0.75mm 4G1.5mm 2
Inhaltszusammenfassung zur Seite Nr. 5
Parts and Functions Indoor Unit Test running switch(manual) Used only for test running in cooling o when room temp. is below 16 C . Don't use it in normal operation. Inlet grille Emergency switch(manual) Used when remote controller is lost or defective. Unit will run temporarily. Remote signal receiver Air filter A beeping sound is generated when a signal from remote controller is received. Vertical flap Timer mode indicator Power indicator Operation mode indicator Use remote controller to
Inhaltszusammenfassung zur Seite Nr. 6
Inhaltszusammenfassung zur Seite Nr. 7
Parts and Functions Operation Buttons and display of the remote controller. 1 15 1. Mode display AUTO 2 16 COOL B A DRY 17 3 FAN LO AUTO MED HI 18 4 AUTO 2. SWING display 19 3. FAN SPEED display 5 4. HEALTH display 5. SLEEP display 6 ion 20 6. LOCK display 21 7. TIMER ON display 7 8. AUXILIARY HEAT display TEMP 9. SWING ON 8 10. MODE OFF SWING FAN 22 Used to select AUTO,COOL,DRY ,HEAT 9 and FAN MODE SLEEP 23 11. CLOCK Used to select your desired temp. 24 10 12. TIMER CLOCK SET Used to select
Inhaltszusammenfassung zur Seite Nr. 8
- + + - A TEMP ON OFF SWING FAN MODE SLEEP CLOCK SET TIMER RESET CODE LOCK REMOTE MODEL:YR-H05 CONTROL UNIT NEW 1.DO BA NO TTERIESAND TMIX OLD WITH DO NOTUSE BATTERIES T OF OGETHER DIFFERENTTYPES 2.INSER (TWO)TCORRECTL R-03 Y BATTERIES 2 I N T H E + - P O L A R I T Y 3.PLEASE BATTERIESWHEN REMOVETHE THE REMOTE CONTRLLER NEW DISORDER,AND ÕS AFTER SIX RELOAD M I N U T E S Operation Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indo
Inhaltszusammenfassung zur Seite Nr. 9
A TEMP ON 1 OFF FAN SWING 4 3 MODE SLEEP 2 CLOCK SET TIMER LOCK RESET CODE 9 7
Inhaltszusammenfassung zur Seite Nr. 10
Operation COOL and DRY operation Recommendations: Use COOL in summer. Use DRY in spring, autumn and in damp climate. (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. A (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: COOL AUTO DRY FAN TEMP ON 3 1 OFF Unit will run in operation mode displayed on LCD. SWING FAN 5 6 4 Stop display at your desired
Inhaltszusammenfassung zur Seite Nr. 11
Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig. COOL Level o About 10 Left and right air flow adjustment Up and down (Use remote controller) (manual) Press SWING button, vertical flap will move within Move the horizontal blade by a knob on air the range shown in the Fig. Press SWING button conditioner to adjust left and right direction stop it at a fixed position. referring to Fig
