Inhaltszusammenfassung zur Seite Nr. 1
Video Cassette Recorder
VRB411AT
VRB611AT
Hookup Pages
Important!
Return your Warranty Registration
Card within 10 days. See why inside.
Inhaltszusammenfassung zur Seite Nr. 2
75V ANT / CABLE 6 Hookups without a Cable Box/Direct Broadcast System The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Direct Broadcast System, please see pages eight-nine. If you have a Stereo TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR. (The VRB611 is illustrated here. The VRB411 has single AUDIO IN/OUT jacks.) 1 Disconnect the antenna or cable from your TV. Antenna Indoor/Outdoor (300 ohm) 75V ANT
Inhaltszusammenfassung zur Seite Nr. 3
75V ANT / CABLE Hookups without a Cable Box/Direct Broadcast System (cont’d) 7 3 Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type (supplied) or screw-on type of coaxial cable, whichever you prefer.) ANT AUDIO IN L OUT IN R Antenna VIDEO OUT CH3 CH4 IN OUT ANT or Cable AUDIO IN L 75V ANT / CABLE OUT IN R OUT VIDEO ANTENNA IN Jack (on back of TV) CH3 CH4 IN example only OUT RF coaxial cable 4 Pl
Inhaltszusammenfassung zur Seite Nr. 4
75V ANT / CABLE 8 Hookups with a Cable Box/Direct Broadcast System There are two ways to connect your Cable Box/DBS to the VCR. With this connection: l You may view any channel. l You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR. l You may not view a channel other than the one you are recording. l You may not program channels at the VCR. l You can only program a timer recording for one channel at a time. Set the TV and the VCR to the Cable Box/DBS output chan
Inhaltszusammenfassung zur Seite Nr. 5
75V ANT / CABLE IN OUT Hookups with a Cable Box/Direct Broadcast System (cont’d) 9 With this connection: l You may watch one channel while recording another. l You may not record scrambled channels. VCR 1 Cable Box/DBS 2 AUDIO ANT IN L OUT IN R VIDEO OUT CH3 CH4 OUT IN RF coaxial Cable cable Signal TV’s ANTENNA RF coaxial IN Jack 3 cable Connections 1 Connect a Cable signal to the VCR’s ANT(enna) IN Jack. 2 Use an RF coaxial cable (supplied) to connect the OUT Jack on the VCR to the IN Jack on
Inhaltszusammenfassung zur Seite Nr. 6
10 Hookups with a Stereo TV antenna or VRB611 cable to 1 ANT(enna) IN Jack ANT AUDIO IN L OUT IN R VIDEO OUT CH3 CH4 OUT IN Audio and Video IN Jacks on TV VIDEO (yellow) and AUDIO (red and white) Video Cable 2 OUT Jacks Stereo Audio Cable 3 antenna or VRB411 cable to 1 ANT(enna) IN Jack ANT IN AUDIO OUT IN OUT CH3 CH4 VIDEO Audio and Video IN Jacks on TV VIDEO (yellow) and AUDIO (white) OUT Jacks Video Cable 2 Audio Cable 3 l Audio and Video cables are not supplied. 1 Connect the antenna or cab
Inhaltszusammenfassung zur Seite Nr. 7
Front Panel 27 F.FWD (Fast Forward) Button When playback is stopped, press to fast forward the tape at high speed. During tape playback, press to fast forward the tape while the picture stays on the screen. Details are on page 41. Press to Remote Sensor select an item in the VCR menu or to change the setting of a Receives a signal from your menu item. remote control so you can oper- ate your VCR from a distance. REW(ind) Button When playback is stopped, press to rewind the tape at POWER Button
Inhaltszusammenfassung zur Seite Nr. 8
28 Rear Panel ANT(enna) IN Jack Connect your antenna or cable here. Details are on pages six-10. AUDIO IN Jack(s) Connect audio cables coming from the AUDIO OUT Jacks of a camcorder, another VCR, or an audio source here. Details are on page 37. The VRB611 is shown here. The VRB411 has only one AUDIO IN jack. AUDIO OUT Jack(s) Connect audio cables going to the AUDIO IN Jacks of a camcorder, another VCR, or an audio system here. Details are on pages 37 and 43. The VRB611 is shown here. The VRB411
Inhaltszusammenfassung zur Seite Nr. 9
Rerecording (Tape Duplication) 37 The instructions on this page show you how to copy tapes. The illustration uses two VRB611 VCRs. Different VCRs may operate differently. To duplicate a tape, make the connections shown, then follow steps 1-7. 1. Audio cables from AUDIO OUT Jacks of VCR 1 to AUDIO IN Jacks of VCR 2 VCR 1 VCR 2 - Recording VCR Playing VCR ANT ANT AUDIO AUDIO AUDIO IN IN L L L IN OUT OUT IN OUT IN R R R VIDEO VIDEO VIDEO OUT OUT CH3 CH4 CH3 CH4 OUT IN IN OUT IN OUT 3. RF coaxial
