Inhaltszusammenfassung zur Seite Nr. 1
VCR
VR401BMG
VR601BMG
Video Cassette Recorder
Video Cassette Recorder
Hookup Pages
Hookup Pages
Inhaltszusammenfassung zur Seite Nr. 2
75 ANT / CABLE 6 Hookups Without a Cable Box/Direct Broadcast System The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a Cable Box or a Direct Broadcast System, please see pages eight-nine. If you have a Stereo TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR. (The VR601BMG is illustrated here. The VR401BMG has single AUDIO IN/OUT jacks.) 1 Disconnect the antenna or cable from your TV. Antenna Indoor/Outdoor (300 ohm) 75
Inhaltszusammenfassung zur Seite Nr. 3
75 ANT / CABLE Hookups Without a Cable Box/Direct Broadcast System (cont’d) 7 3 Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on type (supplied) or screw-on type of coaxial cable, whichever you prefer.) AUDIO ANT L IN OUT IN R VIDEO OUT Antenna CH3 CH4 OUT IN ANT or Cable AUDIO IN L ANT / 75V CABLE OUT IN R OUT VIDEO ANTENNA IN Jack (on back of TV) CH3 CH4 IN OUT example only RF coaxial cable 4
Inhaltszusammenfassung zur Seite Nr. 4
75 ANT / CABLE 8 Hookups With a Cable Box/Direct Broadcast System There are two ways to connect your Cable Box/DBS to the VCR. With this connection: l You may view any channel. l You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR. l You may not view a channel other than the one you are recording. l You may not program channels at the VCR. l You can only program a timer recording for one channel at a time. Set the TV and the VCR to the Cable Box/DBS output ch
Inhaltszusammenfassung zur Seite Nr. 5
75 ANT / CABLE IN OUT Hookups With a Cable Box/Direct Broadcast System (cont’d) 9 With this connection: l You may watch one channel while recording another. l You may not record scrambled channels. VCR 1 Cable Box/DBS 2 AUDIO ANT IN L OUT IN R VIDEO OUT CH3 CH4 OUT IN RF coaxial Cable cable Signal TV’s ANTENNA RF coaxial IN Jack 3 cable Connections 1 Connect a Cable signal to the VCR’s ANT(enna) IN Jack. 2 Use an RF coaxial cable (supplied) to connect the OUT Jack on the VCR to the IN Jack o
Inhaltszusammenfassung zur Seite Nr. 6
10 Hookups with a Stereo TV antenna or VR601BMG cable to 1 ANT(enna) AUDIO IN Jack ANT L IN IN OUT R VIDEO OUT CH3 CH4 OUT IN Audio and Video IN Jacks on TV VIDEO (yellow) and AUDIO (red and white) Video Cable 2 OUT Jacks Stereo Audio Cable 3 antenna or VR401BMG cable to 1 ANT(enna) IN Jack ANT IN AUDIO OUT IN OUT CH3 CH4 VIDEO Audio and Video IN Jacks on TV VIDEO (yellow) and AUDIO (white) OUT Jacks Video Cable 2 Audio Cable 3 l Audio and Video cables are not supplied. 1 Connect the antenna or
Inhaltszusammenfassung zur Seite Nr. 7
22 Front Panel STOP/EJECT Button Press once to stop the tape. When playback is stopped, press to eject the tape. Press to select an item in the menu. Remote Sensor PAUSE Button Receives a signal from your While recording, press to pause the recording. Press remote control so you can oper- again to resume recording. Details are on page 25. You ate your VCR from a distance. can not pause a One-Touch Recording. During tape POWER Button playback, press to freeze the picture. Press again to Press to
Inhaltszusammenfassung zur Seite Nr. 8
Rear Panel 23 ANT(enna) IN Jack Connect your antenna or cable here. Details are on pages six-10. AUDIO IN Jacks Connect audio cables coming from the AUDIO OUT Jacks of a camcorder, another VCR, or an audio source here. Details are on page 32. The VR601BMG is shown here. The VR401BMG has only one AUDIO IN jack. AUDIO OUT Jacks Connect audio cables going to the AUDIO IN Jacks of a camcorder, another VCR, or an audio system here. Details are on pages 32 and 38. The VR601BMG is shown here. The VR40
Inhaltszusammenfassung zur Seite Nr. 9
32 Rerecording (Tape Duplication) The instructions on this page show you how to copy tapes. The illustration uses two VR601BMG VCRs. Different VCRs may operate differently. To duplicate a tape, make the connections shown, then follow steps 1-7. 1. Audio cables from AUDIO OUT Jacks of VCR 1 to AUDIO IN Jacks of VCR 2 VCR 1 VCR 2 - Recording VCR Playing VCR AUDIO ANT ANT AUDIO L IN IN L OUT IN OUT IN R R VIDEO VIDEO OUT OUT CH3 CH4 CH3 CH4 IN OUT IN OUT 3. RF coaxial cable from the OUT jack of
