Inhaltszusammenfassung zur Seite Nr. 1
T
V
–
+
T
G
V
O
P
R
CONTENTS
VIDEO CASSETTE RECORDER
SAFETY FIRST 2
Safety Precautions.............................2
Some Do's And Don'ts .....................4
QUICK SET UP GUIDE 5
HR-S7600EK CHECK THE CONTENTS .................. 5
INSTALLATION ................................6
AUTO SET UP ..................................8
T-V LINK 11
T-V LINK Functions ......................... 11
BASIC OPERATIONS 12
Playback .........................................12
Recording .............................
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY FIRST 2 Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. IMPORTANT n Please read the various precautions on p. 2 – 4 of this instruction manual before installing or operating the recorder. n It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright i
Inhaltszusammenfassung zur Seite Nr. 3
3 CAUTION n When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet. n Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial. The STANDBY/ON button does not completely shut off mains power from the unit, but switches operating current on a
Inhaltszusammenfassung zur Seite Nr. 4
SAFETY FIRST (cont.) 4 Some Do's And Don'ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and interconnec- tions between pieces of equipment) are
Inhaltszusammenfassung zur Seite Nr. 5
T V – + T G V O P R QUICK SET UP GUIDE 5 Dear Customer, Thank you for purchasing this JVC Video Cassette Recorder. Please use this QUICK SET UP GUIDE to help you to set up your video cassette recorder. CHECK THE CONTENTS 1 CHECK ALL THE CONTENTS SHOWN BELOW Video Cassette Recorder REW FF DIGITAL TBC/NR CABLE STANDBY/ON VCR TV /SAT JOG C. RESET S-VIDEO VIDEO (MONO)L –AUDIO– R SHUTTLE +8 1 LCD PROG AUDIO – –:– – TV/VCR TV PROG 4 SP REVIEW 0 REC LINK 6 SP/LP A.DUB VPS/PDC 15dB NORM TV PROG VCR ENTE
Inhaltszusammenfassung zur Seite Nr. 6
QUICK SET UP GUIDE (cont.) 6 INSTALLATION 2 CONNECT VIDEO RECORDER TO TV Place the recorder on a stable, flat surface. Back of TV RF Cable (provided) 21-pin SCART Cable (not provided) TV Aerial Cable Make this (not provided) connection if your TV has a 21-pin AV input Aerial connector connector (SCART) in order to reduce the possibility of interference. 21-pin AV input connector And if you are using a stereo (SCART) TV, you will need this cable in order to enjoy stereo playback of videotapes. Ma
Inhaltszusammenfassung zur Seite Nr. 7
7 Back of TV AUDIO IN connectors S-VIDEO IN connector S-Video cable (not provided) Audio cable Aerial connector (not provided) Mains outlet Mains Power Cord ANT. IN AV1 OUT L S OUT AV1 IN/OUT COMP. Y/C AUDIO OUT R AV2 IN/DECODER PAUSE RF OUT Back of Recorder RF Cable (provided) S-VIDEO CONNECTION NOTES: To connect to a TV with S-VIDEO/AUDIO IN connectors . . . c You can obtain high-quality S-VHS pictures. 1– Connect the aerial, recorder and TV as per "RF CONNEC- c If your television is not stere
Inhaltszusammenfassung zur Seite Nr. 8
QUICK SET UP GUIDE (cont.) 8 AUTO SET UP 3 SET THE TUNER CHANNELS, CLOCK, GUIDE PROGRAM NUMBERS AND VIDEO CHANNEL* The Auto Set Up function sets the tuner channels, clock, VIDEO Plus+ assigned Guide Program numbers and the video channel* automatically the first time the button on the recorder or on the remote is pressed to turn on the recorder after the mains power cord has been plugged into a mains outlet. * Useful if you have connected the video recorder to Before performing the following pro
Inhaltszusammenfassung zur Seite Nr. 9
9 PRESET DOWNLOAD SET THE TUNER CHANNELS BY DOWNLOADING FROM YOUR TV, CLOCK AND GUIDE PROGRAM NUMBERS When you connect the recorder and your TV via fully-wired 21-pin SCART cable (Z pg. 6), you can set the recorder's tuner channels by downloading preset data from your TV instead of using the Auto Set Up function (Z pg. 8). After downloading is completed, the recorder sets the clock and VIDEO Plus+ assigned Guide Program numbers automatically. For details, refer to the instruction manual for your
Inhaltszusammenfassung zur Seite Nr. 10
QUICK SET UP GUIDE (cont.) 10 Auto Set Up results appear on the display panel When both auto channel set and auto clock set have been completed successfully the correct current time will be displayed after the OK button is pressed in item 3 on page 8 or A after performing the item 1 on page 9. When auto channel set has been completed successfully but auto clock set has not, "(PR)1" B will be displayed after the OK button is pressed in item 3 on page 8 or after performing the item 1 on pa
Inhaltszusammenfassung zur Seite Nr. 11
T-V LINK 11 Direct Rec You can start recording the programme that you are watching T-V Link on your TV with simple operation. Press and hold RECORD and press PLAY on the remote control, or press RECORD on the recorder. Follow the procedure below to use this function. Functions TURN ON THE RECORDER When you connect the recorder and your TV via a fully-wired 21-pin SCART cable (Z pg. 6), the following functions are Press . available. You can use these functions only with a TV offering T-V Link, et
Inhaltszusammenfassung zur Seite Nr. 12
PLAY BASIC OPERATIONS 12 The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme. Playback LOAD A CASSETTE Turn on the TV and select the VIDEO channel (or AV mode). Making sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette 1 is pointing towards the recorder. Don’t apply too much pressure when
Inhaltszusammenfassung zur Seite Nr. 13
h d r c a r w a r e o s F y a l P n o w i t o l o S m 13 Still NOTE: Variable-Speed Search Refer to the SHUTTLE ring illustration on the right as ACTIVATE VARIABLE-SPEED you read the following procedures. SEARCH During playback or still, turn the SHUTTLE ring to the right for forward variable-speed search, or to the left for 1 reverse variable-speed search (refer to the illustration on the left). OR During playback, press @ or #. c The more times you press, the faster the playback Still Picture
Inhaltszusammenfassung zur Seite Nr. 14
SP/LP TV/VCR BASIC OPERATIONS (cont.) 14 TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder. Recording LOAD A CASSETTE Insert a cassette with the record safety tab intact (See Turn on the TV and select the VIDEO channel (or AV mode). below). 1 c The counter is reset to 0:00:00 and the recorder power comes on automatically. 5 CHOOSE A PROGRAMME Press TV PROG +/– or the NUMBER keys to select the 1
Inhaltszusammenfassung zur Seite Nr. 15
15 Record One Programme While Watching Another SELECT PRESET TO WATCH Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you 1 wish to view. C. RESET c The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's TV PROG buttons is recorded on the tape. Elapsed Recording Time Indication You can check the exact time of a recording. SET COUNTER DISPLAY Press – –:– – until a counter re
Inhaltszusammenfassung zur Seite Nr. 16
BASIC OPERATIONS (cont.) 16 With VIDEO Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise. VIDEO Plus+ ACCESS VIDEO PLUS+ SCREEN Press PROG. VIDEO PLUS+ Timer 1 Programming [0 – 9] : VIDEO PLUS+ [+/–] : EXPRESS PROGRAMING [PROG] : EXIT Before performing VIDEO Plus+ Timer Programming: c Make sure that the recorder's built-in clock is set The front display panel looks like this: properly. c Insert a cass
Inhaltszusammenfassung zur Seite Nr. 17
17 Satellite Receiver Users SET TAPE SPEED To timer-record a satellite broadcast using VIDEO Plus+: Press SP/LP ( ) to set the tape speed. 1 Set "AV2 SELECT" to the appropriate mode. (Z pg. 37) 2 Perform steps 1 – 7. 4 3 Set the satellite receiver to the appropriate channel before the selected programme begins. SET PDC MODE 4 Leave the satellite receiver's power on. Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ 5 PDC" is lit on the display panel, PDC is s
Inhaltszusammenfassung zur Seite Nr. 18
PDC DATE+/– BASIC OPERATIONS (cont.) 18 If you don’t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder to timer-record the programme. Express Timer ACCESS VIDEO PLUS+ SCREEN Programming Press PROG. 1 Before performing Express Timer Programming: c Make sure that the recorder's built-in clock is set properly. ACCESS PROGRAMME c Insert a cassette with the safety tab in place. The recorder SCREEN will come on automatically. c Turn on the
Inhaltszusammenfassung zur Seite Nr. 19
19 Satellite Receiver Users ENTER PRESET POSITION To timer-record a satellite broadcast using Express Timer Press TV PROG +/– to Programming: – P1 – enter the preset position 1 Set "AV2 SELECT" to the appropriate mode. (Z pg. 37) START STOP 6 corresponding to the 2 Perform steps 1 – 10. Enter "L-2" for the preset position 21:00 = 22:00 broadcasting station you in step 6. SP VPS/PDC OFF wish to record. 3 Set the satellite receiver to the appropriate channel DATE TV PROG before the selected progra
Inhaltszusammenfassung zur Seite Nr. 20
DATE+/– BASIC OPERATIONS (cont.) 20 Check, Cancel And Replace Programmes DISENGAGE TIMER MODE Press ä, then press . 1 ACCESS PROGRAMME CHECK 1 – –:– – SCREEN/DISPLAY Press . 2 PR START STOP CH DATE 1 2 3 1 8:00 10:00 3 24.12 2 2 10:00 10:45 2 25.12 3 11:30 13:00 1 25.12 4 5 6 4 5 6 3 7 8 9 7 PDC 8 4 0 4 [ ] : NEXT 3 1 OK 2 TV PROG+/– START+/– ACCESS PROGRAMME SCREEN/ DISPLAY Press again to check – P1 – more information. Each START STOP time you press , the 3
8:00 = 10:00 next programme's SP
