Inhaltszusammenfassung zur Seite Nr. 1
T
V
–
OK
3
+
T
V
G
P
O
R
VIDEO CASSETTE RECORDER CONTENTS
SAFETY FIRST 2
Safety Precautions ...................... 2
Some Do's And Don'ts ............... 3
HR-J455EK QUICK SET UP GUIDE 4
CHECK THE CONTENTS ........... 4
INSTALLATION .......................... 5
VIDEO CHANNEL SET ............... 6
HR-J256EK
AUTO SET UP............................ 8
BASIC OPERATIONS 10
Playback .................................. 10
HR-J255EK
Recording ................................ 12
Video Plus+ Timer
Programmi
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY FIRST 2 Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTION IMPORTANT n When you are not using the recorder for a long period of time, it is recommended that you disconnect the power n Please read the various precautions on p. 2 – 3 of this cord from the mains outlet. instruction manual before installing or operating the n Dan
Inhaltszusammenfassung zur Seite Nr. 3
3 Some Do's And Don'ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and interconnec- tions between pieces of equipment) are properly made and in
Inhaltszusammenfassung zur Seite Nr. 4
T V – OK 3 + T V G P O R QUICK SET UP GUIDE 4 Dear Customer, Thank you for purchasing this JVC Video Cassette Recorder. Please use this QUICK SET UP GUIDE to help you to set up your video cassette recorder. CHECK THE CONTENTS 1 CHECK ALL THE CONTENTS SHOWN BELOW TV TV/VCR AUDIO – –:– – 123 STANDBY/ON 2 DISPLAY 45 6 SP/LP VPS/PDC DAILY/QTDN. WEEKLY/HEBDO REC LINK TV PROG 7 89 AUX 0000 4 0 START STOP DATE TV Video Cassette Recorder DEBUT FIN PROG EXPRESS 30 SEC 1 PROG ? RF Cable "AA" Batteries (x
Inhaltszusammenfassung zur Seite Nr. 5
5 INSTALLATION 2 CONNECT VIDEO RECORDER TO TV Place the recorder on a stable, flat surface. Back of TV RF Cable (provided) 21-pin SCART Cable (not provided) TV Aerial Cable (not provided) Make this connection if your TV has a 21-pin AV Aerial connector input connector (SCART) in order to reduce the 21-pin AV input connector (SCART) possibility of interfer- ence. Mains Power Cord ENTREE ANT. IN ENTREE/DECODEUR ENTREE/SORTIE ANTENNE AV2 AV1 IN/DECODER IN/OUT SORTIE RF OUT Back of Recorder Mains ou
Inhaltszusammenfassung zur Seite Nr. 6
3 QUICK SET UP GUIDE (cont.) 6 VIDEO CHANNEL SET 3 TUNE THE TV TO VIDEO RECORDER Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. c If you have connected the video recorder to your TV via both an RF cable and a 21-pin SCART cable (AV connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV Connection" below. c If you have connected the video record
Inhaltszusammenfassung zur Seite Nr. 7
3 7 With RF Connection Before performing the following procedure, make sure that: n the mains power cord is plugged into the mains outlet. n the video recorder is turned off and there is no cassette inserted in the recorder. n the connected TV is turned on. n batteries have been installed in the remote control. Press and hold down STOP(5/8) on the recorder until the display 1 panel shows the following. 123 2 Set your TV to UHF channel 52. (Refer to the instructions supplied 2 45 6 with your TV s
Inhaltszusammenfassung zur Seite Nr. 8
QUICK SET UP GUIDE (cont.) 8 AUTO SET UP 4 SET THE TUNER CHANNELS, CLOCK AND GUIDE PROGRAM NUMBERS The Auto Set Up function sets the tuner channels, clock and Video Plus+ assigned Guide Program numbers automatically the first time the button on the recorder or on the remote is pressed to turn on the recorder after the mains power cord has been plugged into a mains outlet. Before performing the following procedure, make sure that: n the TV aerial cable is connected to the recorder. n the mains p
Inhaltszusammenfassung zur Seite Nr. 9
9 Auto Set Up results appear on the display panel When both auto channel set and auto clock set have been completed successfully the correct current time will be A displayed. When auto channel set has been completed successfully but B auto clock set has not, "(PR)1" will be displayed. When neither auto channel set nor auto clock set has been C completed successfully, "--:--" will be displayed. * You can check if the Guide Program numbers have been set correctly when you perform Video Plus+ Timer
Inhaltszusammenfassung zur Seite Nr. 10
REW PLAY 3 BASIC OPERATIONS 10 The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme. Playback LOAD A CASSETTE Turn on the TV and select the VIDEO channel (or AV mode). Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is 1 point toward the recorder. Don’t apply too much pressure when
Inhaltszusammenfassung zur Seite Nr. 11
% % % PLAY PLAY 3 11 Still Picture/Frame-By-Frame Playback PAUSE DURING PLAYBACK Press PAUSE. If there is vertical jitter, use the TV PROG buttons to correct the picture. REW 1 ACTIVATE FRAME-BY-FRAME PLAYBACK Press PAUSE. Each time PAUSE is pressed the tape will advance one frame. 2 OR 123 2 Press or . Each time one of these buttons is pressed 45 6 the tape will move one frame in the direction of the arrow. 7 89 To resume normal playback, press PLAY. 4 0 Slow Motion TV PROG ACTIVATE SLOW-
Inhaltszusammenfassung zur Seite Nr. 12
3 BASIC OPERATIONS (cont.) 12 TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder. Recording LOAD A CASSETTE Insert a cassette with the record safety tab intact (see Turn on the TV and select the VIDEO channel (or AV mode). below). 1 c The counter is reset to 0:00:00 and the recorder power comes on automatically. 5 3 CHOOSE A PROGRAMME Press TV PROG +/– or the NUMBER keys to select the preset you
Inhaltszusammenfassung zur Seite Nr. 13
3 13 Record One Programme While Watching Another SELECT PRESET TO WATCH Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you 1 wish to view. c The programme selected with the TV’s preset controls appears on the TV screen while the one selected with the recorder's TV PROG buttons is recorded on the tape. Elapsed Recording Time Indication You can check the exact time of a recording. SET COUNTER DISPLAY – –:– – Press DISPLAY (or – –:– –) unti
Inhaltszusammenfassung zur Seite Nr. 14
SP/LP 3 BASIC OPERATIONS (cont.) 14 With Video Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise. Video Plus+ ACCESS VIDEO PLUS+ Timer SCREEN Press PROG. VIDEO PLUS+ 1 Programming Before performing Video Plus+ Timer Programming: [0 – 9] = c Make sure that the recorder's built-in clock is set [+/–] : EXPRESS PROGRAMING properly. [PROG] : EXIT c Insert a cassette with the safety tab in place. The recor
Inhaltszusammenfassung zur Seite Nr. 15
% % 15 Satellite Receiver Users SET TAPE SPEED To timer-record a satellite broadcast using Video Plus+: Press SP/LP ( ) to set the tape speed. 1 Perform steps 1 – 7. 2 Set the satellite receiver to the appropriate channel 4 before the selected programme begins. 3 Leave the satellite receiver's power on. SET PDC MODE Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ 5 PDC" is lit on the display panel, PDC is set to ON. ATTENTION If "VPS/PDC OFF" is displayed
Inhaltszusammenfassung zur Seite Nr. 16
PDC SP/LP STOP+/– DATE+/– 3 BASIC OPERATIONS (cont.) 16 If you don’t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder to timer-record the programme. Express Timer ACCESS VIDEO PLUS+ SCREEN Programming Press PROG. 1 Before performing Express Timer Programming: c Make sure that the recorder's built-in clock is set properly. ACCESS PROGRAMME c Insert a cassette with the safety tab in place. The recorder SCREEN will come on automatically
Inhaltszusammenfassung zur Seite Nr. 17
17 Satellite Receiver Users ENTER PRESET POSITION To timer-record a satellite broadcast using Express Timer Press TV PROG +/– to Programming: – P1 – enter the preset position 1 Perform steps 1 – 10. Enter "L-2" for the preset position START STOP 6 corresponding to the in step 6. 21:00 = 22:00 broadcasting station you 2 Set the satellite receiver to the appropriate channel SP VPS/PDC OFF wish to record. before the selected programme begins. DATE TV PROG 3 Leave the satellite receiver's power on.
Inhaltszusammenfassung zur Seite Nr. 18
SP/LP DATE+/– 3 BASIC OPERATIONS (cont.) 18 Check, Cancel And Replace Programmes DISENGAGE TIMER MODE Press ä, then press . 1 123 ACCESS PROGRAMME CHECK 2 45 6 SCREEN/DISPLAY Press . PR START STOP CH DATE 7 89 PDC 1 8:00 10:00 3 24.12 2 10:00 10:45 2 25.12 2 4 3 11:30 13:00 1 25.12 0 4 5 6 TV PROG+/– 7 START+/– 8 [ ] : NEXT 1 ? ACCESS PROGRAMME SCREEN/ OK DISPLAY Press again to check – P1 – more information. Each START STOP time you press , the 3 8:00 = 10:00 next programme's information appe
Inhaltszusammenfassung zur Seite Nr. 19
% Þ % Þ % Þ 3 ADVANCED OPERATIONS 19 Index Search Your recorder automatically marks £ 2 index codes at the beginning of Looking For each recording. This function gives you quick access to any one of 9 index codes in either direction. The Scene NOTE: Before starting, make sure the recorder is in the Stop mode. You Want ACTIVATE INDEX SEARCH Press or (ª or £). “ª 1” or “£ 1” is displayed on screen and search begins in the corre- 1 sponding direction. c To access index codes 2 through 9, pre
Inhaltszusammenfassung zur Seite Nr. 20
% % PLAY 3 ADVANCED OPERATIONS (cont.) 20 B.E.S.T. Picture System The B.E.S.T. (Biconditional Equalised Signal Tracking) system Playback/ checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is “ON”. Recording TURN ON THE RECORDER According To Press . 1 Tape Charac- ACCESS MAIN MENU SCREEN teristics Press MENU. Turn on the TV and select the VIDEO
