Bedienungsanleitung Panasonic MC-V414 00

Inhaltszusammenfassung zur Seite Nr. 1

Order Number MAC0401005C1
Vacuum Cleaner
MC-V414 00
Specifications are subject to change without notice for further
improvement.
© 2004 PANASONIC CONSUMER ELEC-
TRONICS COMPANY, DIVISION OF MAT-
SUSHITA ELECTRIC CORPORATION OF
AMERICA. All rights reserved. Unauthorized
copying and distribution is a violation of law.

Inhaltszusammenfassung zur Seite Nr. 2

MC-V414 00 2

Inhaltszusammenfassung zur Seite Nr. 3

MC-V414 00 1 WIRING DIAGRAM AND DRAWING 1.1. Wiring Diagram 3

Inhaltszusammenfassung zur Seite Nr. 4

MC-V414 00 1.2. PICTORIAL DIAGRAM NOTE: For general servicing, it is necessary to eliminate pinching of any wire during reassembly. After servicing any electrical compo- nent or electrical enclosure, the unit should be reassembled and checked for dielectric breakdown or current leakage. 4

Inhaltszusammenfassung zur Seite Nr. 5

MC-V414 00 2 EXPLODED VIEW AND PARTS LIST 2.1. Body 2.1.1. Exploded View 5

Inhaltszusammenfassung zur Seite Nr. 6

MC-V414 00 2.1.2. Parts List (Body) Ref. No. Part No. Part Name & Description Quantity Remarks 1 AC78KCHTZV07 Dust Compartment 1 Includes Items C-6 & C-7 Packing 2 AC60KBRSZU01 Dust Cover 1 3 AC94EAPNZY02 Power Cord 1 4 AMC-1CTCE23 Wire Connector 6 5 AC02LBJAZ000 Rear Cover Packing 1 6 AC40AYUZV00 Body Packing, Left 1 7 AC39AAJFZV00 Body Packing, Right 1 8 AC01EAMMZ000 On/Off Switch 1 9 AC01EAMMZV07 ON/Off Button 1 10 AC03EAMMZV07 Switch Cover 1 11 AXTN4+16BFY Screw, Switch Cover 1 12 AC60KCHTZV

Inhaltszusammenfassung zur Seite Nr. 7

MC-V414 00 2.2. Nozzle Housing 2.2.1. Exploded View 7

Inhaltszusammenfassung zur Seite Nr. 8

MC-V414 00 2.2.2. Parts List (Nozzle Housing) Ref. No. Part No. Part Name & Description Quantity Remarks 1 AC01ACHTZU03 Nozzle Housing 1 2 AC21H2XZU03 Window 1 3 AMC25S-V00 Shaft (Plastic) 1 4 AC10A2VZV07 Furniture Guard 1 5 AMC81A-V00 Packing (Nozzle) 1 6 AMC43A-2V0 Frame 1 7 AMC58A-2V0 Spring (Pedal) 1 8 AMC47A-2V0U Pedal 1 9 AXTN4+16BFY Screw (Frame) 3 10 AC28SJPZ00 Belt 1 11 AC91AARFZ00 Lower Plate Assembly 1 12 AC27AADGZ00 Lower Plate 1 13 AC07ZADFZ00 Warning Label 1 14 AMC11S-2V0W Belt Cov

Inhaltszusammenfassung zur Seite Nr. 9

MC-V414 00 2.3. Packing Material 2.3.1. Exploded View 2.3.2. Parts List Ref. No. Part No. Part Name & Description Quantity Remarks 1 AC61ZCHTZOOO Packaging Assembly 1 Includes 1 and items a-g 2 ACO1ZCHTZOOO Operating Instructions 1 9

Inhaltszusammenfassung zur Seite Nr. 10

MC-V414 00 3 REPLACEMENT INSTRUCTIONS 3.1. Lower Plate 3.3. Agitator Assembly 3.1.1. Removal 3.3.1. Removal 1. Place handle in low position. 1. The brushes are not replaceable separately. When the 2. Turn the vacuum cleaner over exposing the underside. brushes need replacing, the agitator assembly will have Release the lower plate by pressing the two (2) latches to be replaced. that secure it inward. 3. Separate the lower plate from the vacuum. 2. Carefully lift up on the agitator assembly until

Inhaltszusammenfassung zur Seite Nr. 11

MC-V414 00 3.4.2. Installation 3.4. Nozzle Housing Replacement 1. Install the nozzle packing, if not already in place, window 3.4.1. Removal and handle release assembly in the new nozzle housing. 1.Remove the lower plate as outlined in the LOWER 2. Fit the nozzle around the motor shaft side first, and rotate PLATE REMOVAL/INSTALLATION section. it into place on the dust container as illustrated. 2. Remove the belt and agitator assembly as outlined in the respective sections. 3. Remove the nozzle

Inhaltszusammenfassung zur Seite Nr. 12

MC-V414 00 3.5. Power Cord Replacement 3.6. On / Off Switch 3.5.1. Removal 3.6.1. Removal 1. Remove the seven (7) screws that secure the dust cover 1. Remove the nozzle cover, agitator assembly, belt and and remove the dust cover. nozzle base. 2. Remove the seven (7) screws that secure the dust cover and remove the dust cover. 3. To replace the on-off switch, remove the plastic insert that is mounted over the motor shaft. Lift the motor up and out of the dust compartment. Take care to note the p

Inhaltszusammenfassung zur Seite Nr. 13

MC-V414 00 3.7.2. Installation 3.8. Carbon Brush Replacement 3.8.1. Removal 1. Complete brush change on one side before starting on the other side. There are two (2) brushes located on the motor as identified. Remove the brush assembly by using a Phillips head screwdriver to remove the screw that holds the brush holder onto the motor. 1. Reinstall the motor protector into the dust compartment by aligning the two tabs under the top flange with the slots in the dust compartment by applying pressur