Inhaltszusammenfassung zur Seite Nr. 1
Owner’s Manual
English pp. 1-11
Français pp. 12-17
Central Vacuum Systems
A c c e s s o r i e s
Review this manual before
operating cleaner.
www.hoover.com
Inhaltszusammenfassung zur Seite Nr. 2
Fill in and re t a i n The HOOVER Central Vacuum System Accessories include a hose,nozzle and tools. For your record s ,please enter model and serial nu m b e rs in the spaces prov i d e d b e l ow and retain in a safe place. Power Nozzle Pa rt No. Serial No. (See bottom of power nozzle) A c c e s s o ry kit Model No. (see pack age panel) A t t a ch your sales receipt to this ow n e r ’s manu a l . Verification of purchase date may be r e q u i r e d . I m p o rtant Safeguard s ! I n d e x A s s
Inhaltszusammenfassung zur Seite Nr. 3
1-1 r 1. Unpacking A . C o rd e d H o s e (Models S5697, S5701,S5703) B C o rd e d l e s s H o s e A B (Model S5709) C . Power nozzle (see descriptions below) D. C r evice tool D C E . Dusting brush F. Wall/floor brush E G G . Furniture nozzle H H . Extension wands - some models have two sets of extension wands: • metal wands which can remain attached to the power nozzle F • plastic wands which can be used with cleaning tools. I . H o s e / Tool rack I 1-2 Nozzle Descriptions 1 . S t a n d a
Inhaltszusammenfassung zur Seite Nr. 4
r 2. Assembling 2-1 2-3 2-2 A C D B Push the wand/tool latch on the hand grip For metal wands, attach second wand or For plastic wands, t u rn plastic latch ring (A) to the unlock symbol. tool by fitting button projection (D) on one on wand until outer slot lines up with inner into spring latch (C) of first wand. Attach s l o t . Push the hand grip (A) down onto wand so nozzle in same manner. that the button projection (B) fits into the slot. Push the latch to the lock symbol to To r
Inhaltszusammenfassung zur Seite Nr. 5
3. How to use 3-1 3-2 3-3 A B Hand grip contro l s Floor Surface Switch Handle positions The floor surface switch (B) on the hand ON-OFF Switch The handle has two positions when used with grip controls the agitator on the nozzles. The ON-OFF switch (A) for the Power Unit the power nozzle: upright and operating. is located on the hand grip of the hose. “RUG” turns agitator brush roll ON. To lower handle to operating position, place “BARE” turns agitator brush roll OFF. your foot firmly on the pow
Inhaltszusammenfassung zur Seite Nr. 6
3-5 3-6 E D Note: The headlight (E) on the ‘PowerMAX’ H a rd surface floor cleaning Power nozzles nozzle remains ON as long as the hose The nozzle can be used for cleaning hard Carpet or rug cleaning power cord is plugged into an electrical s u rface floors such as wood, linoleum, When using the nozzle for carpet and ru g o u t l e t . vinyl, asphalt and rubber tile, sealed cork, cleaning, push the Floor Surface Switch (D) c o n c rete and terrazzo, as well as carpet. on hand grip toward “ RU G
Inhaltszusammenfassung zur Seite Nr. 7
4-4 4-5 4-6 C D B Lift up end of agitator. Remove old belt If belt is not broken, pull it off the motor S t retch belt back and attach to motor pulley. f rom agitator pulley (C) and replace with pulley (B). Hold opposite end of agitator in place. new belt. Lettering on belt must be visible. Push belt end forw a rd, rotating end plate (D) until it slides into place. Tu rn agitator, making sure it rotates fre e l y. 4-7 4 - 8 The agitator brush ro l l re p l a c e m e n t What to buy The agitat
Inhaltszusammenfassung zur Seite Nr. 8
When to replace W i n d Tunnel™ power 4 - 1 0 The belt should be checked from time to n o z z l e time to be sure it is in good condition. To check, remove the hood (see following The belt section). Replace the belt if it is stre t c h e d , The belt in your power nozzle drives the cut, or bro k e n . a g i t a t o r. It has been designed specifically How to re p l a c e for use in this nozzle and is important for With CORDED hose,disconnect hose e ffective operation. p ower cord from electr
Inhaltszusammenfassung zur Seite Nr. 9
Agitator brushes and 4 - 1 7 4 - 1 8 brush roll re p l a c e m e n t When to replace brushes With CORDED hose,disconnect hose p ower cord from electrical outlet. W i t h CORDLESS hose,disconnect end of hose from electrified inlet va l v e. E Replace brush roll cover (E) over agitator Position hood on top of nozzle base. b rush roll. Replace 3 short scre w s . Tu rn nozzle over. Replace 2 short scre w s at the back of nozzle and 2 long scre w s at the fro n t . What to buy Headlight re p l a c
Inhaltszusammenfassung zur Seite Nr. 10
Problem: Nozzle won’t pick-up Limited Warranty Clearing blockages (Domestic Use) Remove larger items from carpet and floor Possible cause Applies in United States Only s u rfaces before vacuuming to help pre v e n t Possible solution POWER UNIT o b s t ructions in the hose, wands or nozzle - FIVE YEARS • Low suction. c o n n e c t o r, and maintain the cleaning eff e c- -ALL MODELS • Check Power Unit filter. tiveness of your Central Vacuum System. SUCTION MOTOR 1. To check for obstructions, fi
Inhaltszusammenfassung zur Seite Nr. 11
THE EXCEPTIONAL WARRANTY WITHOUT EXCEPTION* HOOVER CENTRAL VACUUM PRODUCTS APPLIES IN CANADA ONLY CENTRALVACUUM CLEANING ATTACHMENT SETS Full one year warranty covers everything including belts, WARRANTY 1 brushes and bulbs. HOOVER DOMESTIC FLOORCARE APPLIANCE MODELS5671, S5672 THE EXCEPTIONAL CENTRALVACUUM POWER UNIT WARRANTY 5 A full five year warranty on all parts and labour. WITHOUT EXCEPTION* MODELS5673, S5674 A full warranty on all parts and labour in CENTRALVACUUM POWER UNIT accordance wi
