Inhaltszusammenfassung zur Seite Nr. 1
!
m
u
!
!
a
a
3040 Series
O OW WN NE ER R’’S S G GU UIID DE E
G Gu uíía a d de ell D Du ue eñ ño o
L Le e G Gu uiid de e d du u P Pr ro op pr riié ét ta aiir re e
Before Returning, Call
Eureka Customer Service
Antes de enviar de regreso, Ilame al Servico al Cliente de Eureka
Avant de le retourner, appelez le service à la clientèle Eureka
HELPLINE LÍNEA DE AYUDA LIGNE D’AIDE
1-800-282-2886
8 a.m. to 7:30 p.m. (CST), Monday - Friday
10 a.m. to 6:30 p.m. (CST), Saturday - Sunday
8 a.m. a 7:
Inhaltszusammenfassung zur Seite Nr. 2
Where to Find Important Vacuum Information Keep this information Write the model, type and serial number here: Date of purchase (keep your receipt) _______________ Model number and type _________________________ Serial number _________________________________ Find these numbers on a label on the lower back side of the vacuum cleaner. Refer to these numbers when ordering parts and accessories or if service is needed. Before You Start Your Vacuum Cleaner Refer to Quick Start Guide for assembly a
Inhaltszusammenfassung zur Seite Nr. 3
ENGLISH IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing. ! • Do not allow to be used as a toy. Close attention is necessary wh
Inhaltszusammenfassung zur Seite Nr. 4
How to Identify Parts of Vacuum Cleaner Handle Cord retainer Dusting brush ® Power Paw Hose hook On (I)/ Off (O) Nested crevice tool power switch & extension wand Power cord Upper cord wrap Handle / latch Foam filter Carrying handle Hose & HEPA filter Dust cup Quick release Filter screen compartment Hose wand (located in dust cup cord wrap compartment) Hose retainer Hose sleeve Handle release Height adjustment knob Brush roll cover Maintenance Schedule Maintenance Schedule is also located on b
Inhaltszusammenfassung zur Seite Nr. 5
ENGLISH How to Use Accessories Handle must be in upright position. ! Raise height adjustment to ‘high carpet’ before using accessories. Replace hose end into hose retainer afer using accessories. Combination Crevice Tool and Extension Wand Use for baseboards, corners and between cushions. 1) Grasp crevice tool near ridges and pull apart. 2) Turn ridge end to center. 3) Push crevice tool into wand and place on end of hose. Dusting Brush Use for furniture, drapes, blinds, bookshelves, lampshades
Inhaltszusammenfassung zur Seite Nr. 6
How to Maintain Your Vacuum Cleaner ! Make sure vacuum cleaner is turned off and power cord is unplugged. Maintain Brush Roll – part number 77315 Motor can become hot with normal use. Do not remove end caps. Remove hair and threads from brush roll periodically. Check EXT-U Belt. Replace if worn, cut or out of shape – part number 61120C ! Avoid touching the motor shaft when checking brush roll or belt. How to replace brush roll or belt 1) Use handle release to lower handle flat onto floor (Fig
Inhaltszusammenfassung zur Seite Nr. 7
ENGLISH How to Clear a Blockage ! Make sure vacuum is turned off and power cord is unplugged. Hose Blockage 1) Remove hose from hose retainer. Flexing the hose will help loosen any blockage (Fig. 1). 2) Remove dust cup and remove debris Fig. 2A from hose connector opening (Fig. 2A). If still blocked, remove screw from hose connector and remove blockage (Fig. 2B). 3) Hose inlet – remove two screws and brush roll cover. Clear blockage from Fig. 1 Fig. 2B Fig. 3 hose inlet (Fig. 3). The Eurek
Inhaltszusammenfassung zur Seite Nr. 8
Thermal Cut-Off This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum suddenly shuts off, push the power switch to off (O) and unplug the vacuum. Check the vacuum for a possible source of overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the vacuum. After the 30 minute period, plug the vacuum back in and turn on the switch. I
