Bedienungsanleitung Eureka Airspeed Gold HEPA Bagless Upright Vacuum AS1001A

Inhaltszusammenfassung zur Seite Nr. 1

AS1100-AS1109 Series
With cord rewind
Upright vacuum cleaner; household type.
Owner’s Guide
Thank you for purchasing your new Eureka vacuum!
Important instructions
For easy assembly, please take a few
moments to read this owner’s guide.
If you have questions about your new vacuum,
please contact our customer service helpline at
1-800-282-2886. We’re here to help!
8 a.m. to 7:30 p.m. (CST), Monday - Friday
10 a.m. to 6:30 p.m. (CST), Saturday - Sunday
Promotional code: airspeed2011
Special Offer

Inhaltszusammenfassung zur Seite Nr. 2

Where to find important vacuum information Keep this information Write the model, type and serial number here: Date of purchase (keep your receipt) _______________ Model number and type _________________________ Serial number _________________________________ Find these numbers on a label on the middle back side of the vacuum cleaner. Refer to these numbers when ordering parts and accessories or if service is needed. Before you start your vacuum cleaner Refer to Quick Start Guide for assembly an

Inhaltszusammenfassung zur Seite Nr. 3

ENGLISH IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing. ! • Do not allow to be used as a toy. Close attention is necessary wh

Inhaltszusammenfassung zur Seite Nr. 4

Washable How to identify parts of vacuum cleaner SPECIAL FEATURES Available on some models Handle Turbo nozzle Cord clip (on some models) Hose Carry handle Dust cup release Turbo cover Turbo nozzle Filter assembly WAND 22 Air path (located inside dust cup) selector knob Dust cup Wand Wand 2 Stair hose Exhaust/HEPA Crevice tool Power cord filter compartment Dusting brush (located behind dust cup) Cord reel Cord rewind switch Lower hose retainer Power switch Height adjustment knob Brush roll lever

Inhaltszusammenfassung zur Seite Nr. 5

ENGLISH WAND 22 FLOORS How to use accessories Before using accessories C A U T I O N • Pull out cord to desired length. Do not pull past red line (Fig.1). Push cord into cord clip. When using tools, always place handle in upright • Move brush roll lever to off position and put position and move brush roll lever to off position. vacuum in an upright position (Fig. 2). • Turn air path selector knob to ‘tools’ (Fig. 3). • When finished vacuuming, press switch to retract cord (Fig. 4). WAND 2-Positi

Inhaltszusammenfassung zur Seite Nr. 6

How to clear a blockage ! Make sure vacuum is turned off and power cord is unplugged. Hose blockage • Remove hose from hose retainer. Flex the hose to loosen any blockage (Fig.1). • Remove dust cup. Set air path knob to ‘floors.’ Use finger to check for debris (Fig 2). Fig. 1 • Base hose – Pull down to loosen end of base hose. Use finger to clear blockage. Snap hose end back up into position (Fig 3). • Hose connector – Pull out on left side tab to remove connector. Remove debris. Align tab at ri

Inhaltszusammenfassung zur Seite Nr. 7

ENGLISH Check type S belt. Replace if worn, cut or out of shape ! Allow unit to cool completely before servicing. • Remove 4 screws from vacuum cover. Lift off cover (Fig. 1). • Push up gray latch to release; lift up belt cover (Fig. 2). • Remove old belt from wheel first, then from motor shaft (Fig. 3). • Place new belt around motor shaft; pull to loop over top of wheel (Fig. 4). Fig.1 Fig.2 Fig.3 • Rotate wheel and belt toward vacuum front to center belt on wheel (Fig. 5). • Push firmly on bel

Inhaltszusammenfassung zur Seite Nr. 8

Problem solving ! Make sure vacuum is turned off and power cord is unplugged. N O T I C E: Thermal cut-off This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum suddenly shuts off, proceed as follows: 1) Push the power switch to off and unplug the vacuum. 2) Check the vacuum for a possible source of overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes b