Inhaltszusammenfassung zur Seite Nr. 1
!
!
m
!
a
a
u
k
k
8860-8899 Series
O OW WN NE ER R’’S S G GU UIID DE E
G Gu uíía a d de ell P Pr ro op piie et ta ar riio o
L Le e G Gu uiid de e d du u P Pr ro op pr riié ét ta aiir re e
Before Returning, Call
Eureka Customer Service
Antes de enviar de regreso, Ilame al Servico al Cliente de Eureka
Avant de le retourner, appelez le service à la clientèle Eureka
HELPLINE LÍNEA DE AYUDA LIGNE D’AIDE
1-800-282-2886
8 a.m. to 7:30 p.m. (CST), Monday - Friday
10 a.m. to 6:30 p.m. (CST), Saturd
Inhaltszusammenfassung zur Seite Nr. 2
Where to Find Important Vacuum Cleaner Information Please Retain Record the model, type and serial number below. Date of Purchase____________ (keep your receipt) Model & Type______________________________ Serial Number_____________________________ This information is located on the rating plate on the lower back side of the vacuum. Refer to these numbers when ordering parts, accessories or when service is needed. Before You Start Your Vacuum Cleaner Refer to Quick Start Guide for assembly and u
Inhaltszusammenfassung zur Seite Nr. 3
ENGLISH IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing. ! • Do not allow to be used as a toy. Close attention is necessary wh
Inhaltszusammenfassung zur Seite Nr. 4
How to Identify Parts of Vacuum Cleaner Handle Dusting brush Turbo nozzle Hose Hose hook On (I) / Off (O) power switch Tool caddy, Filter cover, filter On (I) / Off (O) brush roll switch carry handle & and screen Hose wand upper cord wrap (located inside dust cup) Dust cup Self-cleaning duster Nested crevice tool Power cord & extension wand Duster activation knob HEPA filter compartment Quick release cord wrap Hose retainer Headlight Check brush roll light Height adjustment knob Brush roll res
Inhaltszusammenfassung zur Seite Nr. 5
ENGLISH ! How to Use Accessories Handle must be in upright position to ensure that brush roll is lifted off the floor. Make sure brush roll switch in OFF (O) position before using accessories. Replace hose end into duster chamber after using accessories. Telescopic Self-Cleaning Duster (on some models) Use for furniture, blinds, pictures and high-reach areas. Can be used in short or extended positions. 1) Activate static charge: Push power switch ( I ) on and turn activation knob for 10 secon
Inhaltszusammenfassung zur Seite Nr. 6
How to Maintain Your Vacuum Cleaner ! Make sure vacuum cleaner is turned off and power cord is unplugged Maintain Brush Roll Motor can become hot with normal use. Do not remove end caps. Remove hair and threads from brush roll periodically. Check Cogged Belt. Replace if worn, cut or out of shape ! Avoid touching the motor shaft when checking brush roll or belt. How to replace brush roll or belt 1) Use handle release to lower handle flat onto floor. Turn vacuum over on its backside and rem
Inhaltszusammenfassung zur Seite Nr. 7
ENGLISH Maintain Filters Clean or replace filters regularly to maintain suction (see filter maintenace schedule on page 2). ! How to Clear a Blockage Make sure vacuum is turned off and power cord is unplugged. Hose Blockage Loosen lower end of hose and pull hose retainer out to remove hose. Flex hose to loosen any blockage (Fig. 1). Hose Connector Remove dust cup. Use finger to remove debris from hose connector opening (Fig. 2). Base Hose Back of vacuum Remove brush roll cover. See page 4.
Inhaltszusammenfassung zur Seite Nr. 8
Thermal Cut-Off This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum suddenly shuts off, push the power switch to off (O) and unplug the vacuum. Check the vacuum for a possible source of overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting to use the vacuum. After the 30 minute period, plug the vacuum back in and turn on the switch. I
