Inhaltszusammenfassung zur Seite Nr. 1
24944
Universal Remote
Instruction Manual
Control Remoto Universal
Manual de Instrucciones
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Introduction ..................................................................................... 3 Setup .................................................................................................. 3 Battery Installation ............................................................... 3 Battery Saver ........................................................................... 3 Code Saver ...............................................................................
Inhaltszusammenfassung zur Seite Nr. 3
Setup Battery Installation 1. On the back of the remote, push down on the tab and lift the cover off. 2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA Alkaline batteries. 3. Press the battery cover back into place. Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).
Inhaltszusammenfassung zur Seite Nr. 4
vol Button Functions Some buttons on the remote might have functions that are referred to by different names on the device you are controlling. E.G. PREV.CH may be called RECALL, or ENTER may be called DISPLAY. These differences depend on the brand and model of your product. Also, this remote can only operate features that exist on your product. E.G., your product must have PREV.CH ability for the PREV.CH button to operate this feature. TV, CBL/SAT, Red Indicator Lights when VCR/AUX,
Inhaltszusammenfassung zur Seite Nr. 5
vol Button Functions, cont. SETUP Used to setup the remote, and for code search function. SHIFT Press and release to access buttons labeled in reverse print (OK, MENU, EXIT). See “Using SHIFT for Menu and Navigation” description on Page 9 ON•OFF Turns for more information. product On or Off. MUTE Turns off the TV sound while the tv dvd picture remains. OK Selects menu cbl/sat shift dvr/aux setup items for the device rewind play � you are controlling. record stop pause VOLUME UP/DOWN Ch
Inhaltszusammenfassung zur Seite Nr. 6
Direct Code Entry 1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 2. Press and release the desired device button (TV, DVR, etc.). The red indicator blinks, then stays lit. 3. Enter the 4 digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes. 4. With your device on, press ON•OFF. If the device turns off, no further prog
Inhaltszusammenfassung zur Seite Nr. 7
Code Search If your device does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps. 1. Manually turn on the device (TV, DVR, etc.) to be controlled. 2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button. 3. Press and quickly release the desired device button (TV, DVR, etc.). The red indicator blinks off once. 4. Press the ON•OFF button repeatedly
Inhaltszusammenfassung zur Seite Nr. 8
Using Your Remote Code Identification The Code Identification Feature allows you to identify the four digit library code stored under your device button. For example, if you want to find out what four digit code is stored under your TV device button, follow the six steps below: 1. Press and hold the SETUP button until the red indicator stays on. Release the SETUP button. 2. Press and release the desired device button (TV, DVR, etc.). The red indicator blinks, then stays lit. 3. Press
Inhaltszusammenfassung zur Seite Nr. 9
Using Your Remote, cont. Using SHIFT for Menu and Navigation The SHIFT button allows access to more than one function for certain buttons. Use the SHIFT/SETUP button prior to accessing the MENU, OK, EXIT and Navigation functions, for example: For MENU, press and release SHIFT/SETUP then MENU/INFO. For OK, press and release SHIFT/SETUP then OK/MUTE. For EXIT, press and release SHIFT/SETUP then PREV.CH/EXIT. For Up, Down, Left or Right Navigation, press and release SHIFT/SETUP followed
Inhaltszusammenfassung zur Seite Nr. 10
Using Your Remote, cont. Controlling Devices with Separate Power On and Off Buttons Some GE, RCA and ProScan models require you to press the device button for more than one second to turn the device on and the ON•OFF button to turn the device off. Controlling Combo Devices Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/VCR, etc.) will require you to set up two different Mode buttons to control both parts of the Combo device. For example, if you have a TV/DVD Combo, you might need to set u
Inhaltszusammenfassung zur Seite Nr. 11
Using Your Remote, cont. Volume/Mute Control and Punch-Through This remote lets you select which device Mode controls your Volume/Mute buttons. The remote is initially set for all device Modes to use their own Volume/Mute control if present. If the programmed code has no Volume/Mute operation of its own then those buttons will punch-through control to the TV Mode device without needing to change to TV Mode. Any Mode chosen for Volume/Mute control MUST have its own Volume/Mute function o
Inhaltszusammenfassung zur Seite Nr. 12
Using Your Remote, cont. Setting any Mode to use its own Volume/ Mute Control This routine can set any Mode to use only its own Volume/Mute control. Note - If your chosen Mode has no Volume/Mute functions of its own then the Volume/Mute buttons will do nothing. 1. Press and hold the SETUP button until the red indicator turns on, then release the button. 2. Press and hold the MUTE button until the red indicator blinks off, then release the button. 3. Press and release the desire
Inhaltszusammenfassung zur Seite Nr. 13
Troubleshooting Remote does not operate your product. • Press the device button of the product you want to control. • Program the remote with a new code. • Install new batteries. (You might have to reprogram your remote after installing new batteries.) • Remote may not be compatible with your product. Remote does not operate some features of your product. • Sometimes a particular code might operate some features but not all. Try programing remote with a new code. • Remote may not be
Inhaltszusammenfassung zur Seite Nr. 14
90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit. This warranty is in lieu of all other warranties express or implied. Some states do not allow limitations on how long an imp
Inhaltszusammenfassung zur Seite Nr. 15
Tabla de Contenido Introducción .................................................................................17 Configuración .............................................................................17 Instalación de las baterías .............................................17 Ahorrador de baterías ......................................................17 Protección de códigos .....................................................17 Configuración de códigos ......................
Inhaltszusammenfassung zur Seite Nr. 16
Configuración Instalación de las baterías 1. Presione hacia abajo la lengüeta en la parte pos- terior del control remoto y retire la tapa. 2. Inserte dos baterías alcalinas tamaño AAA de manera que correspondan con las marcas + y – del compartimiento. 3. Ajuste nuevamente la tapa haciendo presión. Ahorrador de baterías El control remoto se apagará automáticamente si algún botón se mantiene oprimido por más de 30 se- gundos. Esto prolongará la duración de sus baterías en caso de que el c
Inhaltszusammenfassung zur Seite Nr. 17
vol Funciones de los botones Algunos botones del control remoto podrían tener fun- ciones que corresponden a nombres diferentes en el aparato que está controlando. Por ejemplo, puede que PREV.CH se llame RECALL, o ENTER se llame DISPLAY. Tales diferencias dependen de la marca y el modelo de su producto. Igualmente, este control remoto sólo puede ejecutar funciones que existan en su producto. Por ejemplo, su producto debe tener la función PREV. CH para que el botón PREV.CH pueda ejecutarla
Inhaltszusammenfassung zur Seite Nr. 18
vol Funciones de los botones, continuación SETUP Se usa para configurar el control remoto y para la función de búsqueda de códigos. SHIFT Presione y suelte para acceder a los botones con nombres en impresión invertida (OK, MENU, EXIT). Ver más información en “Uso de SHIFT para menú y navegación” en la página 9. ON-OFF Enciende y apaga el producto. MUTE Silencia el sonido del televisor dejando sólo la imagen. OK Selecciona las tv dvd opciones de menú para cbl/sat dvr/aux shift el aparat
Inhaltszusammenfassung zur Seite Nr. 19
Entrada directa de códigos 1. .. Mantenga presionado el botón ....... SETUP hasta que el indicador rojo permanezca encendido y luego suelte el botón SETUP. 2. . Presione y suelte el botón del aparato deseado (TV, DVR, etc.). El indicador rojo parpadeará y después permanecerá encendido. 3. . Ingrese un código de quat- trodígitos de las tablas de códigos (que se encuentran en una hoja aparte). ....... Nota: Después de ingresar un código válido, el indicador rojo se apagará. En c
Inhaltszusammenfassung zur Seite Nr. 20
Búsqueda de códigos Si el aparato no responde después de haber inten- tado todos los códigos para la marca o si la marca no aparece en la lista, busque el código siguiendo estos pasos: 1. Encienda manualmente el aparato (TV, DVR etc.) que va a controlar. 2. Mantenga presionado el botón SETUP hasta que el indicador rojo permanezca encendido y luego suelte el botón SETUP. 3. Presione y suelte rápidamente el botón del aparato deseado (TV, DVR, etc.). El indicador rojo parpadeará una vez
