Inhaltszusammenfassung zur Seite Nr. 1
Using remote controller
Overview
The RC-482M/480M remote controller is a useful tool that can not
only operate the TX-SR700/700E/600/600E, but also all the other
components of your home theater as well. To operate any
component, first press the Mode button on the remote controller that
corresponds to the component that you wish to control. Then simply
press the desired operation button and the component will operate
accordingly. For example, if you wish to select the CD input source
at the TX-SR
Inhaltszusammenfassung zur Seite Nr. 2
Using remote controller Controlling an Onkyo CD player The connector of the Onkyo compact disc player must be connected to the TX-SR700/700E/600/600E (see page 29). 1. Press the CD MODE button. The CD MODE button lights green. ON STANDBY 2. Press the desired operation button. The buttons shaded in the figure to the left are the operation CD MODE buttons that can be used to control an Onkyo compact disc player. Operation buttons: DISC ON: Turns on and off the compact disc player (same as the VO
Inhaltszusammenfassung zur Seite Nr. 3
Using remote controller Controlling an Onkyo DVD player The connector of the Onkyo DVD player must be connected to the TX-SR700/700E/600/600E (see page 29). 1. Press the DVD MODE button. The DVD MODE button lights green. 2. Press the desired operation button. The buttons shaded in the figure to the left are the operation buttons that can be used to control an Onkyo DVD player. Operation buttons: ON: Turns DVD player on and off STANDBY: Turns DVD player off (Some sets may not respond to this but
Inhaltszusammenfassung zur Seite Nr. 4
Using remote controller Controlling an Onkyo MD recorder The conneÇóctor of the Onkyo MD recorder must be connected to the TX-SR700/700E/600/600E (see page 29). 1. Press the MD MODE button. The MD MODE button lights green. 2. Press the desired operation button. ON STANDBY The buttons shaded in the figure to the left are the operation buttons that can be used to control an Onkyo MD recorder. MD MODE Operation buttons: ON: Turns on and off MD player (same as the STANDBY button on the remote cont
Inhaltszusammenfassung zur Seite Nr. 5
Entering a pre-programming code The remote controller has three learning functions. One is entering Learning a pre-programming code the pre-programmed code for a remote controller of another manufacturer. Another is the normal learning function that enables By entering a pre-programming code, you can have the RC-482M/ the remote controller to learn the codes directly from other remote 480M remote controller operate a component made by another controllers (see page 70). And the last is a macro le
Inhaltszusammenfassung zur Seite Nr. 6
Entering a pre-programming code RCA 382 PHILIPS 152, 162, 191 Pre-programming codes SABA 383 PIONEER 192, 193 SAMSUNG 384, 385, 386, 387, PROSCAN 194 Note: 388, 389, 390 QUASAR 195 If more than one code is given in the table, SANYO 391, 392, 393 RADIO SHACK 196 try each code one by one until you reach a SCOTT 394 RCA 110, 141, 197, 198, code that works (i.e. if the first code does SELECO 395 199, 200 not work, then try the next). SHARP 396, 397, 398, 399 SABA 182, 183, 201 SHINTOM 400 SAMSUNG 20
Inhaltszusammenfassung zur Seite Nr. 7
Operating your programmed remote controller After entering a pre-programming by following the procedure DVD MODE (DVD Player Mode) given above, the following modes become enabled for use. Operations are the same as explained on page 65. VCR MODE (VCR Mode) 1. Press the VCR MODE button. The VCR button lights green. 2. Press the desired operation button. The buttons shaded in the figure to the left are the operation buttons that can be used to control your VCR. VCR MODE VCR The buttons given below
Inhaltszusammenfassung zur Seite Nr. 8
Programming the commands of remote controllers for other devices into the remote controller Programming procedure When programming the commands of another remote controller to the RC-482M/480M remote controller, you must first decide under which MODE button you want the commands to be linked. In general, you will select the MODE button that corresponds to the component you are programming. For example, if you are programming the functions from a remote controller for a compact disc player, you w
Inhaltszusammenfassung zur Seite Nr. 9
Programming the commands of remote controllers for other devices into the remote controller 4. Press and hold down the button (that corresponds to the command you are programming) on the remote controller of the other device until the SEND/LEARN lamp on the remote controller flashes twice. After flashing twice, the SEND/LEARN indicator will light again. 5. Repeat Steps 3 and 4 to transfer all the commands you desire from the other remote controller and program them to buttons on the remote contr
Inhaltszusammenfassung zur Seite Nr. 10
Programming the commands of remote controllers for other devices into the remote controller Erasing the programmed command from one button SEND/LEARN indicator You can only erase memorized commands and not preset ones. 1. Press and hold down the MODE button for the command, press the ENTER button, and then release both buttons. When you press the MODE button, the SEND/LEARN indicator MODE lights. When you press the ENTER button, the lamp turns off. buttons When you release the buttons, the lamp
Inhaltszusammenfassung zur Seite Nr. 11
Using the macro function Programming the macro What is the macro function? A macro function enables you to program a series of button With the macro function, you can program a series of button operations (up to 16) on the remote controller into a single button. operations as a macro into the MACRO button so the macro can be The series of operations are then called a macro. For example, to executed with just one touch. Note that for the macro function, only play a compact disc player connected t
Inhaltszusammenfassung zur Seite Nr. 12
Using the macro function Erasing a macro from the MACRO 1 (or 2) button SEND/LEARN 1. Press and hold down any one of the six MODE indicator buttons, press the MACRO 1 (or 2) button, and then release both buttons. When you press the MODE button, it lights green and the SEND/LEARN indicator lights. When you press the MACRO 1 MACRO 1 MACRO 2 (or 2) button, the indicator turns off. When you release the MODE buttons buttons, the indicator flashes once. 2. Press the MACRO 1 (or 2) button again. The SE
