Inhaltszusammenfassung zur Seite Nr. 1
Assembly Instructions for Model: WFV66
Thank you for choosing Sanus Systems Woodbrook Furniture. The Woodbrook Furniture is
constructed of real hardwood and resonance dampening MDF.
Safety Warning: If you do not understand these directions, or have any doubts about the
safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or
www.sanus.com. Check carefully to make sure that there are no missing or defective parts. Our
customer service representatives
Inhaltszusammenfassung zur Seite Nr. 2
Parts List (Cont) (3) Bottom Shelf - q (3) Mid Shelf - r (3) Door - s (2) Glass Panel Insert - t (3) Back Panel - u (1) Left Side Panel - v (1) Right Side Panel - w (2) Center Panel - x Step 1: Prepare the Side Panels Thread a Cam Pin (a) into each of the smaller holes in each Side Panel (v,w). Tighten each Cam Pin with a Phillips screw driver. Insert a Dowel
Inhaltszusammenfassung zur Seite Nr. 3
Step 2: Prepare Center Panels Thread a Cam Pin (a) into each of the smaller holes in each Center Panel (x). Tighten each Cam Pin with a Phillips screw driver. Insert a Dowel (d) into the larger adjacent hole in the Panels. See Diagram 2 for assistance. Diagram 2 Detailed View x a d Step 3: Prepare Stretchers Add a Cam (b) to each Front Stretcher (o) and Back Stretcher
Inhaltszusammenfassung zur Seite Nr. 4
Step 4: Add Stretchers Add the Front and Back Stretchers (o,p) to the Side Panel (v), by aligning the Cam Pin (a) with the hole which the Cams (b) point to and the Dowel (d) goes into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to the Side Panel in a clockwise motion until the stretchers are secured. See Diagram 4 for assistance. Note: Front stretchers attach to the same side as the hinge holes are on. Diagram 4
Inhaltszusammenfassung zur Seite Nr. 5
Step 6: Add Stretchers Add the Front and Back Stretchers (o,p) to the Center Panel (x), by aligning the Cam Pin (a) with the hole which the Cams (b) point to. The Dowel (d) goes into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to the Center Panel in a clockwise motion until the stretchers are secured. See Diagram 6 for assistance. Note: Front stretchers attach to the same side as the hinge holes are on. Diagram 6
Inhaltszusammenfassung zur Seite Nr. 6
Step 8: Add Stretchers Add the Front and Back Stretchers (o,p) to the Center Panel (x), by aligning the Cam Pin (a) with the hole which the Cams (b) point to. The Dowel (d) fits into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to the Side Panel in a clockwise motion until the stretchers are secured. See Diagram 8 for assistance. Note: Front stretchers attach to the same side as the hinge holes are on. Diagra
Inhaltszusammenfassung zur Seite Nr. 7
Step 10: Add Shelf Pins and Bottom Shelf Thread the Shelf Pins (e) into the bottom hole in the line of holes in each Panel (v,w,x). Tighten Shelf Pins with a Phillips screw driver. Add the Bottom Shelf (q) by inserting it into the assembly and press fit it onto the Shelf Pins. Make sure the Bottom Shelf is flush against the Front Stretcher (o). If there is a gap in front the Bottom Shelf may be backward. See Diagram 10 for assistance. Diagram 10 Detailed View
Inhaltszusammenfassung zur Seite Nr. 8
Step 12: Prepare Doors Insert each Phillips Bolt (h) through the Door (s) and into the Door Handle (i). Tighten with a Phillips screw driver. See Diagram 12a for assistance. The Door Panels can be interchanged by removing and re-installing the plastic border from the perimeter of the Door’s back side. Insert a Hinge Screw (j) through the Hinge (l) and thread it into the Door (s). Tighten each with a Phillips screw driver. Repeat process until each Hinge Assembly is secure. See Diagram 12b for
Inhaltszusammenfassung zur Seite Nr. 9
Step 14: Add Mid Shelves Thread a Shelf Pin (e) into the desired location in the Panels (v,w,x). For each shelf, four Shelf Pins will be required. Insert each Mid Shelf (r) into the assembly and press fit onto the Shelf Pins. Make sure the wood strip on each shelf is facing toward the front. See Dia- gram 14 for assistance. Note: Diagram 14 is a Back View. Detailed View Diagram 14 v x x e r
Inhaltszusammenfassung zur Seite Nr. 10
Step 16: Hinge Adjustment for Woodbrook Door Each hinge Assembly is adjustable in multiple directions. See Diagram 16 for assistance. Diagram 16 Side Adjustment Depth Adjustment Height Adjustment Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05 Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
