Inhaltszusammenfassung zur Seite Nr. 1
MGP 462
MGP 462D
Multi-Graphic Processor
68-840-01 Rev. C
08 06
Inhaltszusammenfassung zur Seite Nr. 2
Precautions Safety Instructions • English Warning Power sources � This equipment should be operated only from the power source indicated on the product. This symbol is intended to alert the user of important operating and maintenance This equipment is intended to be used with a main power system with a grounded (neutral) (servicing) instructions in the literature provided with the equipment. conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it. Power d
Inhaltszusammenfassung zur Seite Nr. 3
Quick Start — MGP 462, cont’d Quick Start — MGP 462 Step 4 Installation Attach an output device to the RGB/R-Y, Y, B-Y Step 1 RGBHV/YUV BNC connectors (shown below) and/or to the Install the four rubber feet on the bottom of the 15-pin HD output connector MGP 462, or mount the unit using the supplied (shown at right). rack mounting brackets. RGBHV RGBS R G B R G B /R-Y /Y /B-Y /R-Y /Y /B-Y HV S HV S Rack-mount Bracket R G B R G B /R-Y /Y /B-Y /R-Y /Y /B-Y HV S HV S RGsB HDTV Component Video Rack
Inhaltszusammenfassung zur Seite Nr. 4
Quick Start — MGP 462, cont’d Quick Start — MGP 462, cont’d Getting Started After you have installed and Default Extron Multi-Graphic Power Cycle 2 sec. connected the MGP 462, follow on 2 sec. Processor MGP 462 V2.01 these steps to configure and adjust it to get it ready for use. MENU Configuring the MGP 462 Auto Image 20 sec. Step 1 Use the Input Configuration menu to configure MENU each of the six inputs. Input Configuration 20 sec. Step 2 Use the Output Configuration menu
Inhaltszusammenfassung zur Seite Nr. 5
Quick Start — MGP 462, cont’d Step 8 Step 10 For each input, size and position the image When finished adjusting the desired picture within both window 1 and window 2. controls, save your configuration as a window preset: a. Press one of the six input buttons in the top row (for window 1) or the bottom row a. Press the Preset Recall/Save button (for window 2). and hold it for at least 2 seconds. b. Press the window button that corresponds b. Use either Adjust knob to select the preset with the i
Inhaltszusammenfassung zur Seite Nr. 6
Quick Start — MGP 462, cont’d Quick Start — MGP 462, cont’d QS-4 MGP 462 � Quick Start
Inhaltszusammenfassung zur Seite Nr. 7
Table of Contents Chapter 1 � Introduction ....................................................................................................... 1-1 About This Manual ............................................................................................................. 1-2 About the MGP 462/462D................................................................................................ 1-2 Features .....................................................................................
Inhaltszusammenfassung zur Seite Nr. 8
Table of Contents, cont’d Window Text Configuration menu ................................................................................. 3-14 Window Text Position submenu............................................................................... 3-14 Window Text Size submenu ..................................................................................... 3-14 Windows 1 and 2 Text Color submenus ................................................................... 3-14 Windows 1 and 2 Te
Inhaltszusammenfassung zur Seite Nr. 9
Chapter 5 � Ethernet Configuration and Control ................................................. 5-1 Accessing the Web pages................................................................................................ 5-2 Viewing System Status .................................................................................................... 5-3 Using the Configuration Pages .................................................................................... 5-4 System Settings screen ......
Inhaltszusammenfassung zur Seite Nr. 10
Table of Contents, cont’d Window Presets screen .................................................................................................... 5-18 Naming a window preset ......................................................................................... 5-19 Saving (creating) a window preset .......................................................................... 5-19 Recalling a window preset .......................................................................................
Inhaltszusammenfassung zur Seite Nr. 11
MGP 462 Multi-Graphic Processor Chapter One 1 Introduction About This Manual About the MGP 462/462D Features Application Diagram
Inhaltszusammenfassung zur Seite Nr. 12
Intr Intr oduction, cont’d oduction About This Manual This manual discusses how to install, operate, and configure the Extron MGP 462 multi-graphic processor. Throughout this manual, the terms “MGP,” “multi-graphic processor,” and “processor” are used interchangeably to refer to the same product. About the MGP 462/462D The MGP 462 is a six-input, one-output RGB and video processor that can display two video sources on a single screen in picture-in-picture or picture-by-picture format. It provid
Inhaltszusammenfassung zur Seite Nr. 13
A similar process, 2:2 film detection, is used for PAL film-source video. Background image capture, save, and recall — Background Capture enables you to capture and save the image currently on the output screen. You can then recall the captured image and display it as a background later. ™ Auto Image — Auto Image automatically sizes, centers, and optimizes the image to the scaled output rate, filling the window. Remote control — The MGP 462 can be operated remotely via the RS-232/422 interface
Inhaltszusammenfassung zur Seite Nr. 14
Introduction, cont’d 1-4 MGP 462 � Introduction
Inhaltszusammenfassung zur Seite Nr. 15
MGP 462 Multi-Graphic Processor Chapter Two 2 Installation Mounting the MGP 462 Connecting the MGP 462 Installing or Replacing Button Labels Cabling
Inhaltszusammenfassung zur Seite Nr. 16
Installation, cont’d Installation Mounting the MGP 462 Tabletop use Four self-adhesive rubber feet are included with the MGP 462. For tabletop use, attach one foot to each corner of the bottom side of the unit and place the MGP in the desired location. Rack mounting The MGP can optionally be mounted in a rack with the supplied MBD 149 rack mounting kit (part #70-077-03). Follow these steps: 1. Attach the mounting brackets to the unit using eight of the machine screws supplied with the mounting
Inhaltszusammenfassung zur Seite Nr. 17
Connecting the MGP 462 The MGP 462 processor can be connected to as many as six input devices simultaneously, and two output devices (displaying the same image). Follow the steps below to set up the MGP 462 hardware. Disconnect power to the MGP, and turn off all other devices that will be 1 connected. If the MGP 462 is to be mounted, see Mounting the MGP 462, earlier in this 2 chapter, for the mounting procedure. Using the BNC input connectors, attach up to six video input devices to the 3 MGP
Inhaltszusammenfassung zur Seite Nr. 18
TEXT Installation, cont’d Plunger Base Diffuser Clear Lens 2 Button Label Pry the two 1 pieces apart. Notch Separate the two- piece button at the corner. Replacing a button label 5. Lift out the transparent square label that you want to replace. You may need to use the small screwdriver to gently pry the label out. Do not pry off the translucent diffuser that is behind the label. 6. Insert one of the new label you created in step 1 into the clear button cap, align the white b
Inhaltszusammenfassung zur Seite Nr. 19
Input connectors Inputs 1, 2, 3, and 4 — Plug RGB, component video, S-video, or composite 1 video sources into these BNC connectors as shown in the diagram below. RGBHV Video R/R-Y G/Y B/C H/HV V VID B-Y RGBS or RGBcvS Video R/R-Y G/Y B/C H/HV V VID B-Y RGsB or Component Video R/R-Y G/Y B/C H/HV V VID B-Y S-Video R/R-Y G/Y B/C H/HV V VID B-Y Composite Video R/R-Y G/Y B/C H/HV V VID B-Y 5 6 VID VID /Y Connector signal types for inputs 1 through 4 Input 5 — Plug a component video, S-
Inhaltszusammenfassung zur Seite Nr. 20
Installation, cont’d Clip Down Straight-through Cable 12345678 RJ-45 (for connection to a switch, hub, or router) Connector End 1 End 2 Pin Wire Color Pin Wire Color 1 white-orange 1 white-orange 2 orange 2 orange 3 white-green 3 white-green 4 blue 4 blue 5 white-blue 5 white-blue 6 green 6 green 12345678 7 white-brown 7 white-brown 8 brown 8 brown Crossover Cable (for direct connection to a PC) Twisted Pairs End 1 End 2 Pin Wire Color Pin Wire Color 1 white-orange 1 white-green 7&8
