Bedienungsanleitung Sanus Systems LAS1A

Inhaltszusammenfassung zur Seite Nr. 1

LAS1A
(6901-100147 <01>)
Thank you for choosing the Sanus Systems LAS1A. The LAS1A is designed to mount speakers on each side of a
large VisionMount full motion TV mount. The LAS1A will support speakers weighing up to 11 kg (25 lbs.) each.
CauTION
Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper installation may
cause property damage or personal injury. If you do not understand these directions, or have doubts about
the safety of the installation,

Inhaltszusammenfassung zur Seite Nr. 2

Supplied Parts and Hardware Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item to your dealer; contact Sanus Systems Customer Service. Never use damaged parts! [02] x 2 [03] x 4 [04] x 4 [01] x 2 [05] x 4 [06] x 4 1/4-20 x 2.0 in. 1/4-20 x 1.5 in. 1/4-20 x 1.25 in. 1/4-20 x 0.75 in. [07] x 4 [08] x 4 [09] x 4 [10] x 4 1/4-20 x 0.5 in. M4 x 16mm M4 x 35mm 1/4-20 x 3/8-16 1/4-20 x 3/8-16 [11] x 4 [12] x 4 [13]

Inhaltszusammenfassung zur Seite Nr. 3

1: Preparation 1- 1: New Installations If you have purchased a Sanus Systems large VisionMount™ Full Motion Mount, but have not installed it, begin by following the large VisionMount™ Full Motion Mount instructions. Replace Cross Tube Installation with Step 2: Cross Tube Installation of the LAS1A instructions. When completed, refer back to this Instruction manual, starting at Step 3: Install Extension Tubes. 1- 2: Existing Installations NOTE All graphics in this section are generic and are onl

Inhaltszusammenfassung zur Seite Nr. 4

2: Cross Tube Installation [25] [02] [J] Slide the cross tubes [02] into the first monitor bracket [g], through the arm assembly [H] and then through the second monitor bracket [J]. Center the cross tubes [g] on the back of the TV. Using the Allen Key, tighten the six vise assemblies until the cross tubes no longer rotate. [02] [H] Attach the TV and arm assembly to the wall plate according to the instructions provided with the large VisionMount™ Full Motion Mount. HEAVY! You will nee

Inhaltszusammenfassung zur Seite Nr. 5

4: Install Threaded Tube Clamp & Clamp Knob Slide the threaded tube clamps [05] onto the extension tubes [03], aligning the notches in the threaded tube clamp and cross tubes [02]. Snap the threaded tube clamps onto the cross tubes. Thread a clamp knob [04] onto each threaded tube clamp [05]. Do not tighten at this time. [02] [03] [06] [05] [02] [03] [06] [05] 5: Secure Vise a ssemblies to Brackets [04] [07] [22] [01] 4x NOTE Do not overtighten the nut [22]. The vise assembly [

Inhaltszusammenfassung zur Seite Nr. 6

6: a ttach Speaker Brackets [25] NOTE Slide the speaker brackets [01] into the extension tubes [03]. Maximum extension of the cross tubes is 145cm Use the Allen key to tighten the four vise assemblies [04] until (57 in.). Do not exceed the maximum extension. the speaker brackets do not slide on the extension tubes. [03] [01] [04] [03] 6901-100147 <01>

Inhaltszusammenfassung zur Seite Nr. 7

7: a ttach Speakers 7 - 1: a ttach Speakers using Threaded Fasteners Determine the thread of the fastener required by threading each size fastener into the back of the speaker. Stop immediately if you encounter any resistance. Choose the correct thread size and [03] fastener length for your speakers. If using M4 fasteners, [12] or [13], be sure to install the lock washer [20]. [03] [08] - [13] The speaker wires may be routed to the speaker terminals through the extension tubes [03]. Ref

Inhaltszusammenfassung zur Seite Nr. 8

7 - 2: a ttach Speakers using Hex Studs Choose the correct fastener length, [14] or [15] for your speakers. [14], [15] [03] [23] The speaker wires may be routed to the speaker terminals through the extension tubes [03]. Refer to the instructions provided with the large VisionMount™ Full Motion Mount for routing speaker wires. CauTION Disconnect the speaker wire from the receiver or amplifier when you route it through the upper or lower extension tubes [03] to avoid damage to the speake