Inhaltszusammenfassung zur Seite Nr. 7
PANEL LAYOUT 4 Front Panel 1 2 3 Back Panel 7 4 5 6
Inhaltszusammenfassung zur Seite Nr. 8
PANEL DESCRIPTIONS 1 Reset Button This button will cycle power on the 1:10 Splitter For HDMI 1.3. If the EDID mode has been changed it will not take effect until the unit has been reset. 2 Activity Indicator This LED indicator will turn bright blue when an input signal is detected. 3 Power Indicator This LED indicator will become active once the included 5V DC power adapter has been properly connected. 4 EDID Selection Switch Switches between the built-in Internal EDID and External (Pass-Throu
Inhaltszusammenfassung zur Seite Nr. 9
CONNECTING AND OPERATING THE 1:10 SPLITTER FOR HDMI 1.3 How to Connect the 1:10 Splitter For HDMI 1.3 1. Connect the HDMI or DVI (with a DVI to HDMI adapter or cable) source device to the 1:10 Splitter For HDMI 1.3 HDMI input port using the supplied HDMI cable. 2. Connect up to ten HDMI or DVI (with a HDMI to DVI adapter or cable) displays to the 1:10 Splitter For HDMI 1.3 output ports using user supplied HDMI cables. 3. Connect the included 5V DC power adapter to the 1:10 Splitter For HDMI
Inhaltszusammenfassung zur Seite Nr. 10
EDID MANAGEMENT EDID Mode Selection 1. EXTERNAL MODE: To use this mode, move the EDID switch to the Ext position. See page 8 for details on using the External EDID. 2. INTERNAL MODE: To use this mode, move the EDID switch to the Int position. This mode will use a preset EDID, from the factory, that is stored in the Gefen 1:10 Splitter For HDMI 1.3. This pre-programmed standard EDID data structure is compatible with most A/V display devices. All resolutions and audio formats specifi ed i
Inhaltszusammenfassung zur Seite Nr. 11
EDID MANAGEMENT External EDID Management The 1:10 Splitter For HDMI 1.3 features EDID Management. Before the source can send video or audio signals, the source device reads the EDID (Extended Display Identifi cation Data) from the output devices connected to the Splitter. The EDID contains information about what type of A/V data that the source can send to each output device. The 1:10 Splitter For HDMI 1.3 distributes a single source to multiple output devices. This involves reading EDID
Inhaltszusammenfassung zur Seite Nr. 12
SPECIFICATIONS Video Amplifi er Bandwidth ....................................................................... 225 MHz Input Video Signal .............................................................................. 1.2 Volts p-p Input DDC Signal ......................................................................... 5 Volts p-p (TTL) Supported Resolutions ....................................................... 1080p, 1920x1200, 2K HDMI Connector ............................................
Inhaltszusammenfassung zur Seite Nr. 13
WARRANTY WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notifi ed within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifi cations. Equipment that fails under conditions other than those covered will be repaired at the current
Inhaltszusammenfassung zur Seite Nr. 14
Inhaltszusammenfassung zur Seite Nr. 15
Rev A2 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com Pb This product uses UL listed power supplies.
Inhaltszusammenfassung zur Seite Nr. 1
®
1:10 Splitter for
®
HDMI 1.3
EXT-HDMI1.3-1410-SIL
EXT-HDMI1.3-1410-BLK
User Manual
www.gefen.com
Inhaltszusammenfassung zur Seite Nr. 2
ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday, Pacifi c Time Write To: Gefen, LLC. c/o Customer Service 20600 Nordhoff St Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen, LLC reserves the right to make changes in the hard ware, packaging and any accompanying doc u men ta tion without prior written notice. 1:10 Splitter For HDMI 1.3 is a trademark of Gefen
Inhaltszusammenfassung zur Seite Nr. 3
CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Panel Layout 5 Panel Descriptions 6 Connecting And Operating The 1:10 Splitter For HDMI 1.3 7 EDID Management 9 Specifi cations 10 Warranty
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Congratulations on your purchase of the 1:10 Splitter For HDMI 1.3. Your complete satisfaction is very important to us. Gefen Gefen delivers innovative, progressive computer and electronics add-on solutions that harness integration, extension, distribution and conversion technologies. Gefen’s reliable, plug-and-play products supplement cross-platform computer systems, professional audio/video environments and HDTV systems of all sizes with hard-working solutions that are easy t
Inhaltszusammenfassung zur Seite Nr. 5
OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE 1:10 SPLITTER FOR HDMI 1.3 • By default, display information from the display connected to HDMI output port 1 is sent back to the source. Therefore, the other displays connected to the 1:10 Splitter For HDMI 1.3 must be capable of accepting the timings, resolutions and audio formats of the display that is connected to HDMI output port 1. It is recommended that the display with the lowest native resolution be connected to H
Inhaltszusammenfassung zur Seite Nr. 6
FEATURES HDMI 1.3 Features • 225 MHz (up to 12 bit YUV 444 supported @ 1080p) • Deep Color • Color Space Conversion • Dolby TrueHD and DTS-HD Master Audio • Lip-Sync Features • Simultaneously displays a single Hi-Def source on up to ten (10) HDTV displays without signal loss • Maintains sharp HDTV resolutions up to 1080p Full HD and 2K • 3DTV Pass-Through • EDID Management for rapid integration of sources and display devices. • Mono-LOK™ Locking HDMI Connectors • Supports the use of DVI sourc
