Bedienungsanleitung Stanton DJLab.2

Inhaltszusammenfassung zur Seite Nr. 1

Inhaltszusammenfassung zur Seite Nr. 2

IMPORTANT TO SAFETY 12. 1. Read these Instructions 2. Keep these Instructions Use only with the cart, stand, tripod, 3. Heed all Warnings bracket, or table specified by the 4. Follow all Instructions manufacturer, or sold with the apparatus. When a cart is used, use caution when 5. Do not use this apparatus near water 6. Clean only with dry cloth moving the cart/apparatus combination to 7. Do not block any ventilation openings. Install in avoid injury from tip-over. accordance wit

Inhaltszusammenfassung zur Seite Nr. 3

Inhaltszusammenfassung zur Seite Nr. 4

Inhaltszusammenfassung zur Seite Nr. 5

Inhaltszusammenfassung zur Seite Nr. 6

SPECIFICATIONS M.201 INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2.2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX. OUTPUT (THD=1%) MASTER MORE THAN +14dBV MAX PHONES MORE THAN +21dBV MAX CHANNEL BALANCE WITHIN 3dB FREQUENCY RESPONSE: LINE 20-20KHz ±2dB PHONO 20-20KHz +2, -3dB (RIAA) MIC 20-20KHz +2/-3dB OUTPUT NOISE (IEC-A WEIGHTED) LINE LESS THAN -90dBV PHONO LESS THAN -80dBV MIC LE

Inhaltszusammenfassung zur Seite Nr. 7

Inhaltszusammenfassung zur Seite Nr. 8

T.60 TURNTABLE CONTENTS 1) Start/Stop Button 10) Tonearm 2) Strobe Dots 11) Arm Rest 3) Slip Mat 12) Counterweight 4) Center Spindle 13) 45-rpm Adaptor 5) Power Switch 14) Position For Preparing Cartridge 6) 33/45 Button 15) Phono Output 7) Target Light Base 16) GND 8) Pitch Control Slider 17) Power Cord Connector 9) Headshell Locking Nut PLACEMENT • Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance. • Do not place th

Inhaltszusammenfassung zur Seite Nr. 9

CONNECTIONS 1. Connect the power cord to the auxiliary power NOTE: outlet on the rear panel of your amplifier or receiver • Be sure to connect the ground terminal firmly to the or to a household AC outlet. M.201. 2. Connect the unit output terminals to the PHONO • If this connection is not made or is loose, a power jack of your M.201. source "HUM" will result. Output terminals Amplifier (Receiver) L (White) >> L Channel R (Red) >> R Channel GND (Spade) >> GND OPERATI

Inhaltszusammenfassung zur Seite Nr. 10

SPECIFICATIONS T.60 POWER SOURCE AC 100V, 50/60Hz (For Japan) AC 110V, 60Hz (For Taiwan) AC 120V, 60Hz (For U.S.A.,Canada,Mexico) AC 220V, 50Hz (For United Arab Emirates,Chile,Argentina) AC 220V, 60Hz (For Philippines) AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel) AC 240V, 50Hz (For Australia,U.K.) POWER CONSUMPTION 7.5 Watts DIMENSIONS 452 (W) x 370 (D) x 86 (H) mm WEIGHT 6.3 Kgs

Inhaltszusammenfassung zur Seite Nr. 11

Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement WARRANTY Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the date of original purcha

Inhaltszusammenfassung zur Seite Nr. 12

cut along dotted line STANTON WARRANTY REGISTRATION CARD If you have internet access, please register your product at www.stantondj.com. Otherwise, return this card completely filled out in order to validate your warranty. PERSONAL INFO Name Address City State Zip Country Telephone PRODUCT INFO Model Number Serial Number Date of Purchase Where did you buy this product?

Inhaltszusammenfassung zur Seite Nr. 13

PLACE STAMP HERE Stanton Magnetics, Inc. 3000 SW 42nd Street Hollywood, FL 33312 U.S.A.