Inhaltszusammenfassung zur Seite Nr. 1
129HS
Blade hedge
Instruction manual
trimmer
Important!
Read this instruction manual carefully
before first operation and strictly observe
the safety regulations!
9 129 101 english 01/2006
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Index Page 1. Safety regulations.....................................................................................................................4 1.1 General safety instructions 4 1.2 Working clothes 4 1.3 Fuelling 5 1.4 When transporting the equipment 5 1.5 Maintenance and repairs 5 1.6 Preparing the equipment for starting 5 1.7 Starting 5 1.8 Working with the machine 6 2. Standard delivery...........................
Inhaltszusammenfassung zur Seite Nr. 4
Safety regulations 1. Safety regulations 1.1 General safety instructions Read the operating instructions carefully before placing in service and keep them in a safe place. Use this power tool with particular caution. Non-observance of safety instructions can lead to a risk to life. Also observe any regulations from your professional body. These operating instructions must always be available at the place of work. All individuals instructed to work with the equipment (includ
Inhaltszusammenfassung zur Seite Nr. 5
Safety regulations 1.3 Fuelling Petrol is very light and highly flammable. Keep away from open flames and never spill fuel. Do not smoke at the operating site or at and near the refuelling site! • Stop the engine prior to refuelling. • Let the engine cool down before refuelling - fire risk! • Open the tank lid slowly to allow any excess pressure in the tank to be reduced without the risk of petrol spraying out. • Fuel may contain substances similar to solvents. Prevent products made
Inhaltszusammenfassung zur Seite Nr. 6
Safety regulations 1.8 Working with the machine • Environmental protection: - Avoid excessive noise and exhaust fumes when operating this power tool, and never run the engine unnecessarily. Ensure compliance with any local noise regulations. - Ensure compliance with any local regulations concerning the cutting of hedges or periods where such work is prohibited. - Before commencing such work, ensure that no birds are nesting in your hedges. If you do discover nesting birds, postpone the
Inhaltszusammenfassung zur Seite Nr. 7
Standard delivery ; Control and function elements 2. Standard delivery • Blade hedge trimmer • Cutting blade protector • Shoulder strap • Tools: combination spanner and screw driver • Instruction manual 3. Control and function elements Cutting blade and gear: Fig. 1 Fig. 1: 1 Cutting blade sheath 2 Cutting blades 3 Cutter gearbox Fig. 2 4 Angular gear 5 Angular gear grease nipple 6 Cutting edge angle straining screw 7 Pivoting lever Fig
Inhaltszusammenfassung zur Seite Nr. 8
Fuelling ; Starting / Stopping the engine 4. Fuelling 5. Starting / Stopping the engine 5.1 Half throttle start position 4.1 Fuel information A high performance two-stroke engine operated Fig. 4 with a petrol:oil mixture (petrol + oil = fuel mixture) or with a special fuel mixture for two-stroke engines available from specialists powers this machine. The fuel mixture can be made up with standard lead- free petrol or with lead-free premium grade petrol. The minimum octa
Inhaltszusammenfassung zur Seite Nr. 9
Starting / Stopping the engine • Always manually guide the rope back into its 5.3 Starting start position with your hand on the starter grip - Observe the safety instructions when starting. do not let it retract on its own. Note: Your new brushcutter is, as standard, fitted A specialist can replace a damaged starter rope. with the "Easy-Start-System". This enables the Once the engine runs, briefly pull the throttle back engine to be started without major effort. By to release the h
Inhaltszusammenfassung zur Seite Nr. 10
Adjusting the handle and mitre gear ; Using your blade hedge trimmer 6. Adjusting the handle and mitre gear 7. Using your blade hedge trimmer Always turn off the engine before any installation or adjustment; place the stop switch in position 7.1 Scope of Application "Stop" and if necessary wait until the blade has The blade hedge trimmer must only be used to trim stopped. hedges, shrubs and bushes. Never use the hedge trimmer for any other purpose. Fig. 7 The maximum thic
Inhaltszusammenfassung zur Seite Nr. 11
Using your blade hedge trimmer Trimming procedures 7.3 Decorative cutting Cut the hedge in several stages, if the hedge needs The trapezoidal cutting pattern shown prevents the to be cut back a great deal. Between the passes, cut lower hedge area from loosing its foliage due to back thicker branches and twigs with pruning shears lack of light. neiden. Fig. 12 Fig. 13 Fig. 10 Fig.12: Firstly, cut the hedge to the desired height. Cuttings c
Inhaltszusammenfassung zur Seite Nr. 12
Operating and maintenance instructions 8. Operating and maintenance Fig. 16 instructions The maintenance and the repair of modern machines as well as their safety-relevant assemblies require qualified specialised training and a workshop equipped with special tools and test equipment. Consequently the manufacturer recommends that all tasks not described in these operating instructions be carried out by a specialised workshop. That specialist has the required trainin
Inhaltszusammenfassung zur Seite Nr. 13
Operating and maintenance instructions Before opening the air filter, close the choke to Under no circumstances must the cutter be prevent dirt entering the carburettor. driven at idle speed! Turn air filter lid (22) clockwise (viewed onto the air Only qualified mechanics must adjust the filter lid), and remove the lid. Remove foam filter regulating screws for idle mixture "L" and full (27) from the lid and clean the area around the load mixture "H". filter. If the idling speed canno
Inhaltszusammenfassung zur Seite Nr. 14
Operating and maintenance instructions disconnected from the high-tension ignition cable. 8.8 Shutdown and storage A spark may cause a fire! Preferably, store the equipment in a dry and secure Spark plugs with resistor (thermal value 200) are place with a full fuel tank. Open flames or similar available in different brands under the following must not be nearby. Prevent unauthorised use – description: particularly by children. BOSCH WS6F For stops longer than four w
Inhaltszusammenfassung zur Seite Nr. 15
Operating and maintenance instructions 8.9 Scheduled maintenance The following information is based on standard operating conditions. For special conditions, such as prolonged daily use, the recommended maintenance intervals should be reduced accordingly. Carburettor Check idling speed X Adjust idling speed X Air filter Clean X Replace X Spark plug Check the electrode gap and adjust, if required X X Replace X X Gearbox lubricant Top up
Inhaltszusammenfassung zur Seite Nr. 16
Specification 9. Specification Engine type SOLO single cylinder two-stroke engine 3 Engine capacity cm 29 Bore / stroke mm 35 / 30 Engine power kW at rpm 1,0 / 7500 Max. permissible speed rpm 9000 no load with cutter Medium idling speed rpm 2800 Fuel tank capacity l 0,5 Fuel mix ratio: with SOLO 2T engine oil 1:50 (2%) with other two-stroke oils 1:25 (4%) Carburettor All-position diaphragm carburettor with primer and integrated fuel pump Air filter Foam filter Ignition Electron
Inhaltszusammenfassung zur Seite Nr. 17
Accessories ; Parts subject to wear and tear; Guarantee 10. Accessories 12. Guarantee The manufacturer guarantees trouble-free quality and will cover the cost of replacing parts which are Accessories Part no. found to be faulty in material or workmanship SOLO 2T engine oil 100 ml 00 83 103 within the prescribed guarantee period after the date of purchase. Please note that specific SOLO 2T engine oil 1 l 00 83 104 guarantee conditions may vary from country to country. If in
Inhaltszusammenfassung zur Seite Nr. 18
Made in Germany SOLO SOLO Postfach 60 01 52 P.O.Box 60 01 52 D 71050 Sindelfingen D 71050 Sindelfingen Germany Tel. 07031-301-0 Phone+49-7031-301-0 Fax 07031-130 Fax +49-7031-149 info@solo-germany.com export@solo-germany.com
