Inhaltszusammenfassung zur Seite Nr. 1
For all customer enquiries or for replacement parts, contact:-
☎ ☎ 0870 609 1901
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
Inhaltszusammenfassung zur Seite Nr. 2
360º Carton Contents Switch Handle Steady Handle Tube Trimmer Head Instruction Electric Cable with Manual moulded on plug Guard IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna Outdoor Products Customer Service Department direct Telephone : 01325 300303, Fax : 01325 318193 Safety If not used properly this trimmer can be dangerous! This trimmer can cause serious injury to the opera- tor and oth
Inhaltszusammenfassung zur Seite Nr. 3
REFITTING SPOOL CAP, MANUALLY FEEDING OR 3. Do not use the trimmer if the electric cables are REPLACING NYLON LINE. damaged or worn. 1. Use the trimmer only in daylight or good artificial light. 4. Immediately disconnect from the mains electricity sup- 2. Avoid operating your trimmer in wet grass, where feasible. ply if the cable is cut, or the insulation is damaged. 3. Take care in wet grass, you may lose your footing. Do not touch the electric cable until the electrical sup- 4. On slopes, be
Inhaltszusammenfassung zur Seite Nr. 4
Assembly Instructions A1 A2 Assembly of Switch Handle to Tube (A1) • Ensure that the internal cable is not twisted. 1. Insert the tube into the switch handle. 2. Push until it clicks into position. • ENSURE THAT THE TUBE IS FULLY LOCATED BY ATTEMPTING TO REMOVE IT. Assembly of Trimmer Head to Tube (A2) • Ensure that the internal cable is not twisted. 1. Insert the tube into the trimmer head. 2. Push until it clicks into position. • ENSURE THAT THE TUBE IS FULLY LOCATED BY B1 B2 ATTEMPTING TO
Inhaltszusammenfassung zur Seite Nr. 5
How to trim and edge G H • WARNING • The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. DISCONNECT FROM THE MAINS ELECTRICITY SUPPLY BEFORE ATTEMPTING ANY MAINTE- J NANCE OR ADJUSTMENT. • BEFORE USE Make sure that both lines are fed out. • Make sur
Inhaltszusammenfassung zur Seite Nr. 6
Cutting Head N To remove spool cap Cap 1. Press and hold in the two cap release latches. (N). 2. Pull cap away from the spoolholder. (N). When refitting the spool cap Cap release 1. Keep all areas of the cap and spoolholder clean. latch Failure to do so may prevent the cap being securely located in the spoolholder. Spool 2. Replace the cap, pressing firmly DOWN towards the spoolholder to ensure cap is fully located. 3. Check that the cap is correctly fitted by trying to remove it without depress
Inhaltszusammenfassung zur Seite Nr. 7
Maintenance R • WARNING Disconnect from the mains electricity supply, before attempting any maintenance or adjust- ment. Cutting head continues to rotate after the trimmer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your Power Trim After you have finished using your Flymo Power Trim fol- low the procedure below: S AVOID ACCIDENTAL STARTING. REMOVE PLUG FROM MAINS AND KEEP FEET AWAY FROM THE SWITCH LEVER WHEN: CLEANING AROUND THE
Inhaltszusammenfassung zur Seite Nr. 8
Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT CHECK ACTION Is the automatic line feed work- Manually feed out line. LINE NOT FEEDING No ing? SEE “MANUAL LINE FEED” OR Is the line fed out and visible? Remove cap and spool, free line LINE TOO SHORT Has line been removed from No and re-fit spool and cap. SEE OR cleat? “CUTTING HEAD” TRIMMER VIBRATES The line may be jammed on the spool. Rewind line to remove Is the
Inhaltszusammenfassung zur Seite Nr. 9
EC Declaration of Conformity I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 NEWTON AYCLIFFE, Co. Durham. DL5 NEWTON AYCLIFFE, Co. Durham. DL5 6UP. Certify that the product:- 6UP Certify the maximum weighted sound 6UP Certify the maximum weighted root Ca
