Inhaltszusammenfassung zur Seite Nr. 1
CARE AND MAINTENANCE
1. Clean your phone with a damp (never wet) cloth. Solvent or detergent should never
be used.
2. If your phone stops working, check to be certain that all modular plugs are properly
“snapped” into their jacks. If the phone still doesn’t work and you have other
telephones installed in your home, check to see if they are working. If they are, try
using your telephone on another outlet. If it still doesn’t work, it is more than likely
that there is a problem with your telephone
Inhaltszusammenfassung zur Seite Nr. 2
D. If the product does not operate normally by following the operating instructions. IMPORTANT SAFETY INSTRUCTIONS Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and may require This symbol is to alert you the important operating or servicing instructions that may appear in your owner’s manual. Always extensive work by a qualified technician to restore the product to normal follow basic safety precautions when
Inhaltszusammenfassung zur Seite Nr. 3
FCC INFORMATION CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES This equipment complies with Part 68 of the FCC Rules. The label affixed to this The telephone company may take changes in its communications facilities, equipment contains, among other information, the FCC Registration Number and Ringer equipment, operations or procedures, where such action is reasonably required and proper in its business. Should any such changes render the customer’s terminal Equivalence Number (REN) for th
Inhaltszusammenfassung zur Seite Nr. 4
BATTERIES CAUTIONARY INSTRUCTIONS INTRODUCTION TO CALLER ID INSTRUCTIONS CAUTION – To Reduce the Risk of Fire or injury to Persons, Read and Follow Read this manual carefully before using this product. these instructions. Congratulations on your purchase of this product! The unit allows you to take 1. Use only the following type and size of battery: 4 ‘C’ size (UM-2) alkaline batteries. advantage of the Caller Identification service that may be offered by your local 2. Do not dispose of the bat
Inhaltszusammenfassung zur Seite Nr. 5
CONTROLS AND FEATURES LOCATION OF CONTROLS Features 1. This product features Caller ID. 2. Displays the caller’s name, telephone number, time and date of the last 64 incoming calls that you have received. 3. Large three lines high resolution LCD display. 4. Display Total and New Calls received in standby screen. 5. Up / Down buttons allow easy scrolling forward or backward through stored call records. 6. Erase button allows call records to be deleted individually or collectively. 7. Real Time Cl
Inhaltszusammenfassung zur Seite Nr. 6
LOCATION OF CONTROLS (CONTINUED) LOCATION OF CONTROLS (CONTINUED) HANDSET BOTTOM OF BASE CAUTION Disconnect the telephone line from the equipment before replacing batteries. BATTERY INSTALLATION When the batteries become weak, the battery icon ( ) will appear in the display. Replace as described below. You must replace the batteries within two minutes, or the caller ID and memories will be lost. Insert four (4) “C” size (UM-2) batteries (not included) in this unit to use the Caller ID a
Inhaltszusammenfassung zur Seite Nr. 7
SETUP PROCEDURE BASIC OPERATIONS DO NOT CONNECT the line cord to the wall outlet until the caller ID setup has PLACING A CALL been completed. Set the language, contrast, time and date as follows: Lift the handset and listen for a dial Press the Key buttons (0-9) for the tone. desired number you wish to call. Press and hold the [] and [] buttons SELECT THE LANGUAGE simultaneously for four seconds until Press the [] or [] button to select "ENTER LANGUAGE" appears, ENG (English), ESP (Spanish)
Inhaltszusammenfassung zur Seite Nr. 8
BASIC OPERATIONS (CONTINUED) BASIC OPERATIONS (CONTINUED) OFF/LO/HI RINGER SWITCH If you subscribe to Call Waiting through If you are in a Pulse dialing area you your local phone company, and you may still take advantage of touch-tone receive another phone call. Simply services after dialing to respond to press the FLASH button to answer the touch-tone prompts. To do this, press Slide the OFF/LO/HI Ringer switch to Slide the OFF/LO/HI Ringer switch to new call. Press the FLASH button again the
Inhaltszusammenfassung zur Seite Nr. 9
BASIC OPERATIONS (CONTINUED) BASIC OPERATIONS (CONTINUED) VIEWING THE CALLER ID MEMORY Verify that the number on the display is Press the number “1” button to store the correct, then press the STORE button displayed number in memory location 1. To view the new calls (NEW CALL When all new calls have been checked, again. The Memory indicator (“MEM”) Repeat steps 1 through 4 to store up to indicator will blink), press the [] or [] “END OF NEW CALL” will appear in the will appear in the display.
Inhaltszusammenfassung zur Seite Nr. 10
BASIC OPERATIONS (CONTINUED) BASIC OPERATIONS (CONTINUED) COPYING CALLER ID INFO TO A MEMORY PRESET CALLING BACK A NUMBER FROM THE CALLER ID MEMORY (OFF-HOOK) Pick up the handset and press the [] Press the CALL BACK button twice and Press the [] or [] button to locate a Press the STORE button twice: or [] button to locate a caller ID call to the number will be automatically dialed. caller ID call to be copied into a “MEM” will be displayed on the display. be dialed. If the caller’s phone num
Inhaltszusammenfassung zur Seite Nr. 11
The Caller ID unit will not function until you have TROUBLESHOOTING Caller ID service from your local telephone company. Call your local telephone company to PROBLEMS CHECK The Caller ID display does have Caller ID installed on your phone line. Check your phone line connections. Make sure not show the caller's Is any plug disconnected from all modular No dial tone information all connections are secure and connected. phone plugs? Is jack improperly wired? If it is a private call
Inhaltszusammenfassung zur Seite Nr. 12
NOTICE : If your home has specially wired alarm equipment connected to the CONSUMER INFORMATION telephone line, ensure the installation of this equipment KT2012 does not disable your alarm equipment. If you have questions about what will disable alarm equipment, This equipment complies with Part 68 of the FCC rules and the requirements consult your telephone company or a qualified installer. adopted by the ACTA On the bottom of this equipment is a label that contains, among other information, a
