Bedienungsanleitung Metra Electronics 99-8712

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-8712
APPLICATIONS
Mercedes Benz C Class
2005-2007
99-8712
KIT FEATURES
• DIN head unit provision with pocket
KIT COMPONENTS
A) Radio Housing
Antenna Adapter:
• 40-VW12 - Mercedes antenna adapter
A
TOOLS REQUIRED:
Socket Wrench • Torx Screwdriver • Small Flat Blade Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION REV. 10-07-10

Inhaltszusammenfassung zur Seite Nr. 2

99-8712 TABLE OF CONTENTS Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.

Inhaltszusammenfassung zur Seite Nr. 3

F 72 72 F 80 64 80 64 FRONT AUTO A/C REAR F F 72 72 80 64 80 64 FRONT AUTO A/C REAR F 72 72 F 80 64 64 80 AUTO A/C FRONT REAR ESP ESP OFF OFF 3 2 4 5 6 3 2 4 5 6 3 2 4 5 6 99-8712 DASH DISASSEMBLY 2005-2007 MERCEDES BENZ C CLASS A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove cover around shift lever and cup holder. (Figure A) 3 Unclip and remove ashtray assembly. (Figure B) 4 Remove (2) Torx screws from the B bottom of the climate contro

Inhaltszusammenfassung zur Seite Nr. 4

ESP OFF 99-8712 DASH DISASSEMBLY 2005-2007 MERCEDES BENZ C CLASS D 5 Using a small screwdriver push the release clips inside the vents inward and rotate the vents upward to expose the (2) Torx screws behind the vents. (Figure D) 6 Unclip and remove the vent assembly. (Figure E) 7 Remove (4) Torx screws securing factory radio then remove the unit. E (Figure F) F 2

Inhaltszusammenfassung zur Seite Nr. 5

99-8712 KIT ASSEMBLY DIN HEAD UNIT PROVISION A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) Slide the aftermarket head unit into 2 the cage and secure. (Figure B) B 3

Inhaltszusammenfassung zur Seite Nr. 6

99-8712 FINAL ASSEMBLY FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring connections using the EIA c

Inhaltszusammenfassung zur Seite Nr. 7

99-8712 INSTRUCTIONS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION REV. 10/07/10 INST99-8712