Bedienungsanleitung AT&T 2402

Inhaltszusammenfassung zur Seite Nr. 1

2402_map_2ATT 5/7/02 6:32 PM Page 6
REVISED
5/7/02
USER’S MANUAL
Part 2
Expansion Handset 2402
Fold open this manual for information
about this product’s installation
and operation. Please also
read Part 1 — Important
Product Information.
© 2001 Advanced American Telephones. All rights reserved.
AT&T and the Globe Symbol are trademarks of AT&T Corp. licensed to Advanced American Telephones.
Visit us at www.telephones.ATT.com
© 2001 Advanced American Telephones.
All rights reserved.
AT&T

Inhaltszusammenfassung zur Seite Nr. 2

2402_map_2ATT 5/7/02 6:32 PM Page 1 BEFORE YOU BEGIN About Handset Registration • You must register this (and any other) handset with the base, following the directions in “REGISTER THE HANDSET.” This handset is compatible with telephone model 2462. • The original handset that came with the base is automatically registered as Handset 1. • Additional handsets will be assigned Handset 2, Handset 3, Handset 4, Handset 5, Handset 6, Handset 7, and Handset 8. • Whenever you install a handset batte

Inhaltszusammenfassung zur Seite Nr. 3

2402_map_2ATT 5/7/02 6:32 PM Page 2 CHARGE THE BATTERY 1 Install the handset battery pack. Use only the battery supplied with this handset or AT&T Accessory Battery Model 2401, SKU#91077. a) Remove battery compartment c) Replace cover cover by by sliding it on pressing on its track up indentation over battery and sliding case until it downward. snaps firmly into place. b) Place the battery pack in the handset. Match the metal contacts on the battery with the contacts in the battery compartme

Inhaltszusammenfassung zur Seite Nr. 4

2402_map_2ATT 5/7/02 6:32 PM Page 3 REGISTER THE HANDSET 1 Make sure to charge the handset battery pack at least 12 hours. MENU 2 At the 2462 corded base, press . 3 Use or to select DISPLAY BASE-ID. OK 4 Press . The base screen will display the 15-digit Base ID code for about 30 seconds, then return to the idle screen. Write down the Base ID code so you can enter it at the handset in STEP 6 below. 5 At the cordless handset, use the softkey to select REGISTER. 6 Enter the 15-digit Base ID cod

Inhaltszusammenfassung zur Seite Nr. 5

2402_map_2ATT 5/7/02 6:32 PM Page 4 INSTALLATION Belt Clip Attach the belt clip (optional). a) Slide down into b) To remove, lift one side grooves to attach. with your thumbnail and push back. Headset You can use this telephone hands-free when you install any industry standard 2.5 mm headset (purchased separately). For best results, use an AT&T 2.5 mm headset. Plug the headset into the jack located on the left side of the handset (under the small rubber flap). Do not force the connection, bu

Inhaltszusammenfassung zur Seite Nr. 6

2402_map_2ATT 5/7/02 6:32 PM Page 5 Battery Life Battery life depends on how far the handset is from the base, and other environmental conditions. NOTE: For optimum performance, charge your cordless handset in the handset charger every night. Charge the Handset Battery Pack • This battery should remain charged for up to five days. A fully charged battery provides an average talk time of about six to eight hours. • The battery pack needs charging when: – The battery icon ( ) flashes, – A warn