Inhaltszusammenfassung zur Seite Nr. 1
User’s Guide
SISTF10xx-140-LR(T)
SISTF10xx-160-LR(T)
SISTF10xx-170-LR(T)
Stand-Alone Ethernet Switch
• 10Base-T / 100Base-TX to 100Base-FX
Extended Temperature
Hazardous Environment
Transition Networks industrial Ethernet switch
connects 10Base-T / 100Base-TX twisted-pair
copper cable to 100Base-FX fiber-optic cable. It is
designed for harsh industrial environments and is
also available in models that operate in either
SISTF10xx-140-LR(T)
standard or extended temperature ranges.
The SI
Inhaltszusammenfassung zur Seite Nr. 2
SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T) SISTF10xx-160-LR(T) SISTF10xx-170-LR(T) The SISTF10xx-160-LR(T) model includes six (6) copper RJ-45 ports and two (2) The SISTF10xx-170-LR(T) model includes seven (7) copper RJ-45 ports and one (1) duplex fiber-optic ports. duplex fiber-optic port. Part Number Ports 1 - 6: Copper Ports 7 & 8: Duplex Fiber-Optic Part Number Ports 1 - 7: Copper Port 8: Duplex Fiber-Optic 10Base-T/100Base-TX 100Base-FX Duplex 10Base-T/100Base-TX 100Base-FX Duplex Sta
Inhaltszusammenfassung zur Seite Nr. 3
SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T) Installation Installation -- Continued CAUTION: Disconnect the Ethernet switch from the DC power source DIN-Rail Mount BEFORE installing and/or wiring the device. The Ethernet switch includes an aluminum DIN-Rail mounting plate attached to the device’s back panel. To mount the device onto a DIN-Rail: Install the Fiber Cable 1. Insert the top of the DIN-Rail into the upper slot of the mounting plate. The stiff metal spring should be positioned behi
Inhaltszusammenfassung zur Seite Nr. 4
SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T) Installation -- Continued Installation -- Continued Set the Port Alarm Switches Install the Port Alarm Device The port alarm feature is used to determine faults at the copper or fiber ports. A user-supplied port alarm device can be connected to the Ethernet switch to The dip switches are located on the top panel of the device. Use a small flat alert the user whenever a power fault or a port fault occurs. At least one port blade screwdriver or a sim
Inhaltszusammenfassung zur Seite Nr. 5
SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T) Installation -- Continued Operation Power the Ethernet switch Features Auto-Negotiation This device is suitable for use in Class I, Division 2, Groups A, B, C and D or non-hazardous locations only. With the Auto-Negotiation feature, the Ethernet switch automatically configures itself to achieve the best possible mode of operation over the WARNING: EXPLOSION HAZARD - Do not disconnect equipment copper link. The device broadcasts its speed (10 Mb/s
Inhaltszusammenfassung zur Seite Nr. 6
100BASE-FX 100BASE-FX 100BASE-FX 10/100BASE-TX 10/100BASE-TX PWR 1 PWR 1 TX TX PWR 1 PWR 2 PWR 2 PWR 2 FAULT FAULT FAULT RX RX 100M 100M TX TX RX RX 100M 100M SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T) Operation -- Continued Operation -- Continued Status LEDs Use the status LEDs to monitor the Ethernet switch operation in the network. Power and Fault LEDs SISTF10xx-140-LR(T) SISTF10xx-160-LR(T) SISTF10xx-170-LR(T) The three LEDs near the top indicate the power and fault status: PWR1 (amber)
Inhaltszusammenfassung zur Seite Nr. 7
SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T) Cable Specifications Cable Specifications -- Continued The physical characteristics must meet or exceed IEEE 802.3™ specifications. Extended Temperature Models Fiber Cable SISTF1011-140-LRT SISTF1011-160-LRT Bit Error Rate: <10-9 SISTF1011-170-LRT 1300 nm multimode Single mode fiber (recommended): 9 µm Fiber Optic Transmitter Power: min: -20.0 dBm max: -14.0 dBm Multimode fiber (recommended): 62.5/125 µm Fiber Optic Receiver Sensitivity: min: -
Inhaltszusammenfassung zur Seite Nr. 8
SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T) Cable Specifications -- Continued Technical Specifications Copper Cable For use with Transition Networks Model Ethernet switch or equivalent Standards: IEEE 802.3™, 802.3u™; 802.3x™ Category 5: (minimum requirement) Gauge / Attenuation: 24 to 22 AWG / 22.0 dB per 100m @ 100 MHz Data Rate: 10 Mb/s, 100 Mb/s (copper); 100 Mb/s (fiber) Straight-through OR crossover cable may be used. Processing Type: Store and Forward Shielded twisted-pair (STP)
Inhaltszusammenfassung zur Seite Nr. 9
SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T) Technical Specification -- Continued Troubleshooting If the device fails, isolate and correct the fault by determining the answers to the This device has been evaluated as EEx nC IIC T4 equipment under DEMKO following questions and then taking the indicated action: Certificate No. 03 ATEX 0324537U. Each module is suitable for use in Zone 2 Explosive Atmospheres. The device must be installed in a minimum IP 54 enclosure as defined in IEC 60529 and EN
Inhaltszusammenfassung zur Seite Nr. 10
SISTF10xx-140-LR(T) / -160-LR(T) / -170-LR(T) Troubleshooting -- Continued Contact Us 5. Is a 100M LED (near the fiber links) flashing? Technical Support NO Technical support is available 24 hours a day If there is activity on the corresponding fiber port, disconnect and US and Canada: 1-800-260-1312 reconnect the fiber cable to restart the initialization process. International: 00-1-952-941-7600 If there is no activity on the corresponding fiber port, contact Tech Transition Now Support: 80
Inhaltszusammenfassung zur Seite Nr. 11
Compliance Information UL Listed; C-UL Listed (Canada) NOTE: The following part numbers are UL listed: SISTF1013-140-LR, SISTF1013-140-LRT, SISTF1014-140-LR, SISTF1014-140-LRT, SISTF1013-160-LR, SISTF1013-160-LRT, SISTF1014- 160-LR, SISTF1014-160-LRT, SISTF1013-170-LR, SISTF1013-170-LRT, SISTF1014-170-LR, SISTF1014-170-LRT. CISPR22/EN55022 Class A; CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
