Inhaltszusammenfassung zur Seite Nr. 1
Dyna-Switch/24
24 Port 10/100Base-TX
Fast Ethernet Switch
FEP-31024T-2
rev. 2
908 Canada Court
City of Industry, CA 91748 U.S.A.
Phone: 626.964.7873 or 800.346.6668 Fax: 626.964.7880
www.unicomlink.com e-mail: info@unicomlink.com
USER’S MANUAL
©UNICOM 2005. UNICOM and “A Network Systems Solution” are trademarks of UNICOM Electric, Inc.
All rights reserved. Specifications subject to change without notice.
Rev: 09.05
Inhaltszusammenfassung zur Seite Nr. 2
Introduction UNICOM’s DYNA-SWITCH/24 (Rev. 2.0) is a 24-port 10/100BASE-TX Switch that can be used to build high-performance switched workgroup networks. This switch is a store-and-forward device that offers low latency for high-speed networking and is targeted at workgroup, department or backbone computing environments in SME (small, medium enterprise) businesses. The DYNA-SWITCH/24 (Rev. 2.0) Switch features a “store-and-forward “
Inhaltszusammenfassung zur Seite Nr. 3
Package Contents Unpack the contents of the DYNA-SWITCH/24 (Rev. 2.0) and verify them against the checklist below. ν DYNA-SWITCH/24 (Rev. 2.0) Switch ν Power Cord ν Four Rubber Feet ν User manual ν Rack Mount kits DYNA-SWITCH/24 (Rev. 2.0) User manual Rubber Feet Power Cord Rack-Mount Kits Package Contents Compare the contents of your DYNA-SWITCH/24 (Rev. 2.0) package with the standard checklist abo
Inhaltszusammenfassung zur Seite Nr. 4
Ethernet Switching Technology Ethernet Switching Technology has dramatically boosted the total bandwidth of networks, eliminated congestion problems inherent with Carrier Sense multiple access with Collision Detection (CSMA/CD) protocol, and greatly reduced unnecessary transmissions. This revolutionized networking. First, by allowing two-way, simultaneous transmissions over the same port (Full-duplex), which essentially doubled the b
Inhaltszusammenfassung zur Seite Nr. 5
Hardware Description This section describes the hardware of the DYNA-SWITCH/24 and gives a physical and functional overview of this Switch. Physical Dimension The physical dimension of the DYNA-SWITCH/24 is 440mmx 120 mm x 44mm (L x W x H) Front Panel The front panel of the DYNA-SWITCH/24 consists of (24) 10/100Base-TX RJ-45 ports. The LED Indicators are also located on the front panel of the Switch. Front panel of the DYNA-SWITCH/24 (Rev. 2.0) RJ-45 ports (Auto
Inhaltszusammenfassung zur Seite Nr. 6
LED Indicators The LED Indicators gives real-time information of systematic operation status. The following table provides descriptions of the LED status. LED Status Description Green Power On Powe r Off Power is not connected Green The port is connecting with the device. LK/A Blinks The port is receiving or transmitting data. CT Off No device attached. Orange The port is operating in Full-duplex mode. FD/C Blinks Collision of
Inhaltszusammenfassung zur Seite Nr. 7
Rear Panel The 3-pronged power plug is located at the rear panel of the DYNA-SWITCH/24 as shown in the figure. The switch will work with AC in the 100-240V AC, 50-60Hz range. The rear panel of the DYNA-SWITCH/24 Desktop Installation Set the switch on a sufficiently large flat space with a power outlet nearby. The surface should be clean, smooth, level and sturdy. Make sure there is enough clearance around the Switch to allow air circulation and the attachment of cables
Inhaltszusammenfassung zur Seite Nr. 8
Rack-mounted Installation The DYNA-SWITCH/24 comes with a rack-mounting kit (not a standard option for this switch) and can be mounted in any EIA standard sized, 19" rack. The Switch can then be placed in a wiring closet with other equipment. Perform the following steps to rack mount the switch: 1. Position one bracket to align with the holes on one side of the switch and secure it with the smaller bracket screws. Then attach the rem
Inhaltszusammenfassung zur Seite Nr. 9
Network Application This section provides a few samples of network topology in which the switch is used. The DYNA-SWITCH/24 (Rev. 2.0) is designed to be used as a segment switch. With its large address table (4K MAC address) and high performance, it is ideal for interconnecting networking segments. PC, workstations, and servers can communicate with each other by directly connecting with the DYNA-SWITCH/24. The switch automatically learns nodes address, which are subsequently used
Inhaltszusammenfassung zur Seite Nr. 10
Small Workgroup The DYNA-SWITCH/24 can be used as a standalone switch to which personal computers, servers, or a printer server are directly connected to form a small workgroup. Small Workgroup Application 9
Inhaltszusammenfassung zur Seite Nr. 11
Segment Bridge In enterprise networks where large data broadcasts are constantly processed, this switch is an ideal way for departmental users to connect to the corporate backbone. In the illustration below, two Ethernet switches, with PCs, a print server, and a local server attached, are connected to the DYNA-SWITCH/24. Each device in this network can communicate with the others through the DYNA-SWITCH/24. Connecting servers to the Switch allows other users to access the server’s
Inhaltszusammenfassung zur Seite Nr. 12
Technical Specifications This section provides the specifications of the DYNA-SWITCH/24. IEEE 802.3 10Base-T Ethernet, IEEE 802.3u 100Base-TX Fast Ethernet Standard IEEE802.3x Flow Control and Back-pressure IEEE802.1p Class of Service Store and Forward switching architecture Technology Protocol CSMA/CD 14,880 pps per Ethernet port Transfer Rate 148,800 pps per Fast Ethernet port MAC address 4K Mac address table Per port: Link
Inhaltszusammenfassung zur Seite Nr. 13
The packet with a 0~3 precedence value will flow to the low queue and 4~7 valued packets will flow to the high queue. It also supports weight round ration for high and low queue. The rate is 4:1 (4 high queue packets then 1 low queue packet) [Note] The CoS function is included in the switch firmware and will operate automatically when the switch is on. Storage Temp. -10ºC to 70ºC (-40ºF to 158ºF) Operational 0ºC to 45ºC (32ºF to 113ºF) Temp. Operational 10% to 90% (Non-condensing
Inhaltszusammenfassung zur Seite Nr. 14
Dyna-Switch/24 24 Port 10/100Base-TX Fast Ethernet Switch FEP-31024T-2 rev. 2 908 Canada Court City of Industry, CA 91748 U.S.A. Phone: 626.964.7873 or 800.346.6668 Fax: 626.964.7880 www.unicomlink.com e-mail: info@unicomlink.com USER’S MANUAL ©UNICOM 2005. UNICOM and “A Network Systems Solution” are trademarks of UNICOM Electric, Inc. All rights reserved. Specifications subject to change without notice. Rev: 09.05
