Inhaltszusammenfassung zur Seite Nr. 1
USB2507
Integrated USB 2.0
Compatible 7-Port Hub
Datasheet
PRODUCT FEATURES
Integrated USB 2.0 Compatible 7-Port Hub On-Board 24MHz Crystal Driver Circuit or 24 MHz
— 7 Transaction Translators for highest performance
external clock driver
— High-Speed (480Mbits/s), Full-Speed (12Mbits/s) and
Internal PLL for 480MHz USB 2.0 Sampling
Low-Speed (1.5Mbits/s) compatible
Internal 1.8V Linear Voltage Regulator
— Full power management with per port or ganged,
selectable power control Integ
Inhaltszusammenfassung zur Seite Nr. 2
Integrated USB 2.0 Compatible 7-Port Hub Datasheet ORDER NUMBER: USB2507-ADT FOR 80 PIN TQFP LEAD-FREE ROHS COMPLIANT PACKAGE 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright © 2007 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the i
Inhaltszusammenfassung zur Seite Nr. 3
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Table of Contents Chapter 1 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1 OEM Selectable Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Chapter 2 Pin Table 7-Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chapter 3 Pin Configuratio
Inhaltszusammenfassung zur Seite Nr. 4
Integrated USB 2.0 Compatible 7-Port Hub Datasheet List of Figures Figure 3.1 7-Port 80-Pin TQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 4.1 7-Port Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 5.1 LED Strapping Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Inhaltszusammenfassung zur Seite Nr. 5
Integrated USB 2.0 Compatible 7-Port Hub Datasheet List of Tables Table 2.1 7-Port Pin Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Table 4.1 7-Port Hub Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Table 4.2 SMBus or EEPROM Interface Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Table 4.3 Mi
Inhaltszusammenfassung zur Seite Nr. 6
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Chapter 1 General Description The SMSC 7-Port Hub is fully compliant with the USB 2.0 Specification and will attach to a USB host as a Full-Speed Hub or as a Full-/High-Speed Hub. The 7-Port Hub supports Low-Speed, Full-Speed, and High-Speed (if operating as a High-Speed Hub) downstream devices on all of the enabled downstream ports. A dedicated Transaction Translator (TT) is available for each downstream facing port. This architecture ensures m
Inhaltszusammenfassung zur Seite Nr. 7
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Chapter 2 Pin Table 7-Port Table 2.1 7-Port Pin Table UPSTREAM USB 2.0 INTERFACE (3 PINS) USBDP0 USBDN0 VBUS_DET 7-PORT USB 2.0 INTERFACE (44 PINS) USBDP1 USBDN1 USBDP2 USBDN2 USBDP3 USBDN3 USBDP4 USBDN4 USBDP5 USBDN5 USBDP6 USBDN6 USBDP7 USBDN7 GR1/ GR2/ GR3/ GR4/ NON_REM0 NON_REM1 PRT_DIS0 PRT_DIS1 GR5 GR6 GR7 AM1/ AM2/ AM3 AM4/ GANG_EN MTT_EN LED_EN AM5 AM6 AM7 PRTPWR1 PRTPWR2 PRTPWR3 PRTPWR4 PRTPWR5 PRTPWR6 PRTPWR7 OCS1_N OCS2_N OCS3_N OCS4_
Inhaltszusammenfassung zur Seite Nr. 8
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Chapter 3 Pin Configuration 7-Port Hub Figure 3.1 7-Port 80-Pin TQFP Revision 2.3 (08-27-07) 8 SMSC USB2507 DATASHEET
Inhaltszusammenfassung zur Seite Nr. 9
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Chapter 4 7-Port Hub Block Diagram To EEPROM Pin or SMBus Upstream Upstream 24 MHz 1.8V Strapping 3.3V Master USB Data V Crystal Cap Options BUS SD SCL Internal V 1.8V Serial BUS Defaults PLL Interface Power Reg. Upstream Select Detect PHY SIE Controller Repeater TT TT TT Port ... #1 #2 #7 Controller Routing Logic Port #1 Port #7 Downstream OC Sense Downstream OC Sense ... PHY #1 Switch Driver PHY #7 Switch Driver LED Drivers LED Drivers Downstr
Inhaltszusammenfassung zur Seite Nr. 10
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Table 4.1 7-Port Hub Pin Descriptions (continued) NAME SYMBOL TYPE FUNCTION 7-PORT USB 2.0 HUB INTERFACE High-Speed USB USBDN[7:1] IO-U These pins connect to the downstream USB peripheral devices attached to the Hub’s ports. Data USBDP[7:1] USB Power PRTPWR[7:1] O12 Enables power to USB peripheral devices (downstream). Enable The active signal level of the PRTPWR7:1 pins is determined by the Power Polarity Strapping function of the PRTPWR_P
Inhaltszusammenfassung zur Seite Nr. 11
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Table 4.1 7-Port Hub Pin Descriptions (continued) NAME SYMBOL TYPE FUNCTION Port 4 Amber AM4/ I/O12 Amber indicator LED for port 4. Will be active low when LED support is enabled via EEPROM or SMBus. LED LED_EN & If the hub is configured by the internal default configuration, LED Enable this pin will be sampled at RESET_N negation to determine strapping option if LED support is enabled or disabled. Also, the active state of the LED will be
Inhaltszusammenfassung zur Seite Nr. 12
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Table 4.1 7-Port Hub Pin Descriptions (continued) NAME SYMBOL TYPE FUNCTION SERIAL PORT INTERFACE Serial Data/SMB SDA/SMBDATA IOSD12 (Serial Data)/(SMB Data) signal. Data Serial Clock/SMB SCL/SMBCLK/ IOSD12 (Serial Clock)/(SMB Clock) signal. This multifunction pin is read on the rising edge of RESET_N (see the applicable Clock CFG_SEL0 RESET_N timing table in Section 5.6.1) and will determine & the hub configuration method as described in Ta
Inhaltszusammenfassung zur Seite Nr. 13
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Table 4.3 Miscellaneous Pins (continued) NAME SYMBOL TYPE FUNCTION Analog Test ATEST/ AIO This signal is used for testing the analog section of the chip, and to enable or disable the internal 1.8v regulator. & REG_EN Internal 1.8V This pin must be connected to VDDA33 to enable the voltage internal 1.8V regulator, or to VSS to disable the internal regulator regulator. enable When the internal regulator is enabled, the 1.8V power pins mus
Inhaltszusammenfassung zur Seite Nr. 14
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Table 4.5 Buffer Type Descriptions (continued) BUFFER DESCRIPTION I/O12 Input/Output, 12mA IOSD12 Open drain….12mA sink with Schmitt trigger, and must meet I2C-Bus Specification Version 2.1 requirements. ICLKx XTAL Clock Input OCLKx XTAL Clock Output I-R RBIAS IO-U Defined in USB Specification. Note: Meets USB 1.1 requirements when operating as a 1.1-compliant device and meets USB 2.0 requirements when operating as a 2.0-compliant device. AIO
Inhaltszusammenfassung zur Seite Nr. 15
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Chapter 5 Functional Block Description 5.1 7-Port Hub SMSC’s USB 2.0 7-Port Hub is fully specification compliant to the Universal Serial Bus Specification Revision 2.0 April 27,2000 (12/7/2000 and 5/28/2002 Errata). Please reference Chapter 11 (Hub Specification) for general details regarding Hub operation and functionality. For performance reasons, the 7-Port Hub provides 1 Transaction Translator (TT) per port (defined as Multi-TT configuratio
Inhaltszusammenfassung zur Seite Nr. 16
Integrated USB 2.0 Compatible 7-Port Hub Datasheet 5.1.1.5 Port Indicators Controls the use of LED indicator for Port status information. See Section 11.5.3 of the USB 2.0 Specification for additional details. This field is set by the OEM using either the SMBus or EEPROM interface options. When using the internal default option, the LED_EN pin enables/disables LED Indicator support. 5.1.1.6 High-Speed Disable Allows an OEM to force the Hub to configure as a Full-Speed device only (i.e. High-Spee
Inhaltszusammenfassung zur Seite Nr. 17
Integrated USB 2.0 Compatible 7-Port Hub Datasheet 5.1.1.12 Non-Removable Device Informs the Host if one of the active ports has a permanent device that is undetachable from the Hub. (Note: The device must provide its own descriptor data.) This field is set by the OEM using either the SMBus or EEPROM interface options. When using the internal default option, the NON_REM[1:0] pins will designate the appropriate ports as being non- removable. 5.1.1.13 Self-Powered Port DISABLE During Self-Powered
Inhaltszusammenfassung zur Seite Nr. 18
Integrated USB 2.0 Compatible 7-Port Hub Datasheet 5.1.1.19 Self-powered Hub Controller Current When in Self-Powered configuration, Maximum current requirements of the Hub Controller in 2mA increments. This field is set by the OEM using either the SMBus or EEPROM interface options. 5.1.1.20 Bus-Powered Hub Controller Current When in Bus-Powered configuration, Maximum current requirements of the Hub Controller in 2mA increments. This field is set by the OEM using either the SMBus or EEPROM interf
Inhaltszusammenfassung zur Seite Nr. 19
Integrated USB 2.0 Compatible 7-Port Hub Datasheet 5.2.1.1 Implementation Characteristics Please refer to the MicroChip 24AA00 DataSheet for Protocol and Programming specifics. 5.2.1.2 Pull-Up Resistor The Circuit board designer is required to place external pull-up resistors (10KΩ recommended) on the SDA/SMBDATA & SCL/SMBCLK/CFG_SELO lines (per SMBus 1.0 Specification, and EEPROM manufacturer guidelines) to Vcc in order to assure proper operation. 5.2.1.3 I2C EEPROM Slave Address Slave address
Inhaltszusammenfassung zur Seite Nr. 20
Integrated USB 2.0 Compatible 7-Port Hub Datasheet Table 5.1 User-Defined Descriptor Data (continued) DEFAULT DEFAULT BYTE CFG CFG MSB: SIZE SELF BUS FIELD LSB (BYTES) (HEX) (HEX) DESCRIPTION Hub Controller E 1 64 64 Max Current (expressed in 2mA units). Max Current Bus-Powered Power-On F 1 32 32 Time until power is stable. Time 5.2.3.1 EEPROM Offset 1:0(h) - Vendor ID BIT NUMBER BIT NAME DESCRIPTION 15:8 VID_MSB Most Significant Byte of the Vendor ID. 7:0 VID_LSB Least Significant Byte of the
