Bedienungsanleitung Linksys NULL SR224G

Inhaltszusammenfassung zur Seite Nr. 1

24-Port 10/100
+ 1-Port Gigabit Switch
+ 1 miniGBIC
Use this guide to install:
SR224G
User Guide

Inhaltszusammenfassung zur Seite Nr. 2

COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2003 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. LIMITED WARRANTY Linksys warrants to the original end user purchaser (“You”) that, for a period of the product’s lifetime, (the “Wa

Inhaltszusammenfassung zur Seite Nr. 3

Table of Contents Chapter 1: Introduction r The 24-Port 10/100 + 1-Port Gigabit Switch + 1 miniGBIC Chapter 1: Introduction 1 The 24-Port 10/100 + 1-Port Gigabit Switch + 1 miniGBIC 1 This new Linksys rackmount switch delivers non-blocking, wire speed switch- Features 1 ing for your 10, and 100 megabit network clients, plus multiple options for con- necting to your network backbone. Twenty-four 10/100 ports wire up your Chapter 2: Getting to Know the 24-Port 10/100 workstations, while the integr

Inhaltszusammenfassung zur Seite Nr. 4

mini-GBIC The mini-GBIC (gigabit interface converter) port is a con- Chapter 2: Getting to Know the nection point for a mini-GBIC module, so the Switch can be uplinked via fiber to another switch. The mini-GBIC port is compatible with two types of modules, 850 nm and 1310 nm. 24-Port 10/100 + 1-Port Gigabit Switch + 1 miniGBIC Back Panel Port Front Panel LEDs and Ports Figure 2-2 The power port is located on the back panel of the Switch. Figure 2-1 (power) The power port is where you will conne

Inhaltszusammenfassung zur Seite Nr. 5

Connecting Network Devices Chapter 3: Connecting the 24-Port To connect network devices to the Switch, follow these instructions: 10/100 + 1-Port Gigabit Switch 1. Make sure all the devices you will connect to the Switch are powered off. + 1 miniGBIC 2. Connect a Category 5 Ethernet network cable to one of the numbered ports on the Switch. Overview our Network Layout This chapter will explain how to connect network devices to the Switch. For an example of a typical network configuration, see th

Inhaltszusammenfassung zur Seite Nr. 6

Placement Options Appendix A: Glossary There are two ways to physically install the Switch: 10BaseT - An Ethernet standard that uses twisted wire pairs.  set the Switch on its four rubber feet  mount the Switch in a standard-sized, 1U high rack. 100BaseTX - IEEE physical layer specification for 100 Mbps over two pairs of Category 5 UTP or STP wire. For rack-mounting, the Switch has four mounting holes located on each side. Place the Switch in the rack, and secure it with screws. 1000Base-T - P

Inhaltszusammenfassung zur Seite Nr. 7

Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet Appendix B: Specifications CSMA/CD network access method. Hub - The device that serves as the central location for attaching wires from Model Number SR224G workstations. Can be passive, where there is no amplification of the signals; or active, where the hubs are used like repeaters to provide an extension of the cable that connects to a workstation. Standards IEEE 802.3, 802.3u, 802.3x, 802.3ab Mbps (Megabits per second) - O

Inhaltszusammenfassung zur Seite Nr. 8

Appendix C: Warranty Information Appendix D: Contact Information BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE For help with the installation or operation of this 24-Port 10/100 + 1-Port FROM THE PRODUCT’S PACKAGING ON HAND WHEN CALLING. Gigabit Switch + 1 miniGBIC, contact Linksys Technical Support at one of the RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF phone numbers or Internet addresses below. PURCHASE. Sales Information 800-546-5797 (LINKSYS) IN NO EVENT SHALL LINKSYS’S LI

Inhaltszusammenfassung zur Seite Nr. 9

http://www.linksys.com © Copyright 2003 Cisco Systems, Inc. All Rights Reserved.