Inhaltszusammenfassung zur Seite Nr. 1
OWNER’S MANUAL
_________________
BAYTECH
REMOTE POWER CONTROL UNIT
FOR MODELS
RPC-2
RPC-2A
RPC-2 MD01
RPC-2 RDR
RPC-3
RPC-3A
RPC-5
BayTech Manual Publication #U140E125-03
July 1998
Inhaltszusammenfassung zur Seite Nr. 2
Copyright 1998 by Bay Technical Associates, Inc. BayTech, Telplex, LaserShare, Print Master and TRAN-X are registered trademarks of Bay Technical Associates, Inc. IBM, IBM PC, IBM PC/AT, IBM PC/XT are products and registered trademarks of International Business Machines Corporation. Hewlett-Packard LaserJet is a product and registered trademark of the . Hewlett-Packard Company PROCOMM PLUS is a product and registered trademark of Datastorm Technologies, Inc. ii
Inhaltszusammenfassung zur Seite Nr. 3
RPC SERIES OWNER’S MANUAL ABOUT THIS OWNER’S MANUAL ________________________________________________________________________________ ABOUT THIS OWNER’S MANUAL This document provides information required for installing and operating your Bay Tech equipment. It should allow the user to connect, power up, and access an applications menu where peripheral equipment can be controlled. We recommend reading this manual carefully, while placing special emphasis on correct cabling and configuration. If
Inhaltszusammenfassung zur Seite Nr. 4
RPC SERIES OWNER’S MANUAL ABOUT THIS OWNER’S MANUAL ________________________________________________________________________________ The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The informat
Inhaltszusammenfassung zur Seite Nr. 5
RPC-2 AND RPC-2A QUICK START......................................................................... 2 RPC-2 MD01 AND RPC-2 RDR QUICK START ....................................................... 5 RPC-3, RPC-3A, AND RPC-5 QUICK START.......
Inhaltszusammenfassung zur Seite Nr. 6
CHANGE OUTLET NAME.............................................................................. 34 RPC-3, RPC-3A, AND RPC-5 .................................................................................... 36 LOCAL ACCESS USING THE EIA-232 PORT ................................................... 37 REMOTE ACCESS USING THE NETWORK PORT.......................................... 37 OPERATION.......................................................................................
Inhaltszusammenfassung zur Seite Nr. 7
#$ ! #$
&' # $
&" #( vii
Inhaltszusammenfassung zur Seite Nr. 8
RPC SERIES OWNER’S MANUAL INTRODUCTION TO THE RPC SERIES ________________________________________________________________________________ INTRODUCTION TO THE REMOTE POWER CONTROL SWITCH (RPC) The BayTech RPC-Series is a full-featured AC power management solution that provides an easy way to control power of remote equipment. From your office or from anywhere, the RPC will TURN ON, TURN OFF, OR REBOOT remote equipment. There are six different RPC models. Four models operate at 115 VAC, 15 Amp.
Inhaltszusammenfassung zur Seite Nr. 9
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-2 AND RPC-2A) ________________________________________________________________________________ RPC SERIES QUICK START “Quick Start” is designed for users familiar with BayTech products who need a fast setup and familiarization. Detailed information on each of the functions and steps of operation and configuration may be found beginning at pages 19, 27, and 36 of this manual. Each “Quick Start” will discuss similar models. RPC-2 AND RPC-2A QUI
Inhaltszusammenfassung zur Seite Nr. 10
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-2 AND RPC-2A) ________________________________________________________________________________ If the status menu fails to appear, ensure the correct cables and adapters are being used and that they are connected properly. Also, verify the serial communication parameters are correctly configured. Controlling Receptacles To set or change the status of the receptacles, enter one of the following commands: ON n, OFF n, REBOOT n, where “n” is
Inhaltszusammenfassung zur Seite Nr. 11
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-2 AND RPC-2A) ________________________________________________________________________________ Change Password Default password is . The maximum field length is 8 alphanumeric characters. The password feature is case sensitive. Change Outlet Name Default Outlet Names are Outlet 1, Outlet 2, … The maximum field length is 10 alphanumeric characters. Enable/Disable Default setting is enabled. This setting prompts the user for a Yes or No wh
Inhaltszusammenfassung zur Seite Nr. 12
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-2 MD01 AND RPC-2 RDR) ________________________________________________________________________________ RPC-2 MD01 AND RPC-2 RDR QUICK START Using the 9FRJ45PC-1 adapter and the Local access using EIA-232 serial RJ08X007 (8-pin crossed) cable, connect the connection serial port of your computer to the RJ-45 port labeled “EIA-232.” Load serial port communications software. Set serial communications parameters to 9600 bps, 8 data bits, 1 stop b
Inhaltszusammenfassung zur Seite Nr. 13
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-2 MD01 AND RPC-2 RDR) ________________________________________________________________________________ Using the RJ04X007 (RJ-11) modular cable, connect either port labeled “LINE” on the RPC unit to the telco wall jack. Using another RJ04X007 (RJ-11) modular cable, connect the remaining port labeled “LINE” on the RPC unit to the port labeled “LINE” on the external modem. Using the 25MRJ45MD-8 adapter and the RJ08X007 (8-pin crossed) cable, c
Inhaltszusammenfassung zur Seite Nr. 14
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-2 MD01 AND RPC-2 RDR) ________________________________________________________________________________ Controlling Receptacles To set or change the status of the receptacles, enter one of the following commands: ON n, OFF n, REBOOT n, where “n” is the outlet number you want to command. Entering an outlet number of “0” sends the command to all outlets. Reboot only works on outlets which are in the “ON” condition. Type “CONFIG” from the RPC>
Inhaltszusammenfassung zur Seite Nr. 15
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-3, RPC-3A, AND RPC-5) ________________________________________________________________________________ RPC-3, RPC-3A AND RPC-5 QUICK START NOTE: The RPC-3, 3A and 5 are configured in a similar manner. This quick start will reference the RPC-3 menus. The only programming differences for the RPC-5 pertain to the number of receptacles shown in the menus (4 vice 8). NOTE: Inlet #1 supplies power to the logic of the RPC-5, this inlet must have pow
Inhaltszusammenfassung zur Seite Nr. 16
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-3, RPC-3A, AND RPC-5) ________________________________________________________________________________ RPC-3 Telnet Host Revision F 3.03, (C) 1998 Bay Technical Associates Unit ID: RPC3 RPC-3 Menu: 1) . . . Outlet Control 2) . . . Manage Users 3) . . . Configuration 4) . . . Unit Status 5) . . . Reset Unit 6) . . . Logout Enter Selection: If the main menu fails to appear, ensure the correct cables and adapters are being used and that they ar
Inhaltszusammenfassung zur Seite Nr. 17
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-3, RPC-3A, AND RPC-5) ________________________________________________________________________________ Change Password Default password is ; disabled. Password is case sensitive. Change Outlet From the User Management Menu, select List the number of the user to modify, followed by . Enter the number of the outlet(s) to which you want to give or remove access. If there is more than one outlet, enter the numbers, separated by commas.
Inhaltszusammenfassung zur Seite Nr. 18
RPC SERIES OWNER’S MANUAL RPC SERIES QUICK START (RPC-3, RPC-3A, AND RPC-5) ________________________________________________________________________________ Access Default password is ; disabled. NOTE : If user name and password are disabled (default), outlet users will have access to all admin functions. Outlets Outlet Status display – Default is enabled Command Confirmation – Default is enabled Outlet Power-up Delay – programmable elapse time before applying power to an outlet after unit
Inhaltszusammenfassung zur Seite Nr. 19
RPC SERIES OWNER’S MANUAL INSTALLATION ________________________________________________________________________________ INSTALLATION UNPACKING Compare the unit and serial number of the equipment you received to the packing slip located on the outside of the box. Log this information on the sheet on page 60. Inspect equipment carefully for damage that may have occurred in shipment. If there is damage to the equipment or if materials are missing, contact BayTech technical support at 228-467-8231
Inhaltszusammenfassung zur Seite Nr. 20
RPC SERIES OWNER’S MANUAL INSTALLATION ________________________________________________________________________________ POWER CAUTION: This unit is intended for indoor use only. Do not install near water or expose this unit to moisture. To prevent heat buildup, do not coil the power cord when in use. Do not use extension cords. Do not attempt to make any internal changes to the power source. Do not attempt to modify any portion or component of an RPC Series Unit unless specifically directe
