Inhaltszusammenfassung zur Seite Nr. 1
Server Intelligent Switch
SERVIS - 2
For PC/AT, Mac(USB)
FS-102ATL(NC14003-T256/L)
User’s Manual
Table of Contents
INTRODUCTION ............................................................................................................2
CHECKING THE CONTENTS OF THE PACKAGE.........................................................4
CHARACTERISTICS......................................................................................................4
COMPONENT NAMES AND THEIR
Inhaltszusammenfassung zur Seite Nr. 2
[ CAUTION ] 1) This product and document are the copyright of Fujitsu Component Ltd. Any unauthorized reprinting, copying, republishing, or modifications to this product or document is prohibited by law. 2) The details of this product and document are subject to revision without notice. 3) We are not responsible for any effects this product may have on other products regardless of the above statement. 4) If this product falls under any categories of restricted cargo and/or technology b
Inhaltszusammenfassung zur Seite Nr. 3
Introduction Thank you for buying the FS-102ATL (from here on, simply referred to as "the switch device"). Two consoles (monitor, keyboard or mouse) that up till now have been connected to individual hosts can be shared as a console pair by connecting two hosts to the switch device. The host can be easily selected by the Select Switch or from the keyboard. Safety instructions are provided to ensure the safe use of the switch device. Also, be sure to thoroughly read this User's Manu
Inhaltszusammenfassung zur Seite Nr. 4
● The internal voltage sometimes drops and prevents the switch device from operating depending on how it is used and its operating environment. If this happens, the LOW POWER LED on the front panel lights up. Connect the special AC adapter (option). ● Use the special AC adapter. Using an incompatible AC adapter will not only effect the operation of the switch device, but may also damage it. ● Correctly set each of the hosts matched to the keyboard/mouse on the console. The switch device ma
Inhaltszusammenfassung zur Seite Nr. 5
Checking the Contents of the Package When unpacking the switch device, make sure that all of the following parts are provided in the package. If the package does not contain all of the parts, immediately contact your agent. Keep the packing box (product box) in a safe place as it will be needed when sending the switch device in for repair. ● Main unit :1 ● User's Manual :1 ● AC adapter :1 ● AC code (for USA & for EC) :2 ● VGA Cable(1.8m) :2 ● Audio Cable (1.8m) :2 ● PS/2 Cable(1.
Inhaltszusammenfassung zur Seite Nr. 6
Component Names and Their 1. PC Select Switch Functions Press this switch to select the host. PCs with POWER LEDs out can also be selected if power is being supplied to the switch device (one or Front Panel more host is ON). 2. Select LED Lights up when the host is selected. 3. POWER LED Lights up when the host is ON. 4. LOW POWER LED The switch device monitors whether or not the power voltage is normal. Connect the special A
Inhaltszusammenfassung zur Seite Nr. 7
Installing the USB Bridge Software Software Installation Procedure Before attaching the switch device to the PCs, the following installation and setup steps must be performed: * The “Setup Program” referred to in this section is the “setup.exe” executable found on the supplied CD-ROM disk. 1. How the installation should proceed The switch device may be used after following the steps outlined in (1)~(3), below. Run the Setup Program on the two PCs to which the switch device is to be
Inhaltszusammenfassung zur Seite Nr. 8
Specify where the Setup Program should be installed. If the default installation location is to be accepted as-is, just click the [Next] button. * To specify a different folder, click the [Browse] button, then select the desired folder. The default installation folder is “C:\Program Files\USB\USB-USB Network Bridge v1.8.0.0”. When installing on Windows 2000, a [Digital Signature] dialog will appear next. Click the [Yes] button. When installing on Windows XP, a Windows logo test warning
Inhaltszusammenfassung zur Seite Nr. 9
When the reboot screen appears, click the [Finish] button. Rebooting the PC completes the installation of the required drivers. After rebooting, connect the switch device. (After connecting the switch device, the [new hardware detection wizard] may start up, in which case select [automatically install the required software] to install the drivers.) 3. Setting up the PC Setting up file, folder (drive, including external devices) and printer sharing. (Refer to the manuals provided with
Inhaltszusammenfassung zur Seite Nr. 10
Turning on [File and printer sharing for Microsoft Networks] Click the [File and Print Sharing] button, and make sure that the [I want to be able to give others access to my files] and [I want to be able to allow others to print to my printer(s)] check boxes are checked. Check that [File and printer sharing for Microsoft Networks] has been added to the list of installed network components. Setting the Computer name and Workgroup On the [Identification] tab, enter a [Co
Inhaltszusammenfassung zur Seite Nr. 11
Setting up drive and folder sharing Double-click the Windows [Explorer] or [My Computer] icon. Right-click the icons of any drives (or folders) that you want to share, then select [Sharing] from the popup menu. On the Sharing Properties screen shown below, check the [Shared As] check-box, adjust the [Share Name], [Comment], [Access Type] and [Passwords] settings as necessary, then click the [OK] button. Share Name: enter the name that you wish to be displayed on the PC accessing the
Inhaltszusammenfassung zur Seite Nr. 12
(4) Click the [Browse] button, find and select the printer that you wish to share, then click the [Next] button. (5) The applicable printer driver is enabled, finishing the shared printer setup. You may need to install the applicable printer driver if it has not yet been installed. (Refer to the manuals provided with the PC or OS for further details of the setup procedure) 4. Accessing networked computers (All file transfers or other access between networked computers should be perform
Inhaltszusammenfassung zur Seite Nr. 13
6. Troubleshooting the installation Checking the USB controller and network adapter Select [Start] -> [Settings] -> [Control Panel], then double-click the [System] control panel icon. Double-click the [Universal serial bus controller] item (toward the bottom of the device list). Check that the “USB-USB Network Bridge Driver” shows up toward the bottom of the list of controllers. Similarly, check that the “USB-USB Network Bridge” appears toward the bottom of the [Network adapters] l
Inhaltszusammenfassung zur Seite Nr. 14
Connecting the PCs 1. Start by turning the PCs off. (1) Speaker 2. 1) Connect the KB/Mouse connector of the 1st host to the KB/Mouse connector on the switch device. Be sure to connect the host side first, then the switch device. (Connect (2).) This connection is not required when the (2) (4) (3) (5) switch device is to be used only on the USB port. 2) Connec
Inhaltszusammenfassung zur Seite Nr. 15
Installing the USB HUB, USB Keyboard and USB Mouse drivers Initial setup is required when connecting with a USB port. The required drivers are contained in OS. Therefore, it is not necessary to newly prepare. The setup procedure for Windows98 Turn the PC on, and wait for Windows 98 to start. Connect the switch device to the host (refer to page 5 for details). When the [Add New Hardware Wizard] window appears, click the [Next] button. Select [Search for the best driver for
Inhaltszusammenfassung zur Seite Nr. 16
After searching for and finding the required driver, the following screen should appear. Click the [Next] button. When the driver installation has completed, the following screen should appear. Click the [Finish] button. This process will need to be repeated three times, once each for the keyboard, mouse and HUB. This completes the initial setup procedure. Hereafter the devices should be automatically recognized and usable whenever the USB cable is connected. . The setu
Inhaltszusammenfassung zur Seite Nr. 17
FS-102ATL Application Examples File Sharing Use of the Network Sharing Service provided by the Microsoft OS allows data to be shared and files copied between the two PCs. [Required Software] Microsoft Network [Acquisition Method] Standard with OS Internet Connection Sharing Connecting to the Internet via a dialup connection or similar (this example uses an internal modem) Windows 98SE and ME allow a single internet connection to be shared by multiple
Inhaltszusammenfassung zur Seite Nr. 18
Printer & Storage Device Sharing Sharing of USB devices connected to the FS-102ATL allows them to be used by both PCs. [Required Software] Microsoft Network [Acquisition Method] Standard with OS Printer MO/CD-R(W) How to Select the Host PC There are two ways of selecting the host: by the Select switch on the switch device or from the keyboard (Hot Key mode). You can also select an unconnected port or the port of a host that is OFF. If a selected PC is t
Inhaltszusammenfassung zur Seite Nr. 19
Key layout diagram ASCII keyboard for Mac (PS/2) Standard layout (DIP switch 5,6) The functions of the keys with thick borders are changed. The setup of the DIP switch is set to Mac. (Refer to page 18.) Note that the crossed out key is disabled. Extended layout (DIP switch 7) key and key can be replaced by setup. (Refer to page 18.) Note that the crossed out key is disabled. 18
Inhaltszusammenfassung zur Seite Nr. 20
About the Special AC Adapter When the switch device is connected to the USB port for use, the special AC adapter must be connected. However, when the switch device is used only on the keyboard/mouse port (PS/2 port), the configuration is designed so that this special AC adapter is not required. However, connecting power consuming keyboards and mice may drop the power voltage. In such cases, the LOW POWER LED turns on (Orange); connect the special AC adapter. 1. Use only the AC adapters s
