Bedienungsanleitung Extron electronic P/N 68-412-02

Inhaltszusammenfassung zur Seite Nr. 1

Hughes Installation Configuration and Connections
SYSTEM 4

PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: HUGHES
Included Communications Adapter(s):
Quantity Part Number Description
1 26-467-01 ADP, UNV, “A”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT

Inhaltszusammenfassung zur Seite Nr. 2

Hughes Installation Configuration and Connections Connecting System 4
 to Hughes/JVC Projectors If the System 4
 is already configured for a Hughes/JVC projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4
’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4
 is already set up for the Hughes/JVC projector. Apply power t

Inhaltszusammenfassung zur Seite Nr. 3

Hughes Installation Configuration and Connections 6. Plug the 15-pin HD connector of the Projector Communications Extension cable (CC 50' or CC 100') into the PJ Comm port on the System 4. The other end has a 9-pin female connector. Plug this end into the other 9-pin male D connector on the HU COM adapter. ______ Secure all of the connector screws. 7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable onto the System 4 output and those on the other end onto the ma

Inhaltszusammenfassung zur Seite Nr. 4

Hughes Installation Configuration and Connections System 4
- Hughes/JVC Model HJT 100/200 Series Connections Use the illustration below as a guide when connecting the System 4
 to a Hughes/JVC HJT 100/200 projector. Refer to Hughes documentation to continue the installation. Hughes HJT 200 Projector Terminal In Control Out Port A (Port B) UNV ADP "A" "A" 26-467-01 3, 4, or 5 BNC Cable CC 50' Connecting the System 4
 to a Hughes/JVC HJT 200 Projector ____________ In a rack mount, do NOT all

Inhaltszusammenfassung zur Seite Nr. 5

Hughes Installation Configuration and Connections Special Instructions for the HJT Model 100/200 Series The projector documentation provides instructions on how to set up and configure the Model 100/200 Series Projector for proper operation with the System 4
. The baud rate for the Extron switchers is 19200. Since Port A is locked to a baud rate of 9600, Port B should be used for Extron Switchers. The projector port assignment must be selected and the VIC channel assignment must be edited for a

Inhaltszusammenfassung zur Seite Nr. 6

Hughes Installation Configuration and Connections Connecting System 4
 to Hughes-JVC DILA G1000/G10 Projectors If the System 4
 is already configured for a Hughes-JVC DILA projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4
’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4
 is already set up for the Hughes-JVC DILA

Inhaltszusammenfassung zur Seite Nr. 7

Hughes Installation Configuration and Connections 5. The Hughes Adapter has two 9-pin connectors, one male and one female. Plug the 9-pin female connector onto the 9-pin male marked “Control Out” (Port B) on the Hughes projector back panel. 6. Plug the 15-pin HD connector of the Projector Communications Extension cable (CC 50' or CC 100') into the PJ Comm port on the System 4
. The other end has a 9-pin female connector. Plug this end into the other 9-pin male D connector on the HU COM Adapter.