Bedienungsanleitung Extron electronic s68-392-02

Inhaltszusammenfassung zur Seite Nr. 1

User’s Manual
DISPLAY
POWER
VCR DVD Laptop
VOLUME
MAX/
MIN
Extron
MLC 206
MediaLink Controller
Extron Projector
Extron IR Broadcaster
MLC
IR Broadcaster
System Switcher and MediaLink Accessory
68-392-02 Rev. B
Printed in the USA
02 02

Inhaltszusammenfassung zur Seite Nr. 2

Introduction The IR Broadcaster (part #60-272-02) The Extron Infrared Broadcaster transmits IR signals that have been “learned” by an Extron system switcher or Extron MediaLink Controller (MLC) and that are associated with the front panel functions. This allows other IR controlled devices in the room to receive the signal put out by the Broadcaster. Refer to the appropriate switcher’s or controller’s user’s manual for IR learning procedures. Pressing buttons on the system switcher’s or control

Inhaltszusammenfassung zur Seite Nr. 3

1 2 3 4 5 6 7 8 9 10 CONTROL DISP DISP ROOM ROOM MODE COLOR TINT BRIGHT CONT DETAIL PWR MUTE 1 2 ADJUST VOLUME MENU NEXT 1234567 INPUT 7 DISPLAY IR VIDEO VIDEO S-VIDEO S-VIDEO AUDIO COMPUTER RX LEARN TX LR RX LR SYSTEM 7SC Extron System 7SC Tip (Signal) White = Signal Sleeve (Gnd) IR Emitter Black = Ground Connecting an IR Broadcaster, IR Emitter, and a system switcher Using a signal with a carrier signal For most applications, a signal that already has a carrier frequency may be used with the I

Inhaltszusammenfassung zur Seite Nr. 4

Installation and Operation, cont’d DIP Switch Settings for IR Broadcaster-Generated Carrier Frequencies (DIP switch 9: closed. DIP switch 10: not used.) Closed = up, Closed = up, Closed = up, Freq. Freq. Freq. Open = down, Open = down, Open = down, (kHz) (kHz) (kHz) 1234567 8 1234567 8 1234567 8 13,400.00 326.80 165.40 6,700.00 319.00 163.40 4,466.70 311.60 161.40 3,350.00 304.55 159.53 3,350.00 304.50 159.50 2,680.00 297.80 157.60 2,233.30 291.30 155.80 1,914.30 285.10 154.00 1,675.0

Inhaltszusammenfassung zur Seite Nr. 5

DIP Switch Settings for IR Broadcaster-Generated Carrier Frequencies (DIP switch 9: closed. DIP switch 10: not used.) Closed = up, Closed = up, Closed = up, Freq. Freq. Freq. Open = down, Open = down, Open = down, (kHz) (kHz) (kHz) 1234567 8 1234567 8 1234567 8 110.70 56.78 35.28 109.80 55.83 34.90 108.90 54.93 34.53 108.10 54.03 34.18 108.08 53.18 33.85 107.20 52.35 33.50 106.30 51.55 33.18 105.50 50.75 32.85 104.70 50.00 32.53 104.70 49.28 32.20 12 34 5678 1 23 45 6 7 8 1 2 3 4 5 6

Inhaltszusammenfassung zur Seite Nr. 6

Installation and Operation Wiring tip-ring-sleeve and tip-sleeve connectors The illustration below shows how to wire a 3.5 mm stereo-style (tip- ring-sleeve) connector for the IR Broadcaster voltage, signal, and ground wires to connect the System Switcher or MLC to the IR Broadcaster. 1 Unscrew cover. 5 Solder 3 wires. 2 Locate components. 6 Bend tabs up over cable insulation. Sleeve (Gnd) 3 Slide cover and heat shrink Tip (+12V) Ring over cable. Tip 7 Slide heat shrink over exposed wires,

Inhaltszusammenfassung zur Seite Nr. 7

1/4” (0.6 cm) of insulation from each wire. Do not solder the tips. Insert each wire into the correct position on the captive screw connector, and tighten each screw. See the diagrams below. To pass through an IR signal that includes a carrier signal, connect the signal wire to the pin designated for carrier and signal. If you want the IR Broadcaster to generate the carrier signal, connect the signal wire to the pin designated for signal only. COMM A Signal only Sleeve (Gnd) B Gnd Tip (+12V)

Inhaltszusammenfassung zur Seite Nr. 8

Extron’s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within th