Inhaltszusammenfassung zur Seite Nr. 1
MONO CHANNEL CLASS "D"
AUTOMOTIVE AMPLIFIER
D900.1 / D1700.1 / D3000.1
INSTRUCTION MANUAL
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
CONGRATULATIONS ON YOUR PURCHASE Your new high fidelity mono block amplifier is designed to deliver maximum enjoyment and one year of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help insure trouble free installation. FEATURES • Class ''D'' Technology • 1 Ohm Stable • Spec Audiophile Grade Components • High Efficiency PWM Power Supply - Multi-stranded power toroid - Tow toroidal core - MOSFE
Inhaltszusammenfassung zur Seite Nr. 4
INSTALLATION MOUNTING: 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVER use the amplifier as a template for drilling. It is very easy to damage the amplifier surface in this manner. 3. Remove amplifier. Drill four 3.5 m/m holes into mounting surface. If you want to mount the ampl
Inhaltszusammenfassung zur Seite Nr. 5
SPEAKER WIRING The Class "D" amplifier is a SINGLE CHANNEL dedicated subwoofer amplifier. Unlike other amplifiers, the Class "D" operates as a single channel and cannot be bridged. Don't be fooled by the outputs. Two outputs are used strictly for convenience and are paralleled internally on the amplifier. This means that if both outputs are used with one driver each, the amplifier sees the same load as if the same drivers are connected to only one output terminal. See diagram below. SPEA
Inhaltszusammenfassung zur Seite Nr. 6
MONO BRIDGED MASTER SLAVE Master Amplifier MASTER SLAVE L 6V 0.2V 50Hz 250Hz 0dB 12dB GAIN L.P.F BASS REMOCON SLAVE R BOOST LINE INPUT FROM MASTER SLAVE RADIO Slave Amplifier MASTER SLAVE L 6V 0.2V 50Hz 250Hz 0dB 12dB L.P.F BASS REMOCON SLAVE GAIN R BOOST LINE INPUT WIRING SUBWOOFERS (DUAL AMPS) When using dual amplifiers to power one subwoofer, the Positive terminal of the Subwoofers voice coil is connected the positive terminal of the MASTER Amplifier and the Negative terminal of the Subwoof
Inhaltszusammenfassung zur Seite Nr. 7
MONO BRIDGED Master SPEAKER FUSE POWER +12V REM GND Amplifier ON PROTECT Using a lead wire of 8 gauge or bigger connect from the master Amp's negative(-) speaker terminal to the slave Amp's negative(-) speaker terminal. SPEAKER FUSE POWER +12V REM GND Slave ON Amplifier PROTECT BATTERY VIA FUSE CHASSIS GROUND REMOTE TURN ON (OPTION) TWO AMPLIFIER/ ONE SUBWOOFER (SINGLE VOICE COIL)CONFIGURATION Master SPEAKER FUSE POWER +12V REM GND Amplifier ON PROTECT SPEAKER FUSE POWER +12V REM GND Slave
Inhaltszusammenfassung zur Seite Nr. 8
MONO BRIDGED (OPTION) FOUR AMPLIFIER/ ONE SUBWOOFER (DUAL VOICE COIL)CONFIGURATION Master SPEAKER FUSE POWER +12V REM GND Amplifier ON PROTECT Voice Voice Coil1 Coil2 SPEAKER FUSE POWER +12V REM GND Slave ON Amplifier PROTECT Master SPEAKER FUSE POWER +12V REM GND Amplifier ON PROTECT SPEAKER FUSE POWER +12V REM GND Slave ON Amplifier PROTECT 6
Inhaltszusammenfassung zur Seite Nr. 9
POWER SUPPLY CONNECTIONS The Class "D" amplifier is designed to work within 10 to 16 volts DC. Before any wires are connected, the vehicle's electrical system should be checked for correct voltage supply with the help of a voltmeter. First check the voltage at the battery terminals with the ignition in the off position. The voltmeter should read no less than 12 volts. Next, check the battery with the engine running between 1500 and 2000 rpm. The voltmeter should now read between 13.5 and
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION 1 2 3 4 5 6 7 MASTER SLAVE L 6V 0.2V 50Hz 250Hz 0dB 12dB GAIN L.P.F BASS REMOCON SLAVE R BOOST LINE INPUT 1. RCA Input Jacks 2. Input Level Control 3. Low Pass Frequency 4. Bass Boost 5. Remote Control Jack 6. Master/Slave Switch 7. Slave Input Jack Control and Crossover 1. RCA Input Jacks - Low level-high impedance inputs. Use high quality RCA cables designed for mobile applications. 2. Input Level Control - Adjust the input level for the mar
Inhaltszusammenfassung zur Seite Nr. 11
FRONT/REAR PANEL MASTER SLAVE L 6V 0.2V 50Hz 250Hz 0dB 12dB GAIN L.P.F BASS REMOCON SLAVE R BOOST LINE INPUT D900.1, D1700.1, D3000.1 SPEAKER FUSE POWER 25A 25A 25A +12V REM GND ON PROTECT D900.1 D900.1 SPEAKER FUSE POWER 30A 30A 30A +12V REM GND ON PROTECT D1700.1 D1700.1 SPEAKER POWER +12V REM GND ON PROTECT D3000.1 D3000.1 9
Inhaltszusammenfassung zur Seite Nr. 12
TROUBLE SHOOTING GUIDE. This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly. SYMPTOM PROBABLE CAUSE SOLUTION No Audio Low or N.C Remote Check remote turn-on voltage at Turn-on connections amp and head unit Blown Fuse Replace with new fa
Inhaltszusammenfassung zur Seite Nr. 13
SPECIFICATION AMPLIFIER D900.1 D1700.1 D3000.1 RMS POWER / 1 ohm @ 1% T.H.D 900W x 1 1700W x 1 3000W x 1 2 ohms @ 0.05% T.H.D 650W x 1 1000W x 1 2000W x 1 4 ohms @ 0.05% T.H.D 350W x 1 500W x 1 1000W x 1 Efficiency / Typical @ 4 ohms 90% 90% 90% MIN RATE @ 1 ohm 79% 79% 79% Bandwidth ±1dB 10Hz ~ 250Hz 10Hz ~ 250Hz 10Hz ~ 250Hz Signal To Noise Ratio ('A' WTD) >100dB >100dB >100dB Damping Factor 150 150 150 Input Sensitivity 200mV ~ 6V 200mV ~ 6V
Inhaltszusammenfassung zur Seite Nr. 14
Inhaltszusammenfassung zur Seite Nr. 15
Inhaltszusammenfassung zur Seite Nr. 16
Interfire Audio, Inc. Santa Fe Springs, CA 90670 www.interfireaudio.com Printed in Korea
