Inhaltszusammenfassung zur Seite Nr. 1
AT-FS708LE
Fast Ethernet Switch
Version 2
Installation Guide
PN 613-50636-00 Rev A
Inhaltszusammenfassung zur Seite Nr. 2
Copyright © 2004 Allied Telesyn, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn, Inc. reserves the right to make changes in specifications and other information containe
Inhaltszusammenfassung zur Seite Nr. 3
Electrical Safety and Emission Statement Standards: This product meets the following standards. U.S. Federal Communications Commission DECLARATION OF CONFORMITY Manufacture Name: Allied Telesyn, Inc. Manufacture Address: 960 Stewart Drive, Suite B Sunnyvale, CA 94086 USA Manufacture Telephone: 408-730-0950 Declares that the product: Fast Ethernet Switch Model Number: AT-FS708LE Version 2 This product complies with FCC Part 15, Class B Limits: This device complies with part 15 of the FCC Rules
Inhaltszusammenfassung zur Seite Nr. 4
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules. Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Re
Inhaltszusammenfassung zur Seite Nr. 5
AT-FS708LE Installation Guide Vigtigt: Tillæg A indeholder oversatte sikkerhedsadvarsler, der vedrører installation af dette udstyr. Når De ser symbolet , skal De slå op i tillæg A og finde de oversatte sikkerhedsadvarsler i Deres eget sprog. Belangrijk: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van deze apparatuur. Wanneer u de ziet, raadpleeg Appendix A voor vertaalde veiligheidsinstructies in uw taal. Important: L'annexe A contient les instructions de s
Inhaltszusammenfassung zur Seite Nr. 6
Inhaltszusammenfassung zur Seite Nr. 7
Table of Contents Electrical Safety and Emission Statement ....................................3 Welcome to Allied Telesyn.........................9 Where to Find Web-based Guides ..................9 Document Conventions ...................................9 Contacting Allied Telesyn..............................10 Online Support ........................................10 E-mail and Telephone Support...............11 Returning Products.................................11 For Sales or Corporate I
Inhaltszusammenfassung zur Seite Nr. 8
Cascade Topology ....................................23 Planning the Installation...............................24 Verifying the Package Contents .............24 Selecting a Site ........................................25 Reviewing Safety Guidelines ..................26 Installing the Unit on a Desktop ...................28 Installing the Unit on a Wall.........................29 Warranty Registration ...................................31 Troubleshooting .........................................
Inhaltszusammenfassung zur Seite Nr. 9
Welcome to Allied Telesyn This guide contains instructions on how to install an Allied Telesyn AT-FS708LE Fast Ethernet Switch. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com offers you an easy way to access the most recent documentation, software, and technical information for all of our products. For product guides, select “Support & Services” from our web site. Document Conventions This guide uses the following conventions: Note Notes provide additi
Inhaltszusammenfassung zur Seite Nr. 10
Caution Cautions informs you that performing or omitting a specific action may result in equipment damage or loss of data. Warning Warnings informs you that performing or omitting a specific action may result in bodily injury. Contacting Allied Telesyn This section provides Allied Telesyn contact information for technical support as well as sales or corporate information. Online Support You can request technical support online by accessing the Allied Telesyn Knowledge Base from the foll
Inhaltszusammenfassung zur Seite Nr. 11
AT-FS708LE Installation Guide E-mail and Telephone Support For Technical Support via E-mail or telephone, refer to the Support & Services section of the Allied Telesyn web site: http://www.alliedtelesyn.com. Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense. To obtain a RMA number, contact Allied Telesyn’s Techn
Inhaltszusammenfassung zur Seite Nr. 12
Inhaltszusammenfassung zur Seite Nr. 13
AT-FS708LE Fast Ethernet Switch Overview The AT-FS708LE unit is a 10Base-T/ 100Base-TX Fast Ethernet Switch. The unit provides you with a simple, cost-effective solution for Ethernet switching between end- nodes operating at either 10 or 100 Mbps. Figure 1 and Figure 2 show the front and back panels of the switch. 100M 9-12V DC + 10BASE-T/100BASE-TX 8 PORT FAST ETHERNET SWITCH LNK/ACT PWR FDX 1 2 3 4 5 67 8 DC Power Port LEDs Connector Figure 1 Front Panel 13 _
Inhaltszusammenfassung zur Seite Nr. 14
8x 7x 6x 5x 4x 3x 2x 1x Figure 2 Back Panel Key Features The AT-FS708LE Ethernet Switch has the following features: ❑ LEDs for unit and port status ❑ 8 Auto-Negotiating 10/100 Mbps twisted pair ports with RJ-45 connectors ❑ Auto MDI/MDI-X on all ports ❑ IEEE 802.3 and IEEE 802.3u compliant ❑ Store and forward switching mode ❑ MAC address table capacity of up to 4,000 entries ❑ IEEE 802.3x flow control in full-duplex operation and back pressure flow control in half-duplex operation ❑ Extern
Inhaltszusammenfassung zur Seite Nr. 15
AT-FS708LE Installation Guide Status LEDs Refer to Table 1 for a description of the device LEDs. Table 1 LED Functions LEDs Color Description PWR Green Indicates the switch is receiving power. 100M Green Indicates the port is operating at 100 Mbps. OFF Indicates the port is operating at 10 Mbps. LNK/ACT Green Indicates a valid physical link on the port. Blinking Indicates data is being transmitted or received on the port. FDX Green Indicates the port is operating in full-duplex mode.
Inhaltszusammenfassung zur Seite Nr. 16
Power Supply The AT-FS708LE Ethernet Switch uses an external power adapter that comes standard with the unit. Store and Forward The AT-FS708LE switch uses store and forward as the method for receiving and transmitting frames. When an Ethernet frame is received on a switch port, the switch does not retransmit the frame out the destination port until it has received the entire frame and stored the frame in a port buffer. It then examines the frame to determine if it is a valid frame. Inv
Inhaltszusammenfassung zur Seite Nr. 17
AT-FS708LE Installation Guide end-node to stop transmitting data to allow the slower end-node to catch up. An example of this would be when a server operating at 100 Mbps is sending data to a workstation operating at only 10 Mbps. How a switch signals an end-node to stop transmitting data differs depending on the speed and duplex mode of the end-node and switch port. A twisted pair port operating at 100 Mbps port and half-duplex mode stops an end-node from transmitting data by forcing a
Inhaltszusammenfassung zur Seite Nr. 18
The AT-FS708LE supports TX Flow Control only. This means a PAUSE packet will be transmitted to the end-node connection if it receives data faster than it can switch the packets. The AT-FS708LE does not support RX Flow Control, however, and it will not respond to PAUSE packets sent to it by an end-node. Twisted Pair Ports The AT-FS708LE switch has eight 10Base-T/ 100Base-TX twisted pair ports. Each twisted pair port features a RJ-45 connector. The maximum operating distance for the twiste
Inhaltszusammenfassung zur Seite Nr. 19
AT-FS708LE Installation Guide port on the switch and the end-node are operating at the same speed and that they are communicating at the highest possible common speed of the devices. Duplex Mode Duplex mode refers to the way an end-node sends and receives data on the network. An end-node can operated in either half- or full- duplex mode depending on its capabilities. An end-node that is operating in half-duplex mode can either send data or receive data, but it cannot do both at the same
Inhaltszusammenfassung zur Seite Nr. 20
Note Since the AT-FS708LE ports operate in Auto-Negotiate mode only, the end-nodes connected to the AT-FS708LE must also be configured to operate in the Auto- Negotiate mode. If an end-node is configured to a specific duplex in a manual mode, it will not respond to the Auto-Negotiate protocol from the AT-FS708LE. (The speed is determined from the link pulses, however, so the speed is always detected correctly.) As a result, the AT-FS708LE port setting will end up at half-duplex. If th
