Inhaltszusammenfassung zur Seite Nr. 1
TM
Volition
Network Solutions
TM
VOL-1081
Fast Ethernet
Mini-switch 8+1
User Guide
ÿÿ Innovation
ÿÿ
Inhaltszusammenfassung zur Seite Nr. 2
This page left blank intentionally Page 2
Inhaltszusammenfassung zur Seite Nr. 3
Contents 1. Introduction...................................................................................................... 4 Figure 1-1. The VOL-1081 Fiber Switch .........................................................................4 Features ...............................................................................................................................4 2. Hardware Description...................................................................................... 5 Front Pa
Inhaltszusammenfassung zur Seite Nr. 4
1. Introduction The VOL-1081 Mini-switch is a compact desktop size switch that is ideal for small office or home office networks. It provides wire-speed, Fast Ethernet switching offering high- performance at low-cost. Figure 1-1. The VOL-1081 Fiber Switch ÿ The VOL-1081 Mini-switch provides 8 switched N-Way 10/100 Mbps RJ-45 Ethernet ports and one 100Base-FX VF-45™ fiber port. ÿ The Switch automatically detects the speed of the remote device to allow use of 10 and 100Mbps devices. ÿ The Switc
Inhaltszusammenfassung zur Seite Nr. 5
2. Hardware Description The VOL-1081 Mini-switch is a compact switch with 8x 10/100 N-way UTP switch ports plus one 100Base-FX fiber port. Front Panel ÿ The Front Panel of the VOL-1081 Mini-switch consists of 8x 10/100 N-way UTP switch ports (automatic MDI/MDIX), one 100Base-FX fiber port and one Dip-switch to select fiber port full-duplex or half-duplex mode. The LED indicators are also located on the front panel of the switch. LED VF-45 Connector RJ-45 Connectors indicators 100Base-FX port 10
Inhaltszusammenfassung zur Seite Nr. 6
LED Indicators ÿ The following table describes the LED status and description. The LEDs provide a real-time indication of system conditions. LED Status Color Description Power On Green Power On On Green The port is operating at the speed of 100Mbps. 100 Mb Off In 10Mbps mode or no device attached On Green The port is successfully connecting with the device. Lnk / Act Blinks The port is receiving or transmitting data. Off No device attached. On Yellow The port is operating in Full-duplex mode. F
Inhaltszusammenfassung zur Seite Nr. 7
Desktop Installation ÿ Set the Switch on a clean, smooth, level, and sturdy surface with a power outlet nearby. ÿ Make sure there is enough clearance around the Switch to allow attachment of cables, power cord and air circulation. Attaching Rubber Feet ÿ Make sure the surface on the bottom of the Switch is grease and dust free. ÿ Remove adhesive backing from the rubber feet and apply them to each corner on the bottom of the Switch, to minimize shock and vibration. Power On ÿ Connect the pow
Inhaltszusammenfassung zur Seite Nr. 8
3. Network Application This section provides an example of network topology in which the Switch is used. In general, the VOL-1081 Mini-switch is designed to be used as a desktop or segment switch. You can use the VOL-1081 Mini-switch to connect PCs, workstations, and servers to each other by connecting these devices directly to the Switch. The Switch automatically learns node address, which are subsequently used to filter and forward all traffic based on the destination address. Desktop Applicat
Inhaltszusammenfassung zur Seite Nr. 9
4. Trouble Shooting This troubleshooting section is intended to help you solve the most common problems on the VOL-1081 Fiber Switch. The Switch can be easily monitored through panel indicators to assist in identifying problems. This section describes common problems you may encounter and where you can find possible solutions. Diagnosing with the LED Indicators Link If the Lnk / Act indicator does not light up after making a connection check whether the network interface (e.g., a network adapter
Inhaltszusammenfassung zur Seite Nr. 10
5. Technical Specifications - VOL-1081 Mini-switch Interfaces and Cabling Copper Connector RJ-45 / 8 ports Impedance 100 ohm Network Cables and UTP - 10Base-T: 2-pair Cat. 3, 4, 5 cable (100m), Distances UTP - 100Base-TX: 2-pair Cat. 5 cable (100m), EIA/TIA-568 100-ohm STP (100m) Fiber Connector VF-45™ / 1port Source, Wavelength LED, 1300 nm Optical budget 11dB min. (62.5/125 um fiber) 7dB min. (50/125 um fiber) Sensitivity -31dBm min. Network Cables and 100Base-FX: 50, 62.5/125 micron multi-mod
Inhaltszusammenfassung zur Seite Nr. 11
Power requirements AC Input 100 to 240 Volts AC, 50 to 60Hz Power consumption Max. 12 Watts Physical and Environmental Specifications Dimensions 250 x 132 x 37 mm L x W x H, (9.84 x 5.19 x 1.47 inches) Switch Weight Switch 1.01 kg (2.2 lbs.) Temperature Operating 0to45°C(32to113°F) Storage -40to70°C(-40to158°F) Humidity Operating/Storage 10 to 90% non-condensing 6.0 Agency Approvals Electromagnetic and Safety Approvals EMI FCC Class B CE Mark Safety UL 1950, cUL FCC Statement This equipment has
Inhaltszusammenfassung zur Seite Nr. 12
3M, Volition, VF-45, and the “dot wave” symbol are trademarks of 3M Important Notice Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Warranty; Limited Remedy; Limited Liability This product will be free from defects in material and manufacture for a period of one year from the date of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
