Inhaltszusammenfassung zur Seite Nr. 1
®
3Com Switch 8800 Family
Installation Guide
Switch 8807
Switch 8810
Switch 8814
www.3Com.com
Part No. 10015593, Rev. AB
Published: June, 2007
Inhaltszusammenfassung zur Seite Nr. 2
3Com Corporation Copyright © 2006-2007, 3Com Corporation. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without 350 Campus Drive written permission from 3Com Corporation. Marlborough, MA 3Com Corporation reserves the right to revise this documentation and to make changes in content from time to time USA 01752-3064 without obligation on the part of 3Com
Inhaltszusammenfassung zur Seite Nr. 3
CONTENTS ABOUT THIS GUIDE Conventions 5 Related Documentation 6 About this Document 6 1 PRODUCT OVERVIEW Preface 7 General Architecture 10 Fabric Modules 17 System Specifications 24 Software Features 25 2 I/O AND APPLICATION MODULES Overview 29 3C17511 1-port 10GBASE-X (XENPAK) 29 3C17512 2-port 10GBASE-X (XFP) Module 30 3C17513 12-port 1000BASE-X (SFP) Module 31 3C17514 24-port 1000BASE-X (SFP) Module 32 3C17516 24-port 10/100/1000BASE-T Modul
Inhaltszusammenfassung zur Seite Nr. 4
Examining Installation Site 50 Installation Tools 52 4 SWITCH INSTALLATION Confirming Installation Preparation 53 Installation Flow 53 Mounting the Switch in User-Supplied Cabinet 54 Connecting PGND Wire and Power Cord 59 Installing Cabling Rack 64 Installing Fan Tray 64 Installing PoE Lightning Protection Box 65 Installing I/O modules 66 Connecting Interface Cables 67 Cable Routing Recommendations 70 Cable Management 70 Verifying the Installat
Inhaltszusammenfassung zur Seite Nr. 5
ABOUT THIS GUIDE ® This guide describes the 3Com Switch 8800 and how to install hardware, configure and boot software, and maintain software and hardware. This guide also provides troubleshooting and support information for your switch. This guide is intended for Qualified Service personnel who are responsible for configuring, using, and managing the switches. It assumes a working knowledge of local area network (LAN) operations and familiarity with communication protocols that are used to
Inhaltszusammenfassung zur Seite Nr. 6
6 ABOUT THIS GUIDE Table 2 Text Conventions Convention Description Words in italics Italics are used to: Emphasize a point. Denote a new term at the place where it is defined in the text. Identify menu names, menu commands, and software button names. Examples: From the Help menu, select Contents. Click OK. Words in bold Boldface type is used to highlight command names. For example, “Use the display user-interface command to...” Related The following manuals offer addit
Inhaltszusammenfassung zur Seite Nr. 7
PRODUCT OVERVIEW 1 Preface The 3Com Switch 8800 Family of Routing Switches (referred to as the Switch 8800 Family) are intelligent, multi-layer modular LAN switches and are ideal for enterprise environments where non-stop availability of critical applications and the highest performance, security, and granular control are required. The Switch 8800 Family delivers high density Gigabit and 10 Gigabit switching in an integrated chassis platform. Built-in support for IPv6, MPLS, Power over Ethe
Inhaltszusammenfassung zur Seite Nr. 8
8 CHAPTER 1: PRODUCT OVERVIEW Currently, the Switch 8800 Family include the following models: ■ Switch 8807: This model provides up to 600 Gbps switching capacity. It supports (for example) up to 240 GE ports and 20 x 10GE ports. Figure 1 3Com Switch 8807 (7-Slot Chassis) ■ Switch 8810: This model provides up to 960 Gbps switching capacity. It supports (for example) up to 192 GE ports and 32 x 10GE ports. Figure 2 3Com Switch 8810 (10-Slot Chassis)
Inhaltszusammenfassung zur Seite Nr. 9
Preface 9 ■ Switch 8814: This model provides up to 1.44 Tbps switching capacity. It supports (for example) up to 576 GE ports and 48 x 10GE ports. Figure 3 3Com Switch 8814 (14-Slot Chassis)
Inhaltszusammenfassung zur Seite Nr. 10
Fan tray 10 CHAPTER 1: PRODUCT OVERVIEW General Architecture The Switch 8800 Family use integrated chassis, which can be subdivided into power area, board area, backplane and fan area. Chassis and Slots Switch 8807 Figure 4 Switch 8807 slots Fabric Fabric I/O Module I/O Module I/O Module I/O Module I/O Module PoE AC PSU AC PSU Entry ■ The Switch 8807 chassis provides seven slots in its board area: The top two accommodate fabrics, which can operate in 1+1 redundancy mode; the remaining five
Inhaltszusammenfassung zur Seite Nr. 11
Fan tray General Architecture 11 Switch 8810 Figure 5 Switch 8810 slots I/O Module I/O Module I/O Module I/O Module Fabric Fabric I/O Module I/O Module I/O Module I/O Module PoE AC PSU AC PSU Entry ■ The Switch 8810 chassis provides ten slots in its board area: The middle two accommodate fabric modules, which can operate in 1+1 redundancy mode; the remaining eight accommodate I/O or application modules, which you can select from various available models. All modules in this area are hot-sw
Inhaltszusammenfassung zur Seite Nr. 12
Fan tray 1 Fan tray 2 12 CHAPTER 1: PRODUCT OVERVIEW Switch 8814 Figure 6 Switch 8814 slots I/O Module I/O Module I/O Module I/O Module I/O Module I/O Module Fabric Fabric I/O Module I/O Module I/O Module I/O Module I/O Module I/O Module PoE AC PSU AC PSU entry ■ The Switch 8814 chassis provides 14 slots in its board area: The middle two accommodate fabric modules, which can operate in 1+1 redundancy mode; the remaining 12 accommodate I/O or application modules, which you can select from va
Inhaltszusammenfassung zur Seite Nr. 13
General Architecture 13 The Switch 8807 uses a passive backplane, which provides five I/O module interfaces, two fabric interfaces, one fan interface, and three -48V power interfaces (two for PSUs and one for PoE entry module). ■ Switch 8810 The Switch 8810 uses a passive backplane, which provides eight I/O module interfaces, two fabric interfaces, one fan interface, and three -48V power interfaces (two for PSUs and one for PoE entry module). ■ Switch 8814 The Switch 8814 uses a passive back
Inhaltszusammenfassung zur Seite Nr. 14
14 CHAPTER 1: PRODUCT OVERVIEW ■ A Switch 8800 supports up to 4500 W (220 V)/2250 W (110 V) power to its PDs. It determines whether to deliver power to a newly detected PD depending on the power it currently supplied. PoE entry area The PoE-supported Switch 8807/Switch 8810/Switch 8814 chassis has a PoE entry area between the two power supply units. You can insert a PoE 3C17510 Switch 8800 PoE Entry Module into this area, and connect this module to a 3C17509 Switch 8800 External PoE Power R
Inhaltszusammenfassung zur Seite Nr. 15
General Architecture 15 Table 2 describes typical equipment configurations and specifications of external PoE power system. Table 2 Typical equipment configurations and specifications of external PoE power system Item Description Physical dimensions (H x W x D) 177 x 486 x 320.5 mm (7.0 x 19.1 x 12.6 in.) System controller One Rectifier Two NP2500UAC (required) + one redundant NP2500UAC (optional) AC accessory Three AC inputs and switches Three-phase AC voltage detection circuit Input vo
Inhaltszusammenfassung zur Seite Nr. 16
16 CHAPTER 1: PRODUCT OVERVIEW Role and function The MBUS system is powered by 5 V from the MBUS on the fabric. The 5 V power on the two fabrics are redundant to each other. Each MBUS module is attached to the MBUS, which contains two control lines: MBUS0 and MBUS1. Each card has an independent MBUS module, those on the fabrics are primary MBUS modules, and those on application modules are secondary MBUS modules. When the fabrics operate in redundancy mode, the MBUS module on the active fabr
Inhaltszusammenfassung zur Seite Nr. 17
Fabric Modules 17 Table 4 LEDs on fan tray panel LED Color Status Status RUN Green OFF The fan tray is faulty. ON The fan tray is operating normally. ALM Red OFF The fan tray is operating normally. ON The fan tray is faulty. Fabric Modules The Switch Fabric serves as the core of the Switch 8800 Family.The following fabric models are available to the Switch 8800 Family: ■ 3C17508 - 3Com Switch 8800 360 Gbps Fabric ■ 3C17539 - 3Com Switch 8800 720 Gbps Fabric These fabric modules provide: ■
Inhaltszusammenfassung zur Seite Nr. 18
18 CHAPTER 1: PRODUCT OVERVIEW Figure 10 360 Gbps Switch Fabric panel Compact Flash (CF slot) The 360 Gbps Switch Fabric module provides a CF slot to accommodate a standard CF card, where you can save logging information, host version information, alarming and other diagnostic information and conveniently upgrade software online. The fabric ships with a CF memory card. Management Ports The Management 10Base-T/100Base-TX port uses an RJ-45 connector. It can connect a background terminal fo
Inhaltszusammenfassung zur Seite Nr. 19
Fabric Modules 19 Table 8 RS232/485 port specifications Item Description Service The port for monitoring and communication with the external subsystem, such as external PoE power supply module ■ Console port The Console port uses an RJ-45 connector. It can be connected to a background terminal for system debugging, maintenance, management, and host software loading. Table 9 Console port specifications Item Description Connector RJ-45 Standard Asynchronous EIA/TIA-232 Baud rate 9600 bp
Inhaltszusammenfassung zur Seite Nr. 20
20 CHAPTER 1: PRODUCT OVERVIEW Table 11 CF status LED LED Status CFS ON The CF card is in position and is idle. You cannot remove the card. Blinking The CF card is in position and reading/writing data. You cannot remove the card. OFF The CF card is out of position or offline (you can force the in-position CF card to go offline using the appropriate background command). You can remove/insert the card. ■ Status LEDs for I/O module The 360 Gbps Switch Fabric module has 12 pairs of LEDs to i
