Inhaltszusammenfassung zur Seite Nr. 1
RX-5502(A) 2007.5.17 9:15 AM 페이지 1
Inhaltszusammenfassung zur Seite Nr. 2
RX-5502(A) 2007.5.17 9:15 AM 페이지 1
Inhaltszusammenfassung zur Seite Nr. 3
RX-5502(A) 2007.5.17 9:15 AM 페이지 2 SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should connection to grounding electrodes, and requirements for the be read before the product is operated. grounding electrode. See Figure 1. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions - Al
Inhaltszusammenfassung zur Seite Nr. 4
RX-5502(A) 2007.5.17 9:15 AM 페이지 3 Introduction READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO This symbol is intended to alert the user to the presence CAUTION NOT REMOVE COVER (OR BACK). NO USER- of important operating and maintenance (servicing) SER
Inhaltszusammenfassung zur Seite Nr. 5
RX-5502(A) 2007.5.17 9:15 AM 페이지 4 CONTENTS SAFETY INSTRUCTIONS ....................................................................................................................................2 Introduction �READ THIS BEFORE OPERATING YOUR UNIT......................................................................................... 3 System Connections ........................................................................................................................................ 5
Inhaltszusammenfassung zur Seite Nr. 6
RX-5502(A) 2007.5.17 9:15 AM 페이지 5 System Connections • Do not plug the AC input cord into the wall AC outlet until all connections are completed. • Be sure to connect the white RCA pin cords to the L (left) and the red RCA pin cords to the R (right) jacks when making audio connections. • Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver. 1. CONNECTING ANTENNAs • Change the position of the FM indoor anten- na until you get the best rece
Inhaltszusammenfassung zur Seite Nr. 7
RX-5502(A) 2007.5.17 9:15 AM 페이지 6 2. CONNECTING PHONO �Note •Do not connect the turntable with MC type cartridge directly. If so, use a separate head amplifier or step-up transformer. 3. CONNECTING AUDIO COMPONENTS • The AUX jacks may also be connected to an additional component. • The DVD jacks may be connected to AUDIO OUT jacks of video components such as DVD player, TV, etc. • The TAPE IN/OUT jacks can be connected to audio recording equipment such as a tape deck, an MD recorder, etc.
Inhaltszusammenfassung zur Seite Nr. 8
RX-5502(A) 2007.5.17 9:15 AM 페이지 7 4. CONNECTING SPEAKERS • You can connect up to four pairs of speakers to this receiver and select the various combinations of speakers according to your tastes. • The speakers C and D can be installed in the main room as the speakers A and B can or in the another room (ROOM2) for ROOM2 playback. (For details, refer to "ROOM2 PLAYBACK" on page 19.) • Be sure to connect speakers firmly and correctly according to the channel (left and right) and the polarity (+
Inhaltszusammenfassung zur Seite Nr. 9
RX-5502(A) 2007.5.17 9:15 AM 페이지 8 Front Panel & Remote Controls �FRONT PANEL �FLUORESCENT DISPLAY �REMOTE CONTROLS 8
Inhaltszusammenfassung zur Seite Nr. 10
RX-5502(A) 2007.5.17 9:15 AM 페이지 9 1. POWER SWITCH 13. BALANCE BUTTON Push this switch to enter the standby mode. When adjusting the sound volume balance, press To switch the power off, push again this switch. this button to enter the balance mode. 2. POWER ON BUTTON 14. BALANCE, TREBLE/BASS UP/DOWN (▲ ▲/▼ ▼) In the standby mode, when this button is pressed, BUTTONS the unit is turned on to enter the operating mode. At the balance mode, adjust the sound volume balance between left and right
Inhaltszusammenfassung zur Seite Nr. 11
RX-5502(A) 2007.5.17 9:15 AM 페이지 10 REMOTE CONTROL OPERATION RANGE �Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. LOADING BATTERIES 1. Remove the cover. 2. Load two batteries matching the polarity. �Remove the batteries when they are not used for a long time. �Do not use the rechargeable batteries(Ni-Cd type). 10
Inhaltszusammenfassung zur Seite Nr. 12
RX-5502(A) 2007.5.17 9:15 AM 페이지 11 Operations LISTENING TO A PROGRAM SOURCE Before operation ∙Push the POWER switch. • This unit enters the standby mode and the STANDBY indicator lights up. This means that the receiver is not disconnected from the AC mains and a small amount of current is retained to support the operation readiness. • To switch the power off, push the POWER switch again. Then the power is cut off and the STANDBY indicator turns off. 1. In the standby mode, turn the power o
Inhaltszusammenfassung zur Seite Nr. 13
RX-5502(A) 2007.5.17 9:15 AM 페이지 12 3. Select the desired input source. �Each time the "INPUT SELECT ◀/▶" buttons are pressed, the input source is changed as follows : →TUNER ↔ CD ↔ AUX ↔ DVD ↔ TAPE ↔ PHONO ← (Frequency display) 4. Operate the selected component for playback. 5. Adjust the volume to a comfortable listening level. 6. To mute the sound. • "MUTE" flickers. • To resume the previous sound level, press this button again. • When adjusting the volume, the mutting effect is turne
Inhaltszusammenfassung zur Seite Nr. 14
RX-5502(A) 2007.5.17 9:15 AM 페이지 13 7. To listen with the headphones. • Be sure to switch off all the speakers installed in the main room. Adjusting the tone (bass and treble) 8. Enter the tone mode. • Each time this button is pressed, the corresponding tone mode is selected and shown for 5 seconds as follows: � BASS � TRBL �Note: • When the tone direct function is activated, the tone mode cannot be entered and “TON DIR” flickers for 3 seconds. 9. At the desired tone mode, adjust the tone a
Inhaltszusammenfassung zur Seite Nr. 15
RX-5502(A) 2007.5.17 9:15 AM 페이지 14 Adjusting the sound volume balance 11. Enter the balance mode. • "BAL" and the balance level are displayed for 5 seconds. 12. Adjust the sound volume balance between the left and right speakers. • If the balance display disappears, start from the step 11 again. • The balance level can be adjusted within the range of L10 ~ R 10. �Note: • In general, the balance level is adjusted to 0. 14
Inhaltszusammenfassung zur Seite Nr. 16
RX-5502(A) 2007.5.17 9:15 AM 페이지 15 LISTENING TO RADIO BROADCASTS Auto tuning 1. Select the tuner and then the desired band. • Each time this button is pressed, the tuner is automatically selected and the band is changed as follows : → FM ST → FM MONO → AM • When the FM stereo broadcast is tuned, the FM mode changes as follows: � Stereo mode : "ST" lights up. Mono mode : "ST" turns off. � • When FM stereo broadcasts are poor because of weak broadcast signals, select the FM mono mode ("S
Inhaltszusammenfassung zur Seite Nr. 17
RX-5502(A) 2007.5.17 9:15 AM 페이지 16 Manual tuning • Manual tuning is useful when you already know the frequency of the desired station. • Perform the steps 1 and 2 in "Auto tuning" procedure on page 15 and press the TUNING/PRESET UP (▲ /+) or DOWN (▼/-) button repeatedly until the right frequency has been reached. Auto presetting • Auto presetting function automatically searches for FM stations only and store them in the memory. • While listening to radio broadcasts, press and hold down the
Inhaltszusammenfassung zur Seite Nr. 18
RX-5502(A) 2007.5.17 9:15 AM 페이지 17 3. Press the TUNING/PRESET UP (▲/+) or DOWN (▼/-) button to select the desired preset number and press the MEMORY button. • The station has now been stored in the memory. • A stored frequency is erased from the memory by storing another frequency in its place. • If "MEM" turns off, start again from the above step 2. 4. Repeat the above steps 1 to 3 to memorize other stations. �MEMORY BACKUP FUNCTION The following items, set before the receiver is turned of
Inhaltszusammenfassung zur Seite Nr. 19
RX-5502(A) 2007.5.17 9:15 AM 페이지 18 RECORDING • The volume, tone(bass, treble) and balance settings have no effect on the recording signals. • When you select tuner, CD, DVD, AUX or PHONO as a recording source, recording can be made on the TAPE. • The ROOM2 input source cannot be recorded onto the TAPE. Recording with TAPE 1. Select the desired input as a recording source except for TAPE. 2. Start recording on the TAPE. 3. Start play on the desired input. OTHER FUNCTIONS Operating the sleep t
Inhaltszusammenfassung zur Seite Nr. 20
RX-5502(A) 2007.5.17 9:15 AM 페이지 19 ROOM2 PLAYBACK • This function allows enjoying one source in the main room and playing another in a different room at the same time. • Even when this receiver enters the standby mode, in such a case that "R2" is dimly lit, meaning only the ROOM2 circuitry operates, the ROOM2 source can be played independently. Therefore, when you do not use the ROOM2 function, turn off the ROOM2 function to save electricity. • To enjoy ROOM2 source, turn on the ROOM2 functi
