Inhaltszusammenfassung zur Seite Nr. 1
Contents
AV Receiver
Before using 2
DTR-8.3
Facilities and connections 10
Instruction Manual
Setup and operation 31
Thank you for purchasing the AV Receiver.
Please read this manual thoroughly before making
Remote controller 64
connections and plugging in the unit. Following the
instructions in this manual will enable you to obtain
optimum performance and listening enjoyment
from your new AV Receiver. Please retain this
manual for future reference.
Appendix 82
Inhaltszusammenfassung zur Seite Nr. 2
WARNING: WARNING AVIS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, RISK OF ELECTRIC SHOCK RISQUE DE CHOC ELECTRIQUE DO NOT OPEN NE PAS OUVRIR DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated CAUTION: “dangerous voltage” within the product’s enclosure that may be of TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT sufficient magnitude to constitute a risk of
Inhaltszusammenfassung zur Seite Nr. 3
21. Replacement Parts – When replacement parts are required, be FIGURE 1: sure the service technician has used replacement parts specified EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL by the manufacturer or have the same characteristics as the ELECTRICAL CODE, ANSI/NFPA 70 original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. ANTENNA 22. Safety Check – Upon completion of any service or repairs to the LEAD IN WIRE appliance, ask the service technician to
Inhaltszusammenfassung zur Seite Nr. 4
Contents RS 232 port ..................................................................... 28 Before using Connecting to devices with analog multi channel output .......29 Important Safeguards......................................... 2 Connecting auxiliary power amplifier ........................... 29 Precautions ......................................................... 3 Connecting to an external device with 12V TRIGGER terminal .................................................................
Inhaltszusammenfassung zur Seite Nr. 5
Contents 2-2. Multichannel Setup Sub-menu (When NET AUDIO is Organizing macros and timers into groups .................... 76 not selected as the input source) ............................. 50 Using the remote controller with Radio Frequency 2-3. Video Setup Sub-menu ........................................... 51 (USA & Canadian models only) .................. 77 2-4. Character Input Sub-menu ...................................... 51 Changing the remote controller’s RF IR Settings ......... 77 2
Inhaltszusammenfassung zur Seite Nr. 6
Features Amplifier Features Other Performance Features 110 Watts minimum of continuous RMS power to IntelliVolume each of the seven channels into 8 W from 20 Hz to Character Input 20 kHz with no more than 0.08 % THD (FTC Backlit/preprogrammed & learning remote with rated) LED display 7.1 Channel Amplifier VLSC (Vector Linear Shaping Circuitry) for L/ Wide Range Amplifier Technology (WRAT) C/R channels (Other than USA, Canadian and Linear Optimum Gain Volume Circuitry Australian m
Inhaltszusammenfassung zur Seite Nr. 7
Supplied accessories Check that the following accessories are supplied with the DTR-8.3. Remote controller × 1 Batteries (AA, R6 or UM-3) × 4 AM loop antenna × 1 FM indoor antenna × 1 RS232 cable for PC connection × 1 Australian model only 1 2 3 Speaker Cable Speaker cable label × 1 Power cord × 1 (See page 23.) 75/300 Ω antenna adapter × 1 Before using this unit Connecting the power cord Using the remote controller Plug the supplied power cord into this AC INLET. Point the remote controller to
Inhaltszusammenfassung zur Seite Nr. 8
Setting up the remote controller Insert batteries Characterizing the remote controller 1. Slide the battery cover off the back of the remote Sending eye/Learning eye controller. Direct-access buttons Contrast dial Touchscreen Left/Right Backlight button buttons The intelligent remote controller can be used for all devices that understand infrared remote controller signals. Its easy-to-use 2. Insert 4 AA batteries (included in package) as touchscreen and its intuitive interface makes it a perfect
Inhaltszusammenfassung zur Seite Nr. 9
Setting up the remote controller Touch the screen to start 6. Left and Right buttons The Left and Right buttons change function depending on the device To turn on the screen, tap it gently with your finger. the remote controller is operating. The current function is displayed To use the touchscreen, simply tap the images you see on the screen. on the touchscreen right above the button. The function can be either There’s no need to turn the screen off — it shuts off automatically to an IR (infrar
Inhaltszusammenfassung zur Seite Nr. 10
Index parts and facilities Here is an explanation of the controls and displays on the front panel of the DTR-8.3. Front panels Front door Push here to open the front door. L 10
Inhaltszusammenfassung zur Seite Nr. 11
Index parts and facilities For further operational instructions, see the pages indicated in Rec Out/Zone 2/Off buttons [38-40] brackets [ ]. These buttons allow you to use the DTR-8.3 to output to a remote zone (Zone 2) or to another component for recording (Rec Out). Front panels Press the Rec Out button to output the audio and video signals to a recording component for recording. Press the Zone 2 button to enjoy the output from the DTR-8.3 in a different room, which is referred to Standby/On
Inhaltszusammenfassung zur Seite Nr. 12
Index parts and facilities Tuning / , Preset / buttons [36, 37, 43] Enter button [43] To tune into a radio station, press the Tuning / buttons. The tuner Press to display the screen for the item that is selected in the Setup frequency is displayed in the front display and it can be changed in 50- Menu. kHz increments for FM and 10-kHz (or 9-kHz) increments for AM. When FM is selected as the input source, you can hold down either Return button [43] the Tuning or button and then release it to ac
Inhaltszusammenfassung zur Seite Nr. 13
Index parts and facilities Rear panels DIGITAL PRE OUT COMPONENT AUDIO VIDEO S VIDEO INPUT R L ANTENNA VIDEO FRONT SPEAKERS SURR SPEAKERS COAX FRONT OUTPUT AV RECEIVER MONITOR R R L OUT 1 Y MODEL NO. DTR-8.3 RATING: AC 120 V 60 Hz 8.4 A R L SUB CENTER AM 2 OUT ZONE 2 PB AC OUTLETS SURR 3 IN DVD PR SURR R L BACK/ OPT INPUT 1 ZONE 2 FM 1 Y OUT 75 ETHERNET [NET-TUNE] VIDEO 1 SURR FRONT MULTI CH 2 IN PB CENTER BACK/ INPUT SPEAKER ZONE 2 AUDIO R L AC 120 V 60 Hz CAUTION: SPEAKERS R L SWITCHED
Inhaltszusammenfassung zur Seite Nr. 14
Index parts and facilities AV Amp (Select AV Amp on the Home menu) Remote controller (page 1/4) Home menu – CONT + MUTE LIGHT + CH – VOL (page 2/4) (page 3/4) (page 4/4) 14
Inhaltszusammenfassung zur Seite Nr. 15
Index parts and facilities For details on how to use the remote controller, refer to “Using Second operation menu (page 2/4) the remote controller” (page 64). Select AV Amp in the Home menu to display the operation buttons. Listening mode buttons [35] You can select a listening mode. CONT +/– buttons If the display stays blank or becomes black, adjust the contrast dial Display button [33] on the left side. For changing the display in the front display. LIGHT button Re-EQ button [57, 60] Press to
Inhaltszusammenfassung zur Seite Nr. 16
Connecting to Audio/Video equipment • Be sure to always refer to the instructions that came with the Cables are depicted in the connection diagrams as shown below. component that you are connecting. • Do not plug in the power cord until all connections have been Left (white) L properly made. Audio connection cable • For input jacks, red connectors (marked R) are used for the right channel, white connectors (marked L) are used for the left channel, and yellow connectors (marked V) are used for Ri
Inhaltszusammenfassung zur Seite Nr. 17
Connecting to Audio/Video equipment Here is an explanation of typical ways to connect various components to the DTR-8.3. There are many ways that any one component can be connected, and it is up to you to decide which method best fits your situation. The directions given here are only one option and should only be thought of as such. It is best to fully understand the nature of each connector and terminal as well as those of your components and their features to ascertain which method of connect
Inhaltszusammenfassung zur Seite Nr. 18
Connecting to Audio/Video equipment Connecting a DVD Player with 5.1-Channel Output : Signal flow Digital audio output (coaxial) R (red) Analog audio output DIGITAL PR COMPONENT L (white) AUDIO VIDEO S VIDEO INPUT TENNA R VIDEO COAX FRONT OUTPUT MONITOR 1 OUT Y Video output R L SUB AM 2 OUT ZONE 2 PB SURR S Video output 3 IN DVD PR SURR R BACK/ OPT INPUT 1 ZONE 2 FM 1 OUT Y 75 VIDEO 1 FRONT 2 IN PB 4. DVD player (DVD) UDIO R L SUB 3 PHONO OUT PR VIDEO 2 INPUT 2 SURR 4 CD IN Y R OUT OPT 1 IN V
Inhaltszusammenfassung zur Seite Nr. 19
Connecting to Audio/Video equipment : Signal flow Video input 5. TV monitor or projector S Video input (MONITOR OUT) DIGITAL PRE COMPONENT AUDIO VIDEO S VIDEO INPUT NNA R VIDEO COAX FRONT OUTPUT MONITOR OUT 1 Y Y R L SUB 2 AM PB OUT ZONE 2 PB Component video input SURR S Video input 3 IN DVD PR PR SURR R BACK/ OPT INPUT 1 ZONE 2 FM 1 Y Video input OUT 75 VIDEO 1 FRONT 2 IN PB O R L (white) L Analog audio SUB 3 PHONO OUT PR input VIDEO 2 SURR INPUT 2 4 CD IN Y R (red) R OUT OPT 1 IN VIDEO 3 P
Inhaltszusammenfassung zur Seite Nr. 20
Connecting to Audio/Video equipment Digital audio input (optical) : Signal flow Digital audio output (coaxial) S Video input Video input DIGITAL PRE COMPONENT R (red) AUDIO VIDEO S VIDEO Analog audio INPUT TENNA R VIDEO COAX FRONT OUTPUT MONITOR input 1 OUT Y R L SUB AM 2 OUT ZONE 2 PB L (white) SURR 3 IN DVD PR SURR 7. DVD recorder, other digital video R BACK/ OPT INPUT 1 ZONE 2 recording device (VIDEO 2) FM 1 OUT Y 75 VIDEO 1 FRONT 2 IN PB UDIO R L SUB 3 PHONO OUT PR VIDEO 2 INPUT 2 SURR 4
