Inhaltszusammenfassung zur Seite Nr. 1
User’s Manual
FOX HD-SDI
Multi-Rate SDI Fiber Optic Transceiver
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan
1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Rd. #04-01 Kyodo Building, 16 Ichibancho 68-1384-01 Rev. A
Anaheim, CA 92805 3821 AH Amersfoort, The Netherlands PM Industrial Bldg., Singapore 368363 Chiyoda-ku, Tokyo 102-0082
11 07
800.633.9876 714.491.1500 +800.3987.6673 +31.33.453.4040 +800.7339.8766 +65.6383.4400 J
Inhaltszusammenfassung zur Seite Nr. 2
Precautions Safety Instructions � English Extron’s Warranty Warning Power sources � This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety Extron Electronics warrants this product against defects in materials and wor
Inhaltszusammenfassung zur Seite Nr. 3
警告 安全须知 • 中文 电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备 这个符号提示用户该设备用户手册中 必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线 有重要的操作和维护说明。 ( 地 线 ) 是 安 全 设 施 , 不 能 不 用 或 跳 过 。 拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线,或任何接到市电系统的电源线。 电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。 露的危险电压,有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部没 注意 有用户可以更换的零件。为避免出现触电危险不要自己 阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理 试图打开设备盖子维修该设备。 解 所 有 安 全 和 使 用 说 明 。 通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危
Inhaltszusammenfassung zur Seite Nr. 4
Quick Start Guide — FOX HD-SDI The FOX HD-SDI is a transceiver that can function as a N transmitter and/or a receiver. At least two units are required for a transmitter-receiver system with at least one fiber optic cable linking each two units. The FOX HD-SDI is available in single mode or multimode versions. Connect and operate two or more FOX HD-SDI units as follows: Step 1 Power off all equipment. If desired, mount the units in racks. Step
Inhaltszusammenfassung zur Seite Nr. 5
Quick Start Guide — FOX HD-SDI, cont’d Table of Contents Chapter One • Introduction..................................................... 1-1 Step 6 About this Manual ..................................................................... 1-2 Chapter One • Introduction..................................................... 1-1 Receiving unit — Connect one or two monitors to the unit's Buffered Outputs BNC connectors. About the FOX HD-SDI..............................................................
Inhaltszusammenfassung zur Seite Nr. 6
Table of Contents, cont'd FOX HD-SDI Chapter One 1 Introduction About.this.Manual About.the.FOX.HD-SDI Features ii FOX HD-SDI • Table of Contents
Inhaltszusammenfassung zur Seite Nr. 7
Introduction The FOX HD-SDI units output continuous, W About the FOX HD-SDI invisible light, which may be harmful and The Extron FOX HD-SDI product family consists of two models dangerous to the eyes; use with caution. (MM and SM) of high performance digital (HD-SDI, SDI, or 3G-SDI) video fiber optic transceivers. The transmitted signal Do not look into the rear panel fiber optic • can include any audio or unidirectional serial data that is cable connectors
Inhaltszusammenfassung zur Seite Nr. 8
Introduction, cont’d A bidirectional transceiver can also simultaneously receive Features a proprietary signal from another transceiver (in any Extends HD-SDI, SDI, and 3G-SDI signals very long distances configuration) on its Optical Rx port, convert the proprietary over a single fiber — The FOX HD-SDI supports multi- signal to back to the original format digital video, and output rate SDI at rates up to 2.97 Gbps, and complies with the video on its own two Buffered Outputs BNC connectors
Inhaltszusammenfassung zur Seite Nr. 9
Introduction, cont’d FOX HD-SDI Chapter Two 2 Installation and Operation Mounting.the.Unit Connections.and.Settings Operation 1-6 FOX HD-SDI • Introduction
Inhaltszusammenfassung zur Seite Nr. 10
Installation and Operation Mounting instructions Mounting the Unit For optional rack mounting, mount the transceiver on any of the Installation and service must be performed by C following rack shelves: authorized personnel only. ® • RSF 123 3.5" deep 1U VersaTools rack shelf kit The 1" high, quarter-rack width transceiver can be placed on (part #60-190-20) (figure 2-1) a tabletop, mounted on a rack shelf, mounted under a desk or • RSB 123 3.5" deep 1U VersaTools rack shelf
Inhaltszusammenfassung zur Seite Nr. 11
Installation and Operation, cont’d 1U Universal Rack Shelf 1/2 Rack Width Front False Faceplate 1/4 Rack Width Front False Faceplate Both front false faceplates use 2 screws. (2) 4-40 x 3/16" Screws Use 2 mounting holes on Figure 2-3 — Under-desk mounting opposite corners. 6. Align the installed screws with the slots in the mounting Figure 2-2 — Mounting the transceiver on a standard brackets, and place the transceiver against the surface, rack shelf with the screws through the bracke
Inhaltszusammenfassung zur Seite Nr. 12
Installation and Operation, cont’d c. Tighten the screws. Through-desk mounting d. Replace the unit inside the surface (step 4). The transceiver can be mounted through a desk or other furniture using an optional Extron MBD 129 through-desk mounting kit, part #70-077-02. Mount the transceiver through a Projector mounting desk or table as follows (figure 2-4): The transceiver can be mounted on a projector bracket using either of the following optional Extron projector mounting kits: • PMK 30
Inhaltszusammenfassung zur Seite Nr. 13
Installation and Operation, cont’d 3. Use the two included tie wraps to strap the power supply PMK 350 mounting to one of the brackets. Mount the transceiver to a PMK 350 bracket as follows: The PMK 300 has a hole in the bottom plate that allows the N 1. Remove the front and back plates from the PMK 350 projector pole to be inserted through the center of the plate (figure 2-7), using an Extron Tweeker or a #2 Philips (figure 2-6), rather than outside of the
Inhaltszusammenfassung zur Seite Nr. 14
Installation and Operation, cont’d 6. Assemble the U-bolt and the following parts in the Connections and Settings following order (figure 2-8): All connectors are on the rear panel (figure 2-9). Mount Plate Flange FOX HDSDI POWER OPTICAL Contoured 12V MODE 0.3A MAX Base U-bolt 1 2 1 2 HD/SDI IN BUFFERED OUTPUTS Tx Rx L-shaped Bracket 5 1 2 3 4 Slotted Hole in PMK Tray L-shaped Bracket Screws Figure 2-9 — FOX HD-SDI transceiver’s connectors Ceiling HD-SDI Input connector — If the FOX
Inhaltszusammenfassung zur Seite Nr. 15
Installation and Operation, cont’d Rx — If the FOX HD-SDI is configured as a bidirectional Power supply wiring transceiver or as a receiver, for one-way communications Figure 2-10 shows how to wire the power connector. from the transmitting unit, connect a fiber optic cable to the Optical Rx connector. If the FOX HD-SDI is configured as a bidirectional transceiver, Smooth Ridges connect the free end of this fiber optic cable to the Optical Tx connector on the transmitting FOX HD-SDI. S
Inhaltszusammenfassung zur Seite Nr. 16
Installation and Operation, cont’d System operation Operation After the transmitting and receiving units and all of their Front panel indicators connected devices are powered up, the system is fully All indicators are on the front panel (figure 2-13). operational. If any problems are encountered, ensure all traditional and fiber cables are routed and connected properly. RATE 270 1.485 2.97 Mbps Gbps Gbps UNKNOWN FOX HDSDI 1 2 Figure 2-13 — FOX HD-SDI's transceiver’s indicators Power indica
Inhaltszusammenfassung zur Seite Nr. 17
Installation and Operation, cont’d FOX HD-SDI Appendix A A Reference Information Specifications Part.Numbers 2-16 FOX HD-SDI • Installation and Operation
Inhaltszusammenfassung zur Seite Nr. 18
Reference Information Video Specifications Signal type ...................................... HD-SDI, SDI, and 3G-SDI digital video The FOX HD-SDI is a transceiver that can function as a N signals transmitter and/or as a receiver. Two units are required for a Gain ................................................ Unity transmitter-receiver system with one fiber optic cable linking Resolution....................................... 8 or 10 bits, automatic the
Inhaltszusammenfassung zur Seite Nr. 19
Reference Information, cont’d Return loss ..................................... <-25 dB @ 100 MHz Part Numbers DC offset ........................................ ±5 mV with input at 0 offset FOX HD-SDI part numbers General The FOX HD-SDI is a transceiver that can function as N External power supply ................ 100 VAC to 240 VAC, 50/60 Hz, 6 watts, a transmitter and/or as a receiver. At least two units are external; to 12 VDC, 2 A, regulated required for a t
Inhaltszusammenfassung zur Seite Nr. 20
Reference Information, cont’d Optional accessories Accessories Part number RSU 129 9.5" 1U universal rack shelf kit 60-190-01 RSB 129 9.5" 1U basic rack shelf 60-604-01 RSU 126 6" deep 1U universal rack shelf kit 60-190-10 RSU 126 6" deep 1U universal rack shelf 60-604-10 ® RSF 123 3.5" deep 1U VersaTools 60-190-20 rack shelf kit RSB 123 3.5" deep 1U VersaTools 60-604-20 rack shelf MBD 129 through desk mounting kit 70-077-02 PMK 300 projector mounting kit 70-374-01 PMK 350 low profile pro