Inhaltszusammenfassung zur Seite Nr. 1
AMPLIFIER MODELS
D500/1 D1000/1 D2000/1 D3000/1
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 What’s Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 3
CONGRATULATIONS TM Thank you for choosing Precision Power audio equipment. Designed and engineered in the USA, this product combines innovative technology with the finest materials to consistently deliver ™ Absolutely State of the Art performance, sound quality, reliability, TM and value. This Precision Power product reflects our commitment to offer you unparalleled performance and quality for years of dependable service and listening enjoyment. SERVICE TM Do not attempt to service Precision Pow
Inhaltszusammenfassung zur Seite Nr. 4
FEATURES Advanced Instrumentation Input Stage. 24dB/Octave; HP/LP/FULL; 30-4kHz Crossover. Independent Line Output Crossover 30-4kHz PWM Power Supply Triple Darlington Output Stage. AP-IV Protection Circuity TM QBASS Bass Boost High Voltage Input Capability with -12dB Attenuation Switch. Gold Plated RCA Input and Output Connectors. TM PowerLock Speaker and Power Wire Connectors. WHAT’S INCLUDED Amplifier (with speaker and power plugs mounted) (4) Mounting screws and washers 2mm hex wrench 2.5mm
Inhaltszusammenfassung zur Seite Nr. 5
SPECIFICATIONS Nominal Power Ratings MODEL 4ohm MONO 2ohm MONO 1ohm MONO D500/1 1 X 125 1 X 200 1 X 250 D1000/1 1 X 175 1 X 275 1 X 500 D2000/1 1 X 375 1 X 600 1 X 1000 D3000/1 1 X 500 1 X 1000 1 X 1500 General Specifications Conversion Efficiency >80% @4 ohms Frequency Response 20Hz - 200Hz +0, -1dB Total Harmonic Distortion <0.02% Input Sensitivity 200mv - 5 Volts RMS Phase Adjust 0° or 180°, selectable switch RCA Output Jacks HP/LP/Full; 30Hz to 4kHz Input Impedance 40 kohms Supply Voltage 9
Inhaltszusammenfassung zur Seite Nr. 6
Fuse Requirements You will need to install an in-line fuse or circuit breaker in the power wire within 18” of the battery. This fuse or circuit breaker is to protect your vehicle from fire in case the power wire shorts to the vehicle body. If you are only using one amplifier, use the fuse rating indicated in this chart. If you are using more than one amplifier, add up the fuse ratings for all the amplifiers. This sum is the rating for your fuse or circuit breaker. You may also want to add a powe
Inhaltszusammenfassung zur Seite Nr. 7
AMPLIFIER STATUS LEDS 1 2 The LEDs provide the following indications: 1. Power - These LEDs illuminates the center Precision Power logo background when the amplifier power is turned on. 2. Short - These LEDs behind the PPI logo will flash to indicate a short on the output. 2. Thermal - These LEDs behind the PPI logo will extinguish if the amplifier is in thermal shutdown protection. Note: Read the AP-IV Protection Circuit section for additional information regarding Short and Thermal protection.
Inhaltszusammenfassung zur Seite Nr. 8
TOOLS/PARTS FOR INSTALLATION NOTE: TOOLS ARE NOT SUPPLIED. Small flat blade screwdriver Phillips screwdriver (#2 or medium sized) Wire cutters Wire strippers 4 - #6 round head screws, and 1 - #8 sheet metal screw. (or nut, bolt, flat washer, star washer) (see details) 2 - Ring connectors (large enough to accommodate your method of grounding) In-line fuse or circuit breaker Power and ground wire Speaker wire - 12-16 gauge Grommets (sized to work with the power wire you plan to use in your install
Inhaltszusammenfassung zur Seite Nr. 9
Note: The cables running from the battery to the rear of the car should be installed on the side of the car opposite to the antenna. When using 16 gauge wire or larger, run the speaker wires from the amplifier location through the vehicle to the speakers. Observe the same precautions for routing these wires that you followed for running the power and remote turn on wires. Cut off excess and, using wire strippers, strip 1/4-inch of insulation. Locate the speaker/remote turn- TM on PowerLock conne
Inhaltszusammenfassung zur Seite Nr. 10
Note: The amplifier comes with the connector inserted into the amplifier with the wire clamping screws in the up position as shown below. Use a 2mm hex head wrench to secure the wires to the connector. If the connector needs to be unplugged from the amplifier, use a 2.5mm hex head wrench to remove the retaining screw from the connector (set aside and save the retaining screw).The two negative outputs are common to each other as are the two positive outputs. A speaker may be connected to either t
Inhaltszusammenfassung zur Seite Nr. 11
wires as close together as possible, and use the same gauge wire for both. This will ensure that you have a good ground path, and may eliminate such potential problems as engine noise and overheated amplifiers. CHARGING SYSTEM If your total current draw is over 100 amps (or total output power is over 600 watts), you are probably exceeding the capability of your charging system. Dimming lights and fluctuating voltage are solid indicators that you need to upgrade your alternator, battery, or both.
Inhaltszusammenfassung zur Seite Nr. 12
1300W = 108 Amps total current draw 12V If the same amplifier is driven into a 2 ohm load, double it’s 4 ohm RMS rating. These amplifiers will effectively double their power at this load. 1000W X 1.3 X 2 = 2600 watts 2600W = 217 Amps total current draw 12V If you are using more than one amplifier, add up the total current draw for all of them and choose the appropriate gauge based on the grand total. POWER WIRE SIZE A minimum of 8 gauge or a maximum of 4 gauge wire is recommended dependent on th
Inhaltszusammenfassung zur Seite Nr. 13
POWERLOCK CONNECTORS Once you have run both the power and ground wires, then connect the cables to the amplifier. Cut off excess wire, and using wire strippers, strip the ends of the power and ground cables TM approximately 1/4 inch. Locate the PowerLock power and ground connector (supplied). Using a hex wrench, loosen the screws before attempting to insert the cable wires. Insert the wires into the appropriate hole, and tighten the screws. The Power/Ground TM PowerLock will accommodate 4 gauge
Inhaltszusammenfassung zur Seite Nr. 14
FRONT PLATE DIAGRAMS
1. Cooling Plenums: Maintain a minimum 2” clearance around cooling plenums for proper amplifier cooling. TM 2. Speaker/Remote Connector: The PowerLock speaker connector. 3. Output Freq. Control: Use this control to adjust the sub bass ou
Inhaltszusammenfassung zur Seite Nr. 15
12. -12dB Input Attenuation: Push this switch ‘IN’ for high voltage (4V-12V) capability. This button pushed ‘IN’ must be used for speaker level input on common ground head-units or for high voltage line drivers. 13. Phase: These switch sets the phase of the output relative to the amplifier input. 14. RCA Outputs: RCA outputs provide HP/LP/FULL 30-4kHz signal to another amplifier. END PLATE DIAGRAMS
Inhaltszusammenfassung zur Seite Nr. 16
4. Cooling Plenums: Maintain a minimum 2” clearance around cooling plenums for proper amplifier cooling. INPUTS There are two sets of RCA jacks on the front end of your amplifier. The RCA cables from your source unit go in the set labeled INPUTS. If your source unit doesn’t have RCA outputs, then add a set of RCA plugs (available at your dealer) to your front or rear set of speaker leads (see drawing below). Plug them into the input jacks, and push in the -12dB input attenuation switch. SOURCE H
Inhaltszusammenfassung zur Seite Nr. 17
QBASS PLUS SPECIFICATIONS TM QBASS PLUS Up to 18dB of boost with selectable center frequency at 30Hz, 36Hz, 44Hz or 60Hz, with a Q-factor of 2. TM Optional QBASS REMOTE This boost control can be mounted in the dash and will supersede the boost control on the amplifier endplate. 16
Inhaltszusammenfassung zur Seite Nr. 18
QBASS PLUS/QBASS REMOTE On these amplifiers, we’ve taken bass control to a higher level with TM TM QBASS PLUS . The two QBASS switches (labeled 1 and 2) on the front end of the amplifier allow you to select one of four frequency centers 30Hz, 36Hz, 44Hz and 60Hz. On the rear end TM plate you will find the QBASS level control and plug-in for an TM optional QBASS REMOTE dash mounted level control. Adjust the level control clockwise for up to +18dB of boost at your selected frequency. TM QBASS Sett
Inhaltszusammenfassung zur Seite Nr. 19
TC-X CROSSOVER ® Your new amplifier has a TC-X Crossover (Total Control X-over ) 30Hz-4kHz (see this guide for Crossover Chart).12dB per octave phase correlated crossover built-in to provide superior system flexibility without the added expense and installation of an outboard crossover. The speaker outputs of your amplifier are high pass, low pass, or all-pass according to the HP/LP/FULL switch on the front endplate. You would choose low pass (middle position of switch) to use this amplifier for
Inhaltszusammenfassung zur Seite Nr. 20
CROSSOVER DETENT CHART Low Pass High Pass Detent # Frequency (Hz) Frequency (Hz) @ -3dB @ -3dB 1 31 27 2 31 28 3 31 28 4 32 28 5 32 28 6 34 29 7 36 30 8 39 31 9 42 33 10 45 35 11 50 37 12 55 40 13 58 42 14 65 45 15 71 48 16 78 50 17 88 52 18 100 55 19 115 58 20 119 62 21 124 70 22 131 75 23 137 75 24 142 80 25 149 80 26 157 82 27 165 85 28 176 85 29 190 90 30 205 95 31 210 100 32 213 100 33 216 103 34 220 108 35 224 108 36 228 108 37 234 108 38 238 110 39 242 110 40 242 110 41 110 19
