Inhaltszusammenfassung zur Seite Nr. 1
DA304
DA602
DA604
DA904
DA4001
DA6001
DA8001
PERFORMANCE SERIES
INSTALLATION / OWNER'S MANUAL
Mobile Power Amplifiers
Inhaltszusammenfassung zur Seite Nr. 2
INSTALLATION Preparation Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your Dual amplifier is installed by a professional installer or an authorized dealer. Before You Start • Disconnect negative battery terminal. (consult a qualified technician for instructions) • Avoid installing the amplifier where it would be subject to high temperatures, such as from direct sunlight, or where it wo
Inhaltszusammenfassung zur Seite Nr. 3
INSTALLATION Connection Descriptions NOTE: Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used as a general guideline only. Power Wire (+12V) • Disconnect negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • Plan wire routing before cutting any wires to length. Begin by routing the power +12V wire
Inhaltszusammenfassung zur Seite Nr. 4
INSTALLATION Audio Inputs and Controls DA602 1 2 3 4 5 6 7 8 DA304 DA604 1 2 4 5 6 7 8 DA904 High Level Inputs Hi-Pass Filter 1 5 RCA Line Inputs Crossover Mode 2 6 Pass Through Low-Pass Filter 3 7 Gain 8 Bass Boost 4 4
Inhaltszusammenfassung zur Seite Nr. 5
INSTALLATION Power and Speaker Connections DA602 2 3 4 5 1 DA304 3 4 5 1 2 DA604 DA904 1 2 3 4 5 Remote Turn On Speaker Connections 1 4 Fuse(s) Ground Connection 2 5 +12VDC Battery Connection 3 5
Inhaltszusammenfassung zur Seite Nr. 6
INSTALLATION Audio Inputs and Controls DA4001 1 2 3 4 5 6 7 8 9 10 DA6001 DA8001 RCA Line Inputs Bass Boost 1 6 Pass Through Low Pass Filter 2 7 Gain Slave/Master Controls 3 8 Phase Control 9 Data Link 4 Subsonic Filter 10 Remote 5 6
Inhaltszusammenfassung zur Seite Nr. 7
INSTALLATION Power and Speaker Connections DA4001 1 2 3 4 5 DA6001 1 2 3 4 5 DA8001 1 2 3 4 5 Remote Turn On Speaker Connections 1 4 Fuse(s) Ground Connection 2 5 +12VDC Battery Connection 3 7
Inhaltszusammenfassung zur Seite Nr. 8
INSTALLATION Typical Wire Routing MAXIMUM GROUND FUSE No more than 36" (1 meter) 12V BATTERY 12V DC (Power) RCA CABLES SPEAKERS 2-8 ohms REM (Remote Turn On) Main Power Connections Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the +12V lead within 18" of the battery for protection of the vehicle’s electrical system. Fuse Rating Power/Ground Wire Size When replacing fuses, make sure new fuse For optimum performance, use o
Inhaltszusammenfassung zur Seite Nr. 9
INSTALLATION Amplifier Connections 2 Speakers (stereo) Subwoofer (mono) Speaker Connections Connect speaker wires observing polarity. The minimum impedance load for the DA304, DA602, DA604 and DA904 is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage. The DA304, DA602, DA604 and DA904 can 2-8 ohms 1-8 ohms be wired for stereo, bridged or Typical Stereo Wiring stereo/bridged simultaneous Typical Bridged Wiring (2 ohms min
Inhaltszusammenfassung zur Seite Nr. 10
INSTALLATION Master/Slave Mode The Dual mono amplifiers feature a Master/Slave mode, where two amplifiers can be connected together. When two mono amplifiers are connected together, the power from both amplifiers is combined. 10
Inhaltszusammenfassung zur Seite Nr. 11
INSTALLATION Master/Slave Mode (cont.) *MASTER For master amplifier, set the switch to master. This will route the signal through Line-out to the slave amplifier. Set the phase to 0, all adjustments for gain and sound are done on this amplifier. The remote subwoofer control should be connected to master amplifier as well. *SLAVE For slave amplifier, set the switch to slave and phase to 180. Connect the Line-out of master amplifier to input on this amplifier. All adjustments should be set to
Inhaltszusammenfassung zur Seite Nr. 12
INSTALLATION Configuration/Setup Input level Control The input level control (gain) is used to obtain the best possible match between the head unit audio output and the amplifier input. Begin by turning the input level control fully counterclockwise. Next, turn up the head unit volume control around 3/4 of the way up. Adjust the input level control clockwise until audible distortion is heard, then slightly counterclockwise to provide the best match. Repeat for all input level controls.
Inhaltszusammenfassung zur Seite Nr. 13
INSTALLATION Troubleshooting Problem Cause Action +12V wire not connected or incorrect Check connections for proper voltage voltage. REM wire not connected or Unit will not turn on (11~16VDC) incorrect voltage (no power LED indicator) GND wire not connected Check connection to ground Fuse(s) blown Replace fuse(s) Speaker wires not connected Check connections at speakers Volume turned all the way down Increase volume level at head unit One or more spe
Inhaltszusammenfassung zur Seite Nr. 14
INSTALLATION Specifications DA602 Power Output (14.4VDC, 20Hz ~ 20kHz): •60 Watts RMS x 2 channels @ 4ohms •100 Watts RMS x 2 channels @ 2ohms •215 Watts RMS x 1 channel @ 4ohms (bridged) Peak Music Power Output: 380 Watts Signal to noise ratio: 90dB (THD< 0.05% @ 4Ω, 14.4V) Frequency response: 10Hz– 35kHz (-3dB) Amplifier dimensions: 2” x 9.3” x 7.9” (51 x 236 x 201 mm) DA304 Power Output (14.4VDC, 20Hz ~ 20kHz): •40 Watts RMS x 4 channels @ 4ohms •65 Watts RMS x 4 channels @ 2ohms •1
Inhaltszusammenfassung zur Seite Nr. 15
INSTALLATION Specifications DA4001 Power Output (14.4VDC, 20Hz ~ 250Hz): •850 Watts RMS x 1 channel @ 2ohms •1200 Watts RMS x 1 channel @ 1ohm Peak Music Power Output: 3200 Watts Signal to noise ratio: > 80dB (THD < 0.5% @ 4Ω, 14.4V) Frequency response: 20Hz -150Hz (-3dB ) Amplifier dimensions: 2” x 9.3” x11 .8” (51 x 236 x 300 mm) DA6001 Power Output (14.4VDC, 20Hz ~ 250Hz): •1200 Watts RMS x 1 channel @ 2ohms •1 800 Watts RMS x 1 channel @ 1ohm Peak Music Power Output: 4200 Watts Sig
Inhaltszusammenfassung zur Seite Nr. 16
One Year Limited Warranty This warranty gives you specific legal rights. What to do? You may also have other rights which vary 1. Before you call for service, check the from state to state. troubleshooting guide in your owner’s manual. A slight adjustment of any Dual Electronics Corp. warrants this product custom controls may save you a service to the original purchaser to be free from call. defects in material and workmanship for a period
