Bedienungsanleitung Infinity INTERLUDE 108IL10C

Inhaltszusammenfassung zur Seite Nr. 1

™
INTERLUDE SPEAKER SYSTEMS
Owner’s Guide
• IL10
• IL30
• IL40

Inhaltszusammenfassung zur Seite Nr. 2

Infinity Interlude Series The Interlude Series of loudspeakers continues Infinity’s longstanding commitment to accurate sound reproduction. ™ Our proprietary Ceramic Metal Matrix Diaphragm (C.M.M.D.) drivers, precision dividing networks and rigid, well-braced enclosures combine to deliver uncompromised performance in any stereo or multichannel home-theater system. In addition, the IL10, IL30 and IL40 are magnetically shielded for safe placement adjacent to a television. UNPACKING THE SPEAKERS If

Inhaltszusammenfassung zur Seite Nr. 3

INSTALLING FEET IL30 and IL40 Refer to Figure 3 as you perform the following steps: 1. Open each accessory pack and locate the following items: four feet (with spike/round ends), four locking nuts, four nylon domes and one wrench. 2. Lay each speaker on its side and locate the four threaded holes on the bottom. 3. For carpets, screw the round end of a foot into each hole and hand-tighten a nut onto each one. Leave a minimum of 5/8" of exposed spike. (On thicker carpets, you can increase the leng

Inhaltszusammenfassung zur Seite Nr. 4

WIRING THE SYSTEM IMPORTANT: Make sure all equipment is turned off before making any connections. For speaker connections, use a minimum #16-gauge speaker wire with polarity coding.The side of the wire with a ridge or other coding is usually considered positive polarity (i.e., +). NOTE: If desired, consult your local Infinity dealer about speaker wire and connection options. The speakers have coded terminals that accept a variety of wire connectors.The most common connection is shown in Figure 4

Inhaltszusammenfassung zur Seite Nr. 5

BI-WIRING The Interlude Series outer connection panel and internal dividing network are designed so that separate sets of speaker cables can be attached to the low-frequency transducer and midrange/high-frequency transducer portions of this dividing network.This is called bi-wiring. Bi-wiring can provide several sonic advantages and considerably more flexibility in power amplifier selection. + – + 1. Loosen the terminals and remove strapping bars. – 2. Insert the speaker wire for the high fr

Inhaltszusammenfassung zur Seite Nr. 6

FINAL ADJUSTMENTS Check the speakers for playback first by setting the system volume control to a minimum level, and then by applying power to your audio system. Play a favorite music or video segment and increase the system volume control to a comfortable level. NOTE: You should hear balanced audio reproduction across the entire frequency spectrum. If not, check all wiring connections or consult the authorized Infinity dealer from whom you purchased the system for more help. The amount of bass

Inhaltszusammenfassung zur Seite Nr. 7

SPECIFICATIONS IL10 IL30 IL40 Frequency Range: 56Hz – 22,000Hz (±3dB) 48Hz – 22,000Hz (±3dB) 38Hz – 22,000Hz (±3dB) Recommended Amplifier Power Range: 15 – 150 watts 15 – 150 watts 15 – 175 watts Sensitivity: 88dB 88dB 89dB (2.83V @ 1 meter) Nominal Impedance: 8Ω 8Ω 8Ω Crossover Frequency: 2800Hz; 24dB/octave 2800Hz; 24dB/octave 600Hz, 2500Hz; 24dB/octave Low-Frequency Driver: 6-1/2" (165mm) C.M.M.D., 6-1/2" (165mm) C.M.M.D., 8" (203mm) C.M.M.D., magnetically shielded magnetically shielded magne

Inhaltszusammenfassung zur Seite Nr. 8

© 1999 Infinity Systems, Inc. 250 Crossways Park Drive,Woodbury, NY 11797 USA (800) 553-3332 (USA Only) www.infinitysystems.com Infinity is a registered trademark of Infinity Systems, Inc. Printed in USA 12/99 Part No. 335755-001

Inhaltszusammenfassung zur Seite Nr. 9

Inhaltszusammenfassung zur Seite Nr. 10

Inhaltszusammenfassung zur Seite Nr. 11