Inhaltszusammenfassung zur Seite Nr. 1
Crestron C2N-VEQ4
Cresnet 4-Channel Digital Volume Control
Operations Guide
Inhaltszusammenfassung zur Seite Nr. 2
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2005 Crestron Electronics, Inc.
Inhaltszusammenfassung zur Seite Nr. 3
Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control Contents Cresnet 4-Channel Digital Volume Control: C2N-VEQ4 1 Introduction ...............................................................................................................................1 Features and Functions................................................................................................1 Specifications .................................................................................................
Inhaltszusammenfassung zur Seite Nr. 4
Inhaltszusammenfassung zur Seite Nr. 5
Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control Cresnet 4-Channel Digital Volume Control: C2N-VEQ4 Introduction Features and Functions ® ® The Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control module is a digitally controlled 4-channel audio processor that incorporates volume, tone, mixer and equalization capabilities. Each channel has independent settings for volume, treble, bass, mute, and mixer controls plus a 12-band parametric equalizer. Volume/tone controls are
Inhaltszusammenfassung zur Seite Nr. 6
Cresnet 4-Channel Digital Volume Control Crestron C2N-VEQ4 Input and output connections are completely independent of each other. Therefore, it is possible to have a balanced input paired with an unbalanced output and vice-versa. The treble and bass controls are independent from volume and are individually controlled for each channel. Each channel includes a muting relay with 100 dB attenuation. When the signal driving Mute1 goes high, the muting circuit is activated providing 100 dB atte
Inhaltszusammenfassung zur Seite Nr. 7
Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control Specifications The table after this paragraph provides a summary of specifications for the C2N-VEQ4 module. Specifications of the C2N-VEQ4 SPECIFICATION DETAILS Cresnet Power Usage 8.0 Watts (0.3 Amp @ 24 VDC) 12 Default Net ID 1, 2, 3 Control System Update Files 2-Series Control System Version 2.004.CUZ or later CNMSX-AV/PRO Version 5.12.63X.UPZ or later CNRACKX/-DP Version 5.12.63W.UPZ or later ST-CP Version 4.02.
Inhaltszusammenfassung zur Seite Nr. 8
Cresnet 4-Channel Digital Volume Control Crestron C2N-VEQ4 2. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product Catalog for a complete list of 2-Series control systems. 3. Filenames for CNX and ST-CP update files have a UPZ extension. Files on the website may be .zip or self-extracting .exe files containing the .cuz or .upz file. All can be obtained from the Downloads section of the Crestron website. To avoid program problems, make sure you are
Inhaltszusammenfassung zur Seite Nr. 9
Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control C2N-VEQ4 Overall Dimensions 1.50 in (3.81 cm) 6.94 in (17.63 cm) 6.32 in (16.05 cm) 7.07 in (17.96 cm) 1.80 in (4.57 cm) 1.70 in (4.32 cm) C2N-VEQ4 Ports All connections to the C2N-VEQ4 are made through the ports on the rear panel. Refer to the illustrations and descriptions, which follow. C2N-VEQ4 Ports IN and OUT Connectors These four mini connectors provide four channels of balanced/unbalanced audio input (IN 1-4) and four
Inhaltszusammenfassung zur Seite Nr. 10
Cresnet 4-Channel Digital Volume Control Crestron C2N-VEQ4 balanced/unbalanced output (OUT) ports to an amplifier. Each channel includes a muting relay with 100 dB attenuation. G (Chassis Ground) Use this chassis screw to ground the unit to the amplifier and audio source common grounds. NET This 4-pin network connector is used to connect the C2N-VEQ4 module to the Cresnet system. Data and power for the C2N-VEQ4 are provided via the connection. Refer to “Network Wiring” on page 7. C2N
Inhaltszusammenfassung zur Seite Nr. 11
Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control Industry Compliance As of the date of manufacture, the C2N-VEQ4 has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) these devices may not cause harmful interference, and (2) these devices must accept any interference r
Inhaltszusammenfassung zur Seite Nr. 12
Cresnet 4-Channel Digital Volume Control Crestron C2N-VEQ4 The required wire gauge should be chosen such that the resistance value is less than the value calculated in the resistance equation. Refer to the following table. Wire Gauge Values RESISTANCE WIRE GAUGE 4 16 6 18 10 20 15 22 13 Doubled CAT 5 8.7 Tripled CAT 5 NOTE: All Cresnet wiring must consist of two twisted pairs. One twisted pair is the +24V conductor and the GND conductor, and the other twisted pair is the Y conducto
Inhaltszusammenfassung zur Seite Nr. 13
Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control possible for the control system to recognize a network device via its serial number, which is stored in the device’s memory. This method does not require that any devices be disconnected from the network; Net IDs may be set with the entire Cresnet system intact. This method requires the use of the Crestron Viewport version 3.35 or later. Use the appropriate method to set the C2N-VEQ4 Net ID. Method A (Cresnet address-settable ID)
Inhaltszusammenfassung zur Seite Nr. 14
Cresnet 4-Channel Digital Volume Control Crestron C2N-VEQ4 “Set Net ID by TSID” Window 4. Click on the Search for Touch Settable Devices button. The system searches the network and lists all TSID-enabled devices found. The list is similar to the report produced by pressing F4 (Report Network Devices); the first eight digits of each line constitute the TSID number (hexadecimal form of the serial number). 5. As you enter either the serial number or TSID number of the device that require
Inhaltszusammenfassung zur Seite Nr. 15
Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control “Serial Number to TSID Conversion Tool” Window 3. Enter the serial number or TSID number as instructed; press the appropriate button to obtain the corresponding number. NOTE: Enter serial numbers, including spaces, exactly as they appear on the unit label. Alpha characters in serial numbers or TSID numbers may be entered in upper or lower case. Hardware Hookup Refer to the following hookup diagram. Complete the connections in a
Inhaltszusammenfassung zur Seite Nr. 16
Cresnet 4-Channel Digital Volume Control Crestron C2N-VEQ4 NOTE: An unbalanced input may use a balanced or unbalanced output. Likewise, a balanced input may use a balanced or unbalanced output. For connection details, refer to the following table and diagrams. Channels 1 and 2 are used as typical for all input and output channels. Audio Connections SIGNAL BALANCED BALANCED UNBALANCE UNBALANCE NAME AUDIO AUDIO D AUDIO D AUDIO INPUT OUTPUT INPUT OUTPUT + 1 + 1 + 1 + In 1 + Out - 1 - 1 - 1
Inhaltszusammenfassung zur Seite Nr. 17
Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control Programming Software Have a question or comment about Crestron software? Answers to frequently asked questions (FAQs) can be viewed in the Online Help section of the Crestron website. To post a question or view questions you have submitted to Crestron’s True Blue Support, log in at http://support.crestron.com./ First-time users will need to establish a user account. You can create a program that allows you to include the C2N-VEQ4
Inhaltszusammenfassung zur Seite Nr. 18
Cresnet 4-Channel Digital Volume Control Crestron C2N-VEQ4 Modules Directory. Crestron SystemBuilder accesses these tools behind the scenes, enabling you to easily create robust systems. Programming with SIMPL Windows NOTE: The following are acceptable file extensions for programs that include a C2N-VEQ4, developed for specific control system types: .smw projectname.smw (source file) .spz projectname.spz (compiled file for 2-series) .bin projectname.bin (compiled file for CNX generati
Inhaltszusammenfassung zur Seite Nr. 19
Crestron C2N-VEQ4 Cresnet 4-Channel Digital Volume Control Expanded PRO2 System Tree C2Net Device Slot in Configuration Manager To incorporate a C2N-VEQ4 into the system, drag the C2N-VEQ4 from the Cresnet Control Modules | Cresnet Audio Modules folder of the Device Library and drop it in System Views. The PRO2 system tree displays the C2N-VEQ4 in Slot 9, with a default Net ID of 12 as shown in the following illustration. NOTE: The first C2N-VEQ4 in a system is preset with a Net ID of
Inhaltszusammenfassung zur Seite Nr. 20
Cresnet 4-Channel Digital Volume Control Crestron C2N-VEQ4 NOTE: SIMPL Windows automatically changes Net ID values of a device added to a program if a duplicate device or a device with the same default Net ID already exists in the program. Always ensure that the hardware and software settings of the Net ID match. For Net ID hardware setting details, refer to “Identity Code” on page 8. C2N-VEQ4 Symbols in Programming Manager Programming Manager is where programmers “program” a Creston contr
