Inhaltszusammenfassung zur Seite Nr. 1
s
Program Library Karlsruhe
S79220-A0978-A-05-7637
Product Information
BRIDGE CS-L2
Var. V02.01 Issue: February, 1999
Descriptors
TELEPERM M , BRIDGE CS-L2 , UPGRADE , UPDATE
Summary
The present Product Information relates to the System Software Package:
Name Variant Product no. (MLFB)
BRIDGE CS-L2 V02.01 6DS2 510-0XX00-0XA0
BRIDGE CS-L2 V02.01 6DS2 510-0XX00-0XB1
upgrade/update V01.06
Description:
Ergänzende Systemdoku. ASx88/TM -
Ger
Inhaltszusammenfassung zur Seite Nr. 2
Product Information February, 1999 BRIDGE CS-L2 1 Scope The product information for the system software V02.00 remains valid. The following information represents a supplement. The delivery consists of: 6DS2 510-0XX00-0XA0 6DS2 510-0XX00-0XB1 (Upgrade/Update) BRIDGE CS-L2 Memory Card Diskette 3,5" with BRIDGE CS-L2 software Diskette 3,5" with tools for installation Diskette 3,5" with tools for installation Software contract and registration card Software contract Product Infor
Inhaltszusammenfassung zur Seite Nr. 3
Product Information February, 1999 BRIDGE CS-L2 2 Commissioning The Memory Card contains the entire system software for the Bridge (version V02.01) . To perform an upgrade or update from diskette, a BRIDGE CS-L2 memory card must be available. The upgrade procedure is performed offline with a PC or a programming device having a compatible MC interface (e.g. PG740). The update procedure is performed either from the IBS terminal (online) or from a programming device having a compat
Inhaltszusammenfassung zur Seite Nr. 4
Product Information February, 1999 BRIDGE CS-L2 2.2 Procedure for Upgrade to V02.01 with Programming Device PG740 Switch off the power supply of the BRIDGE CS-L2 before pulling the memory card! For the upgrade, insert the memory card into the MEM-CARD slot of the PG740. Now start the batch UPGRADE.BAT (if applicable, information on the memory card drive, default setting is E:): This batch file - creates a directory C:\UPGRADE.201 (for this, at least 1 MByte must be free on drive
Inhaltszusammenfassung zur Seite Nr. 5
Product Information February, 1999 BRIDGE CS-L2 2.3 Procedure for Update V01.05 to V01.06 2.3.1 Update by Commissioning Terminal You will find the files listed below in the directory A:\UPDATE.106 on the UPDATE diskette delivered to you. Copy these files to the directory ‘C:\ASBEDIEN’ on your Commissioning Terminal PC or into the current working directory (e.g. C:\TEMP is specified in ASBEDIEN.PIF). On the Commissioning Terminal PC connected to the BRIDGE CS-L2, start the program
Inhaltszusammenfassung zur Seite Nr. 6
Product Information February, 1999 BRIDGE CS-L2 2.3.2 Update by Programming Device PG740 Before starting the UPDATE activities (pulling the memory card), please ensure that a current backup of any files that are to be modified exists. This will allow the previous software version to be restored in the even of unforeseen circumstances. Switch off the BRIDGE CS-L2 before pulling the memory card! Copy the files listed under 2.3.1 from the update diskette into a new directory having
Inhaltszusammenfassung zur Seite Nr. 7
Product Information February, 1999 BRIDGE CS-L2 3.1 Removed Errors (already with V02.00) • F: Time synchronization A: Time telegrams were not always transmitted at high priority. In exceptional circumstances several time telegrams with different time data were transmitted shortly after one another. M: The throughput-time of time telegrams in the bridge was optimized. • F: Behavior when switch set to STOP A: In the STOP state, old telegrams were kept (e.g. several time teleg
Inhaltszusammenfassung zur Seite Nr. 8
Product Information February, 1999 BRIDGE CS-L2 Caution: When upgrading the bridge system software care must be taken that the bus coupling module TPM478 is version 5 or later, otherwise all error corrections will not be effective. 4 Extended Functions Installing the new M7 - CPU 486-3: From V02.00, the BRIDGE system software runs not only on the CPU 488-4, but also on the new CPU 486-3. The changes to the order configuration are described in detail in the PLT 112 catalo
Inhaltszusammenfassung zur Seite Nr. 9
Product Information February, 1999 BRIDGE CS-L2 4.1 Configuration of the BRIDGE CS-L2 with CPU 486-3 and IF964-DP As the CPU 488-4 is replaced by the CPU 486-3 and the CP5412-A1 is replaced by the IF964-DP interface module, there are the following alterations to the previous description of the standard configuration. EXM 478 with one IF964 CPU 486-3 Memory Card Power Supply System bus DC 24 V PROFIBUS-TM Service and Diagnostic Process control monitoring Slot Module Module
Inhaltszusammenfassung zur Seite Nr. 10
Product Information February, 1999 BRIDGE CS-L2 4.2 Instructions on installing the CPU 486-3 • The hardware version of the CPU 486-3 must be at least 2. Earlier versions can cause serious errors in the functions that use an interface module. • When using the TPM 478 with a CPU 486-3, the CPU BIOS must be at least version V2.07. This is guaranteed if hardware version 2 of the CPU 486-3 is used. • When installing the new CPU 486-3 modules, the red INTF LED can illuminate for se
Inhaltszusammenfassung zur Seite Nr. 11
Product Information February, 1999 BRIDGE CS-L2 5 Limited operating performance No safety-relevant faults are currently known; the known faults are assigned to fault class 3 and lower. • When using the load RAM function of PROGRAF AS+ by means of BRIDGE CS-L2 to an AS x88/TM, the bus load setting must be limited to a maximum of 10 %. • The Bridge buffers transactions that cannot be passed on directly to the receiver. Once the connection is reestablished, the backlog of telegram
Inhaltszusammenfassung zur Seite Nr. 12
Product Information February, 1999 BRIDGE CS-L2 6 Configuration of the bus connections The parameters for the BRIDGE CS-L2 are set in the configuration files BR_SYS.INI, DOS_CONF.DAT (or L2AMPRO.INI) and SYS_PAR.INI . Subsequent parameters for BRIDGE CS-L2 should be set individually. In doing this you should ensure compatibility with the other bus participants. DOS_CONF.DAT BR_SYS.INI Remark resp. L2AMPRO.INI station address TA l2_ts=xx [dez] BATA=yyxx [hex] yy = BA
Inhaltszusammenfassung zur Seite Nr. 13
Product Information February, 1999 BRIDGE CS-L2 6.1 Parameter of configuration file BR_SYS.INI Parameter ADR=xxxx Address of the Dual-Port-RAM of the TPM 478 C600 = standard system setting (hexadecimal) Parameter DPR=xx Address of the register of the TPM 478 C8 = standard system setting (hexadecimal) Parameter RANGE=xx Address range of all PROFIBUS-TM stations, which are coupled over the BRIDGE CS-L2 Permissible range: 1-20 (hexadecimal) Standard system setting: 20 (he
Inhaltszusammenfassung zur Seite Nr. 14
Product Information February, 1999 BRIDGE CS-L2 6.2 Parameter of configuration file DOS_CONF.DAT for CP5412-A1 The configuration file DOS_CONF.DAT includes the PROFIBUS-TM bus parameters. A specification of slot coordinates is not necessary. Bus parameters: Parameter l2_ts = Station No. on PROFIBUS-TM (decimal representation) Default setting: 32 Must be identical to the station address in BATA from BR_SYS.INI. If different addresses are entered, the parameter 'l2_ts
Inhaltszusammenfassung zur Seite Nr. 15
Product Information February, 1999 BRIDGE CS-L2 Example of a configuration file DOS_CONF.DAT: ___________________________________________________ # FILE FOR INSTALLING TF/IHI DRIVER # INSTTOOL VERSION = V 2.20 02.11.93 numboards = 1 boardtyp = 5412 SCP_device = CP_L2_1: l2_hsa = l2_ts = l2_physical_layer = 0 l2_lock_sap = NONE num_channel = 4 numproc = 2,5,5,0 channel_name = ADM,IHI,FLC,SCP channel_type = SCP,IHI,IHI,SCP element_size = 384 numhostbuffer = 2,75,75,2
Inhaltszusammenfassung zur Seite Nr. 16
Product Information February, 1999 BRIDGE CS-L2 The parameter assignments 'int_vector=12' and 'dpram_adr=0xD0000', with which the interrupt and DPRAM address range are set, agree with the default settings of the bridges and the DIP switches on the interface module CP5412-A1 which are already factory-set when delivered. Caution: If the L2AMPRO.INI configuration file is also saved on the memory card, this configuration takes precedence, i.e. a parameter file DOS_CONF.DAT existing in
Inhaltszusammenfassung zur Seite Nr. 17
Product Information February, 1999 BRIDGE CS-L2 according to the following equation and entered: l2_ttr = 9000 * [number of active PROFIBUS-TM stations]. Note: The factor 9000 in the equation only applies to a baud rate of 1.5 MBaud. All bus parameters are matched to a transmission rate of 1.5 MBaud. Optimization requires detailed knowledge of the PROFIBUS standard, Part 1, DIN 19245. Selection of a different transmission rate is illegal, and may result in faulty functioni
Inhaltszusammenfassung zur Seite Nr. 18
Product Information February, 1999 BRIDGE CS-L2 6.4 Parameter of configuration file SYS_PAR.INI The configuration file SYS_PAR.INI includes the parameter for inverting of the DIO- In/Outputs. If the file SYS_PAR.INI is not present, the operation system uses the default settings from file SYS_PAR.DEF. Parameter DIO_MASKE_EIN=xxx 000: Inputs not negated 255: Inputs negated Parameter DIO_MASKE_AUS=xxx 000: Outputs not negated 255: Outputs negated _______________________
Inhaltszusammenfassung zur Seite Nr. 19
Product Information February, 1999 BRIDGE CS-L2 7 Connector Pin Assignment IF961-DIO Following I & C Signals are available on IF961-DIO module: Function Assignment of the Outputs Output Pin Root Signalling output Use Remark 0V DO 0 DO 1 10 13 Common I & C signal Cabinet lamp max. 100 mA DO 2 DO 3 DO 4 DO 5 DO 6 DO 7 Function Assignment of the Inputs Input Pin Root Signalling input Use Remark +24V DI 0
Inhaltszusammenfassung zur Seite Nr. 20
Product Information February, 1999 BRIDGE CS-L2 8 Status display and error messages • The lamp test (all LEDs on) is not activated when switching on the network, but only with master-reset and soft-reset. • If the memory card is pulled during operation, after one minute, the bridge functionality can no longer be guaranteed. This is signaled by a flashing STOP LED and the LED USR1. • If the BRIDGE CS-L2 recognizes an error in the bus coupling TPM478, the bus coupling is autom
