Inhaltszusammenfassung zur Seite Nr. 1
SI-744
IN-WALL SURROUND SPEAKER
O w n e r ’ s M a n u a l
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Introduction Congratulations on your purchase of the RBH Sound SI-744 In-wall Surround speaker! Your speaker is the result of many years of research and development dedicated to producing high quality products for home audio and audio/video systems. This manual contains features, setup recommendations and specifications for RBH Sound SI-744 In-wall Surround speaker. It is recommended you thoroughly read through the material contained in this manual before installing or connecting your speake
Inhaltszusammenfassung zur Seite Nr. 4
Speaker Placement (continued) Front Main Speakers As a starting point, place your left and right speakers at least 7-feet apart from each other. The distance from the listening position to each speaker should be close to the distance that separates the two main speakers. Center Channel Speaker The Center Channel Speaker should be placed between both left and right main speakers. Often this positioning dictates placing the speaker either directly above or below a television monitor. Since s
Inhaltszusammenfassung zur Seite Nr. 5
Speaker Placement (continued) It is important for the SI-744 speaker to be positioned correctly, if not placed properly there will be a great reduction in imaging, sound staging and overall performance of the speaker. Refer to this illustration for position of the right and left speakers. The top tweeter should aim towards the front of the theater. Left Speaker Right Speaker Pre-wiring the Speaker 1. Unpack the speaker cabinet from the shipping box. 2. Run the speaker wires from th
Inhaltszusammenfassung zur Seite Nr. 6
Pre-wiring the Speaker (continued) Terminal Cup Amplifier/Receiver NOTE: Follow this diagram for dual mode operation. This example uses the left channel. Connect the left surround channel output from the amplifier to the left surround input of the terminal cup. Connect the surround back output from the amplifier to the rear Terminal Cup input of the terminal cup. Repeat for the right channel. Left Surround Left Left Rear Surround SI-744 Baffle Back View SI-744 Enclosure Front View
Inhaltszusammenfassung zur Seite Nr. 7
Pre-wiring the Speaker (continued) Amplifier/Receiver Terminal Cup NOTE: Follow this diagram for single mode operation, the example uses the left channel. Connect the left surround channel output from the amplifier to either set on inputs at the terminal cup. Be sure to untape and flip the switch on the crossover to single mode operation (see illustration on page 3). Repeat for the right speaker. Terminal Cup Left Surround Left Left Rear Surround SI-744 Baffle Back View SI-744 Enclos
Inhaltszusammenfassung zur Seite Nr. 8
Installing the Speaker 1. Determine where each speaker cabinet will need Left Surround to be installed. 2. If the cabinet is installed in a vertical position, the terminal cup will need to be on the top (see figure 1). 3. Position and brace the speaker cabinet in- between two studs by using a couple of screws to hold the speaker in place Left Rear (see figure 2). Figure 1 NOTE: The front of the cabinet should be flush with the front of the studs. 4. Using the included wood screws, se
Inhaltszusammenfassung zur Seite Nr. 9
Specifications Model: SI-744 System Type: In-wall Surround Speaker Frequency Response: 70Hz-20kHz ±3dB Sensitivity: 88/91dB (2.83V @ 1 Meter) Recommended Power: 75-150 Watts Woofers: Four 4” (102mm) Aluminum Cone Tweeters: Two 1” (25mm) Silk Dome Crossover Frequencies: 2,700Hz Crossover Slope: 12dB/Octave Impedance: 4 Ohms Combined, 8 Ohms per Channel Cabinet Material: Medium Density Fiberboard (MDF) Cabinet Finish: Black Baffle and Grille: Baffle Black; Grille Black or White. Enclosur
Inhaltszusammenfassung zur Seite Nr. 10
Warranty Your RBH Sound SI-744 in-wall surround speaker is covered by a limited warranty against defects in materials and workmanship for a period of 5 (five) years from the original date of purchase. This warranty is provided by the authorized RBH Sound dealer where the speaker was purchased. Warranty repair will be performed only when your purchase receipt is presented as proof of ownership and date of purchase. Defective parts will be repaired or replaced without charge by your dealer’s
Inhaltszusammenfassung zur Seite Nr. 11
Inhaltszusammenfassung zur Seite Nr. 12
TM Redefining The Way You Experience Sound. 382 Marshall Way, Layton, Utah • USA • 84041 Toll Free: (800) 543-2205 • Fax: (801) 543-3300 www.rbhsound.com It is RBH Sound policy to continuously incorporate improvements into products; all specifications are subject to change without notice. Copyright 2010 RBH Sound. All Rights Reserved. ©
