Inhaltszusammenfassung zur Seite Nr. 1
HRS150
HIGH RESOLUTION
POWERED SUBWOOFER
OWNER’S MANUAL
INPUT/OUTPUT STANDARD SETTINGS
SUBSONIC FILTER
POWER SUB BYPASSED
FILTER BYPASS
FLAT
SUBSONIC FILTER 15Hz
BYPASS FILTER SELECT ( 5.1)
FILTER IN LFE GAIN LFE GAIN
FILTER BYPASS
FULL RANGE
INPUT SENSITIVITY
VARIABLE
FILTER SELECT
110Hz ELIPTICAL
POLARITY
0dB NORMAL
LFE GAIN +
10dB
SUB SAT
80Hz
INPUT SENSITIVITY
CROSSOVER CONTROLS
0°
POLARITY
180°
OFF NORMAL
LEFT
(MONO)
IN
SUB SAT OUT
THX PM3 SETTINGS
80Hz
SUBSONIC FILTER
55Hz 110
Inhaltszusammenfassung zur Seite Nr. 2
9. Power Sources — This Mackie product should be connected to a power supply only of the type described in these operation instructions or as marked CAUTION AVIS on this Mackie product. RISK OF ELECTRIC SHOCK DO NOT OPEN 10. Power Cord Protection — Power supply cords should be routed so that RISQUE DE CHOC ELECTRIQUE they are not likely to be walked upon or pinched by items placed upon or NE PAS OUVRIR against them, paying particular attention to cords at plugs, convenience CAUTION: TO REDUC
Inhaltszusammenfassung zur Seite Nr. 3
Lend Me Your Ears Exposure to extremely high noise According to OSHA, any exposure in excess of levels may cause permanent hearing these permissible limits could result in some hear- loss. Individuals vary considerably in ing loss. To ensure against potentially dangerous susceptibility to noise-induced hear- exposure to high sound-pressure levels, it is recom- ing loss, but nearly everyone will lose mended that all persons exposed to equipment some hearing if exposed to sufficiently capable of p
Inhaltszusammenfassung zur Seite Nr. 4
For stereo and surround sound applications: QUICK START 4. Set the POWER switch on the rear We realize that you can’t ON position. The red POWER panel to the wait to hook up your new LED will turn on. Mackie Designs HRS150 5. Turn on the power to the other components High Resolution Powered in the system. Subwoofer and try it out. 6. Start your signal source (tape deck, CD, DAW, Nevertheless, please take the time to read this or whatever), but leave the master volume page NOW, and the rest can
Inhaltszusammenfassung zur Seite Nr. 5
INPUT/OUTPUT POWER SUB BYPASSED FLAT SUBSONIC FILTER 15Hz FILTER IN FILTER BYPASS FULL RANGE VARIABLE THX PM3 SETTINGS FILTER SELECT 110Hz ELIPTICAL SUBSONIC FILTER 0dB LFE GAIN + 10dB FILTER BYPASS INPUT SENSITIVITY FILTER SELECT (N/A) 0° LFE GAIN POLARITY 180° OFF NORMAL INPUT SENSITIVITY POLARITY LEFT (MONO) NORMAL IN OUT SUB SAT 80Hz SUB SAT 80Hz CROSSOVER CONTROLS 55Hz 110Hz CROSSOVER L L IN OUT R R SUB SAT ON 80Hz POWER 55Hz 110Hz CROSSOVER IN OUT RIGHT SLAVE/MASTER SLAVE MASTER IN O
Inhaltszusammenfassung zur Seite Nr. 6
PLACEMENT Corner or Center Placement AN IMPORTANT NOTE ON HRS150 BASS Placing the subwoofer in a corner (corner RESPONSE AND YOUR loading) excites the most room modes in the CONTROL ROOM OR room, which tends to smooth the individual LISTENING ROOM peaks and dips caused by each standing wave. You’ve heard it before. “Low-frequencies are Moving the subwoofer outward from the corner non-directional, so it doesn’t matter where you along the wall results in fewer standing waves, place the subwoofer.”
Inhaltszusammenfassung zur Seite Nr. 7
Play music with a good strong bass line and • Save the shipping box! You may need it crawl on the floor on your hands and knees until someday, and you don’t want to have to pay you find a spot where the bass sounds the best, for another one. with a smooth, tight response. Your ears need • Save your sales receipt in a safe place. to be at the same height that the subwoofer’s • Also record the HRS150 serial number in the driver will be when it is sitting on the floor. If space provided on the insi
Inhaltszusammenfassung zur Seite Nr. 8
REAR PANEL DESCRIPTION This is where you connect your signal inputs FILTER SELECT and outputs to the subwoofer, and make adjust- VA VAR RI IA AB BL LE E ments to the crossover, filters, and input FILTER SELECT 1 11 10 0H Hz EL z ELL LIP IPT TI IC CA AL L sensitivity. This switch selects either the built-in 4th-order For THX applications, the 24 dB/octave Linkwitz-Riley variable crossover rear panel switches and or the 7th-order 42 dB/octave 110 Hz elliptical controls should be set to the low-pa
Inhaltszusammenfassung zur Seite Nr. 9
POLARITY 0° POLARITY 180° THX = 0˚ This switch reverses the polarity of the sig- nal going to the subwoofer amplifier by 180º. INPUT/OUTPUT It has no effect on the signal at the LEFT and RIGHT OUT or the MASTER OUT. POWER SUB BYPASSED There is no right or wrong setting for this FLAT THX PM3 SETTINGS switch. Listen to the overall blend of the SUBSONIC FILTER 15Hz SUBSONIC FILTER subwoofer with the rest of the system, and select FILTER IN FILTER BYPASS FULL RANGE FILTER BYPASS the switch positio
Inhaltszusammenfassung zur Seite Nr. 10
Frequencies below the crossover frequency across the tip/sleeve when the internal relay is are sent to the subwoofer, and frequencies open, and a maximum 1 amp of current when above the crossover frequency are sent to the the relay is closed. LEFT and RIGHT OUTputs, which are con- CAUTION: There is an in- nected to the main/satellite speakers. ternal 1A fuse to protect the Set the crossover frequency to the lowest REMOTE INDICATOR circuit. frequency response rating of the main/satellite Exceedin
Inhaltszusammenfassung zur Seite Nr. 11
POWER Use this switch to turn the HRS150 on and off. The subwoofer is muted for about three seconds after the HRS150 is turned on while the power supply and internal circuitry stabi- lize. The auto on/off circuit is disabled when the POWER switch is off. MAINS INPUT Connect the power cord to this IEC socket, and plug the other end into your AC outlet. Make sure the outlet is properly configured for the voltage rating of your model. HOOKUP DIAGRAM Left Main/Satellite Right Main/Satellite Power
Inhaltszusammenfassung zur Seite Nr. 12
PROTECTION CIRCUITS CONNECTIONS There are several protection mechanisms Input and Output Signal Wiring designed into the HRS150 to safeguard the You should use high-quality, shielded cable loudspeaker and amplifier from inadvertent to connect the signal source to the LEFT and damage. RIGHT IN and OUT jacks on the HRS150. • Foil shielded cables, such as Belden 8451, Peak Limiter 8761, or 9501 are commonly used for A peak limiter is located at the input to the studio wiring. power amplifier sect
Inhaltszusammenfassung zur Seite Nr. 13
SERVICE INFO Details concerning Warranty Service are Bad Sound spelled out on the Warranty Card included with • Is the input connector plugged completely your subwoofer (if it’s missing, let us know and into the jack? we’ll rush one to you). • Is it loud and distorted? Reduce the signal If you think your subwoofer has a problem, level at the mixer. please do everything you can to confirm it before • If possible, listen to the signal source with calling for service, including reading through head
Inhaltszusammenfassung zur Seite Nr. 14
Repair Service for the U.S. versions of the HRS150 7. Ship the subwoofer to us. We suggest is available only from our factory service center insurance for all forms of cartage. Ship to located in sunny Woodinville, Washington. Ser- this address: vice outside the United States can be obtained through local dealers or distributors. Mackie Designs If your HRS150 needs service, follow SERVICE DEPARTMENT these instructions: 16220 Wood-Red Road NE 1. Review the preceding troubleshooting Woodinville, W
Inhaltszusammenfassung zur Seite Nr. 15
TECHNICAL INFORMATION HRS150 Block Diagram 15 CROSSOVER FREQ 2 A LEFT/MONO 1 2 B 1 LEFT/MONO OUT LINE INPUT 3 CTL LINE OUTPUT 3 55Hz-110Hz 24 dB/OCT LINKWITZ-RILEY CENTER POSITION (80Hz) FOR THX CROSSOVER FREQ 2 RIGHT A 1 2 RIGHT B OUT 1 LINE INPUT 3 CTL LINE OUTPUT 3 FILTER FILTER SELECT BYPASS 55Hz-110Hz FILTER IN +100V +90V 110Hz LFE +15V 15Hz SUBSONIC FULL RANGE ELLIPTICAL GAIN 18 dB/OCT FILTER (THX) INPUT POWER BUTTERWORTH 0 dB (THX) FLAT (THX) SENSITIVITY POLARITY AMPLIFIER LPF SUBWOOFER
Inhaltszusammenfassung zur Seite Nr. 16
Specifications Transducers Acoustic Section Low-frequency driver Acoustic Frequency Response: 20 Hz to 150 Hz, ±1.5 dB Diameter: 15 in/381 mm –3 dB points: 19 Hz, 250 Hz Sensitivity: 96 dB SPL (1 W, 1 M) Maximum SPL: 122 dB @ 1 meter Nominal Impedance: 8 ohms Residual Noise: < 8 dBA SPL Voice Coil Diameter: Power Amplifier Section 4 in/100 mm Rated Power Output (1% THD at 100 Hz): Power Handling (Long Term/Program): 950 watts rms into rated 8Ω load 400/1000 watts Peak Power Output (100 Hz sine,
Inhaltszusammenfassung zur Seite Nr. 17
Graphs HRS150 Crossover Filter Response +10 +8 +6 +4 +2 -0 -2 -4 -6 -8 -10 -12 -14 dBr -16 -18 -20 -22 -24 -26 -28 -30 -32 55Hz -34 80Hz -36 110Hz -38 -40 10 20 50 100 200 500 1k 2k 5k 10k 20k Hz HRS150 Elliptical Filter Response +10 +8 +6 +4 +2 -0 -2 -4 -6 -8 -10 -12 -14 dBr -16 -18 -20 -22 -24 -26 -28 -30 -32 -34 -36 -38 -40 20 50 100 200 500 1k 2k 5k 10k 20k Hz HRS150 Free-Field Frequency Response (THX pm3 setting) +10 +8 +6 +4 +2 +0 -2 -4 -6 -8 -10 -12 -14 dBr -16 -18 -20 -22 -24 -26 -28 -30
Inhaltszusammenfassung zur Seite Nr. 18
COLOPHON The text is a compilation based on input from a number of sources including Cam Jones, Terry Wetherbee, Marcelo Vercelli, and Keith Olsen. Dave Franzwa and Jayney Wallick pro- duced this manual using the following tools: ® Initially written in Microsoft Word 98 for the Macintosh, the text was imported into ® Adobe PageMaker 6.5. Illustrations were pro- ® duced in Adobe Illustrator 9.0. Most of the ® work was done on two Power Macintosh G4 computers with Mac OS 9.1 installed. These machi
Inhaltszusammenfassung zur Seite Nr. 19
HRS150 LIMITED WARRANTY Please keep your sales receipt in a safe place. A. Mackie warrants all materials, workmanship and G. Any Mackie product deemed eligible for repair or proper operation of this product for a period of three replacement under the terms of this warranty will be years from the original date of purchase. If any de- repaired or replaced within thirty days of receipt by fects are found in the materials or workmanship or if Mackie. Mackie may use refurbished parts for repair the p
Inhaltszusammenfassung zur Seite Nr. 20
Mackie Designs Inc. 16220 Wood-Red Road NE Woodinville, WA 98071 USA US and Canada: 800.898.3211 Europe, Asia, Central and South America: 425.487.4333 Middle East and Africa: 31.20.654.4000 Fax: 425.487.4337 www.mackie.com E-mail: sales@mackie.com
