Inhaltszusammenfassung zur Seite Nr. 1
Programming
Washer-Extractors
Cabinet Freestanding
WE-8 Computer
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 9001889R7
www.comlaundry.com July 2011
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
WARNING Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and carefulness are factors which cannot be built into these washers. These factors MUST BE supplied
Inhaltszusammenfassung zur Seite Nr. 4
Introduction......................................................................................... 3 Table of Model Identification ............................................................................. 3 Programming ...................................................................................... 4 Contents Setup of the Machine ............................................................................ 4 Version of Control ........................................................
Inhaltszusammenfassung zur Seite Nr. 5
Introduction Model Identification Information in this manual is applicable to these models: HX018PVQM7 HX18PVXU6 SX18PVQU6 UX018PVQM7 UX18PVPA7 UX18PVXA6 HX018PVXM7 SX018PVPA7 SX18PVXM6 UX018PVXA7 UX18PVPU6 UX18PVXA7 HX18PVQM6 SX018PVQM7 SX18PVXM7 UX018PVXM7 UX18PVQA6 UX18PVXM6 HX18PVQM7 SX018PVXM7 SX18PVXU6 UX18PVNA6 UX18PVQA7 UX18PVXM7 18 HX18PVQU6 SX18PVPA7 UX018PVNA7 UX18PVNA7 UX18PVQM6 UX18PVXU6 HX18PVXM6 SX18PVQM6 UX018PVPA7 UX18PVNU6 UX18PVQM7 HX18PVXM7 SX18PVQM7 UX018PVQA7 UX18PVPA6 UX1
Inhaltszusammenfassung zur Seite Nr. 6
Programming Setup of the Machine Turn key from Run to Program RUN PROGRAM Program Cycle 00 To go to the main setup of the machine, press “Auxiliary”, “2”, “9”. System Program _X18PV To change the machine type, press the “Advance” button. The following types are possible: System Program _X25PV _X18PV _X40PV _X135PV _X25PV _X55PV _X165PV _X33PV _X75PV _X200PV Press the “Advance” button until the right type of Units: English machine is selected. Press the “Enter” button. Select the desired units
Inhaltszusammenfassung zur Seite Nr. 7
Programming Press the “Enter” button to select options. Options : Press the “Aux Fill” button for auxiliary fill option or press “Enter” for heating. Options : Aux Fill If heating is selected, the user can fill in the kW of the electrical heating (example: 9 kW). Heating : 6 kW Press “0”, “9”. Heating : 9 kW Press “Enter” to select advance mode in run mode yes or no. Advance : Yes Press “Advance” to change between yes and no. Advance : No 9001889 © Copyright, Alliance Laundry Systems LLC – DO
Inhaltszusammenfassung zur Seite Nr. 8
Programming Press “Enter” to set the hysteresis level (level at which water drops before it senses it must refill). Level : hyst 2" If English is selected for units, this value will be in inches. If Metric is selected for units, this value will be in cm. Select between 1 to 9 cm or inches. Press “Enter” to select the temperature hysteresis (level at which temperature drops before machine Temp : hyst 3°F senses it must reheat). If English is selected for units, this value will be in °F. If
Inhaltszusammenfassung zur Seite Nr. 9
Programming NOTE: If chemical hold is off, then supplies 4 Version of Control through 9 are controlled exactly like supplies 1 To determine control version, apply power to machine. through 3. A switch closure/opening between pins 1 Control will display version of control (i.e., 1.15). and 4 of the COIN header on the output board will have no effect. Language on Display (Version 1.15 and later ONLY) Program Storing Mode To set a different language on the WE-8 display: The WE-8 control is ca
Inhaltszusammenfassung zur Seite Nr. 10
Programming Example: Warm Low (time limit 5 minutes Explanation of the Step Functions 30 seconds) Fill: Choose between 4 water inlet configurations and 3 water levels. Step XX Cycle XX Water Inlet Configurations: Warm Cold: Only opens the cold water valve. Hot: Only opens the hot water valve. Warm: Opens the cold and hot water valves. Aux Fill: Opens an auxiliary water valve Step XX Cycle XX Warm Low if installed. Water Levels: Low: Low water level. Med: Medium water level. Step XX Cycle XX
Inhaltszusammenfassung zur Seite Nr. 11
Programming It is possible to more accurately control the Step XX Cycle XX temperature of water coming in to the machine during 95°F Low a fill step. This does not apply to “Aux Fill” step. The control will mix the hot and cold water inlet to the temperature programmed in the fill function. To fill in the temperature, select the water inlet type and the water level. Press the “Heat” button and the control Step XX Cycle XX will ask the temperature. In this way the water inlet 0 min type s
Inhaltszusammenfassung zur Seite Nr. 12
Programming Wash: Supply: Choose between 7 different preset wash actions. Choose between 9 different supplies. Supply 1: Turns on the water valve in compartment Action Stop Time G-force A of the supply box. Time (sec) (sec) Supply 2: Turns on the water valve in compartment Wash 1 18 3 0.5 B of the supply box. Wash 2 3 27 0.5 Supply 3: Turns on the water valve in compartment Wash 3 0 0 0 C of the supply box. Wash 4 10 20 0.5 Supply 4: Activates supply pump 1. Wash 5* 18 3 0.5 Supply 5: Activa
Inhaltszusammenfassung zur Seite Nr. 13
Programming Chemical Hold Feature Enter time in minutes Chemical supply injection can be paused. Refer to and press “Enter” Setup of Chemical Hold Feature. (example: 5 min). Step XX Cycle XX Wash 5 Thermal Cool-Down 1 hours 05 min Immediately after a heat step, a temperature-controlled thermal cool-down may be programmed to prevent fiber shock from sudden cool-down. Step XX Cycle XX The “Heat” button is number 5. Wash Example: Heat up to 140°F with the time limit of 45 minutes. Thermal Coo
Inhaltszusammenfassung zur Seite Nr. 14
Programming Soak: Example: Soak time of 2 hours with 32°F. Button 7 is the “Soak” button. By pressing button 7, “Soak” will appear on the display. Press “Enter” to fill in the soak time. Step XX Cycle XX Soak Example: Soak for 2 hours. Step XX Cycle XX Step XX Cycle XX Soak 0°F Use the key pad to fill in the soak temperature (example: 32°F). Step XX Cycle XX 0 hours Step XX Cycle XX 32°F Use the key pad to fill in the hours of the soak time (example: 2 hours). Step XX Cycle XX Step XX Cycle
Inhaltszusammenfassung zur Seite Nr. 15
Programming Spin: Drain: Choose between 4 preset spin speeds. This function drains the water. If you have 2 drains, select which drain has to be 18-75 100/135 165 200 opened. Models Models Models Models Spin 1 500 500 500 RPM Step XX Cycle XX Drain Spin 2 650 650 650 RPM Spin 3 800 800 750 Select Drain 1 or 2. If you only have 1 drain, RPM you can only select 1. Spin 4 1000 80 750 Step XX Cycle XX Drain 2 RPM “Spin” is button 9. Step XX Cycle XX 0 min Step XX Cycle XX Spin Enter the drain time
Inhaltszusammenfassung zur Seite Nr. 16
Programming Example Making a New Program Program Cycle 00 Program 51 Step 1: Fill warm water to low level (5 minutes 30 seconds time limit) Step 2: Supply 1 and 5 for 20 seconds Program Cycle 51 Step 3: Heat up to 140°F (45 minutes time limit) Step 4: Wash action 4 for 8 minutes 00 seconds Step 5: Drain 1 for 1 minutes 25 seconds Step 6: Spin 3 for 8 minutes 30 seconds To program or edit cycles turn the key into the Add Cycle 51 Program Mode. “Program Cycle xx” will be shown on the display.
Inhaltszusammenfassung zur Seite Nr. 17
Programming Step 01 Cycle 51 Step 02 Cycle 51 Warm Supply Step 01 Cycle 51 Step 02 Cycle 51 Warm Low Supply 1 5 Step 01 Cycle 51 Step 02 Cycle 51 0 min 0 min Step 01 Cycle 51 Step 02 Cycle 51 5 min 30 sec 0 min 20 sec End Cycle 51 End Cycle 51 Step 02 Cycle 51 Step 03 Cycle 51 9001889 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 15
Inhaltszusammenfassung zur Seite Nr. 18
Programming Step 03 Cycle 51 Step 04 Cycle 51 Heat Wash 4 10/20 Step 03 Cycle 51 Step 04 Cycle 51 0°F 0 min Step 03 Cycle 51 Step 04 Cycle 51 140°F 8 min 00 sec Step 03 Cycle 51 End Cycle 51 0 hours Step 03 Cycle 51 Step 05 Cycle 51 0 hours 45 min End Cycle 51 Step 05 Cycle 51 Drain 1 Step 04 Cycle 51 Step 05 Cycle 51 0 min Step 04 Cycle 51 Step 05 Cycle 51 Wash 1 min 25 sec © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9001889 16
Inhaltszusammenfassung zur Seite Nr. 19
Programming End Cycle 51 Enter to save ? Step 06 Cycle 51 Program Cycle 51 Step 06 Cycle 51 Spin 1 Step 06 Cycle 51 Spin 3 Step 06 Cycle 51 0 min Step 06 Cycle 51 8 min 30 sec End Cycle 51 9001889 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 17
Inhaltszusammenfassung zur Seite Nr. 20
Programming Edit a Cycle Program Cycle 00 Change a Complete Step To edit a cycle enter the cycle number (example: cycle 51). Program Cycle 51 Edit Cycle 51 Press the “Edit Cycle” button. Name Cycle 51: Press the “Enter” button to edit the cycle. Cycle 51 Step 01 Cycle 51 Press “Enter” to continue. Warm Low The first step of cycle 51 will display. Step 02 Cycle 51 Select the step being edited by using the “Advance” Wash 1 18/3 button to go to the next step or the “Previous” button to go to
