Inhaltszusammenfassung zur Seite Nr. 1
B7FH-2961-02EN-00
RX300 S2
���� ������ �
������������������������������������ � � �������� �
���������������������������������������� � � ��������
���������������������������������������������������������������
������������������������������������������� � ������������ ��������
PRIMERGY RX300 S2 Manuals
n
Manuals for this server can be accessed from the section below of the PRIMERGY Document & Tool CD (Disc 2).
[CD-ROM Drive] :\MANUAL\INDEX.PDF
Manuals can be displayed using Acrobat® Reader® or
Inhaltszusammenfassung zur Seite Nr. 2
Checking location before installing the server 4 For details on installing the rack, refer to the "Installation Remove the inner rail from the slide 3 Guide for the RACK" and the manual provided with the rail rack. Press down the lock in the center of the inner rail to remove. nConditions ������������������� ���������� When installing this server avoid the following areas. - Humid, dusty, or oily areas - Poorly ventilated areas ���������� ���������������� - Areas close to fire or other sourc
Inhaltszusammenfassung zur Seite Nr. 3
Attach the slide rail assemblies and Insert the server to fit into the rail as- 8 6 insert the rack nuts into the rack sembly inside the rack. holes. Insert the inner rail of the server to the grooves of the slide rail and slide the server towards the back Attach slide rails with washers. to install to into the rack. Insert latches of the rack nuts from inside of the rack bracket. ������� ������ ���� ����������� � ���������������������� � ����� ������������� Rails have lock. When pulling out
Inhaltszusammenfassung zur Seite Nr. 4
Turning on the power and setting hardware 6 Normally, hardware settings are not required to be changed from the default. However, in the following cases, start each utility and check/change hardware settings. "Chapter 8 Hardware Configuration / Utilities" ������������ lBIOS Setup utility Change the settings in the following cases: - When changing the drive to start the server - When installed/removed optional devices - When performing remote installation - Print the "Configuration Sheets" - "C
Inhaltszusammenfassung zur Seite Nr. 5
Installing the OS 7 This section explains the procedures to install the OS using ServerStart. For details about os installation procedures when not using ServerStart, refer to the "User's Guide". "Chapter 4 Manual OS Installation" ������������ Insert the ServerStart floppy disk Click [Start here to create a complete 1 10 supplied with this server, and click configuration file]. [Create]. The [Open ServerStart Configuration File] window appears. A network setup window for remote installation
Inhaltszusammenfassung zur Seite Nr. 6
Turning off the power and installing optional devices 8 Install optional devices to be installed after the OS installation, such as UPS device. "Chapter 7 Installing Internal Options" ������������ After optional devices are installed, set the BIOS Check that no medium is inserted in 1 setup utility or WebBIOS as required. the floppy disk drive or CD-ROM drive. For details about setting procedures, refer to the "User's Guide Chapter 8 Hardware Configuration/ Exit the operating system (OS).
Inhaltszusammenfassung zur Seite Nr. 7
lNon-durable components Depending on the environment and period of usage there Recycle 1 1 will be non-durable components that require replacement within the warranty period. Customers who have signed up When disposing of this server, contact an office listed in to hardware maintenance contract will be provided with re- the "Contact Information". placement parts free of charge and will have higher priority This server must be disposed of as industrial waste. for replacement. Customers not
Inhaltszusammenfassung zur Seite Nr. 8
Notes Data Backup To protect data stored in this device (including basic software and application software), perform backup and other necessary operations. Note that data protection is not guaranteed when repairs are performed. It is the customer's responsibility to maintain backup copies in advance. In case of data loss, Fujitsu assumes no liability for data maintenance or restoration and damages that occur as a result of the data loss for any reason, except for items covered under warranty.
