Inhaltszusammenfassung zur Seite Nr. 1
Cube
Network Camera
IP8130W/8131W
User’s Manual
IP8130W/8131W: 1MP • 802.11n WLAN • WPS
Rev. 1.0
Inhaltszusammenfassung zur Seite Nr. 2
VIVOTEK Table of Contents Oviewver ���������������������������������������������������������������������������������������������������������������������������������������� 4 Revision History �������������������������������������������������������������������������������������������������������������������������������������� 4 Read Before Use �����������������������������������������������������������������
Inhaltszusammenfassung zur Seite Nr. 3
VIVOTEK Local storage > Content management ����������������������������������������������������������������������������������������������������� 115 ����������������������������������������������������������������������������������������������������������������������������������������������������� Appendix 118 URL Commands for the Network Camera ������������������������������������������������������������������������������������������������ 118 Technical Specifications �����������������������
Inhaltszusammenfassung zur Seite Nr. 4
VIVOTEK Overview VIVOTEK IP8130/31/30W/31W are compact cube cameras designed for indoor surveillance � The elegant design makes it an ideal solution for offices, shops and homes. A built-in microphone further increases the level of surveillance by recording sound within a 6 meter radius. Moreover, the IP8131/31W are equipped with IR LEDs and IR-cut filter, providing clear video in completely dark environments. The IP8130/31/30W/31W support the industry-standard H.264 compression technology,
Inhaltszusammenfassung zur Seite Nr. 5
VIVOTEK Read Before Use The use of surveillance devices may be prohibited by law in your country� The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system� It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use� It is important to first verify that all contents received are complete according to the Package Contents listed below� Take note of the
Inhaltszusammenfassung zur Seite Nr. 6
WPS LED Definitions VIVOTEK Physical Description Front Panel IP8130W Status LED Lens Microphone MicroSD/SDHC/SDXC Card Slot IP8131W WPS button (wireless models) Lens Status LED IR LEDs Microphone Description Item LED status 1 Steady Red Powered on, during system boot, or indicating no network connection All LED off Powered off 2 Blinking Blue every 0�15 sec� Searching for WPS 3 Blinking Green every 1 sec� Network connected (wired or wireless) 4 Blinking Green and RED intermittently Upgrad
Inhaltszusammenfassung zur Seite Nr. 7
VIVOTEK Rear Panel The back panels are identical for all models. Antenna Connector (for wireless models) Reset Button Power Cord General I/O Socket Terminal Block Ethernet 10/100 RJ45 Socket 1 DI- 2 DI+ 3 Audio GND 4 Audio Out Audio out cable is user-supplied� User's Manual - 7
Inhaltszusammenfassung zur Seite Nr. 8
VIVOTEK Install Camera to Stand Attach the camera to stand and orient the shooting angle. If preferred, use the included screws to secure the the camera stand to a mounting surface� IMPORTANT: Record the MAC address before installing the camera� IP8130W 0002D10766AD 8 - User's Manual
Inhaltszusammenfassung zur Seite Nr. 9
VIVOTEK Digital Input Diagram Please refer to the following illustration for the connection method� Max. voltage: 40V 3.3V DI+ Digital input DI- DI-: Ground Connect a digital input device to the input pins of the camera� From the Applications > Digital Input page, you can let camera report the current signal status as High or Low to determine the signal’s Normal status during operation� User's Manual - 9
Inhaltszusammenfassung zur Seite Nr. 10
VIVOTEK Hardware Reset Reset Button The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation If � the system problems remain after reset, restore the factory settings and install again. Reset: Press and release the reset button� Wait for the Network Camera to reboot� Restore: Press and hold the recessed reset button until the status LED rapidly blinks� Note that all settings will be restore
Inhaltszusammenfassung zur Seite Nr. 11
PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Network Deployment LAN Connection 1. If you have external devices such as sensors and alarms, make connections from general I/O terminal block� 2 � Connect the camera to a switch via Ethernet cable or directly to a computer Ethernet � must be connected before power on � 3� Connect the supplied power cable from the camera to a power outlet� Non-PoE Switch Wireless configuration will be discussed later on page 19. User's Manual - 11
Inhaltszusammenfassung zur Seite Nr. 12
PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below� 1. Connect your Network Camera behind a router, the Internet environment is illustrated below. Regarding how to obtain your IP address, please refer to Software Installation on page 14 for details� IP address : 192.168.0.3 WAN (Wide Area Network ) Subnet mask : 255.255.255.0 Router IP address
Inhaltszusammenfassung zur Seite Nr. 13
VIVOTEK Configure the router, virtual server or firewall, so that the router can forward any data com- ing into a preconfigured port number to a network camera on the private network, and allow data from the camera to be transmitted to the outside of the network over the same path � From Forward to 122146 � �57�120:8000 192�168�2�10:80 122�14657 � 120:8001 � 192168 � 2 � 1 � 1:80 ��� ��� When properly configured, you can access a camera behind the router using the HTTP request as follows: h
Inhaltszusammenfassung zur Seite Nr. 14
VIVOTEK Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� IW2 1� Install IW2 under the Software Utility directory from the software CD � Installation Double-click the IW2 shortcut on your desktop to launch the program� Wizard 2 2� The program will conduct an analysis of your network environment� After your network environment is analyzed, please click Next to continue the program� 3� T
Inhaltszusammenfassung zur Seite Nr. 15
VIVOTEK Ready to Use 1� A browser session with the Network Camera should prompt as shown below� 2� You should be able to see live video from your camera� You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras� For its installation details, please refer to its related documents. User's Manual - 15
Inhaltszusammenfassung zur Seite Nr. 16
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN� If your network environment is not a LAN, follow these steps to access the Netwotk Camera: ® 1. Launch your web browser (e.g., Microsoft Internet Explorer or Mozilla Firefox)� 2. Enter the IP address of the Network
Inhaltszusammenfassung zur Seite Nr. 17
VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 77� ® ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX Controls for your browser � 1� Choose Tools > Internet Options > Security > Custom Level� ® 2 Look
Inhaltszusammenfassung zur Seite Nr. 18
VIVOTEK IMPORTANT: • Currently the Network Camera utilizes 32-bit ActiveX plugin� You CAN NOT open a management/view session with the camera using a 64-bit IE browser� • If you encounter this problem, try execute the Iexplore.exe program from C:\Windows\ SysWOW64� A 32-bit version of IE browser will be installed� • On Windows 7, the 32-bit explorer browser can be accessed from here: C:\Program Files (x86)\Internet Explorer\iexplore.exe Tips • The onscreen Java control can malfunction u
Inhaltszusammenfassung zur Seite Nr. 19
WPS VIVOTEK Wireless Connection: Using the WPS Button 1� Make sure your AP (Access Point) and Operating System support WPS (Wi-Fi Protected Setup) functions� WPS enables easy setup with compatible APs� 2. Disconnect your LAN cable, and connect the power cord. 3� Wait for 1 minute for the camera to boot up Press the WPS button for 1 second � � The front panel LED should blink blue� 4� Press and hold down the WPS button on your AP (some router/AP will have a virtual button on their manageme
Inhaltszusammenfassung zur Seite Nr. 20
VIVOTEK Wireless Connection: Manual Configuration 1. In addition to the use of WPS function, you can also use a wired connection to manually set up your wireless configuration. 2� Enter the Configuration > Wireless > WLAN page� Key in the same wireless settings as those on your router/AP (SSID, Encryption type, and Pre-shared key). 3. When done, click the Save button, disconnect the Ethernet cable and then reboot the camera (by disconnect and then connect the power cord)� The camera should
