Inhaltszusammenfassung zur Seite Nr. 1
ADSDUHOC, ADSDUHOS, ADSDUHOVRC, ADSDUHOVRS
®
SpeedDome Ultra Outdoor Housing Installation Guide
= Step Prevents IMPORTANT! This housing meets IP66/Nema 4 ratings
Before performing these steps, read additional
provided it is used with a properly installed ROENDC End
Water Intrusion.
information attached for important details and
Cap Assembly and one of the following mounts: RHOTR
warnings!
Over-the-Roof Mount, RHOSW Short Wall Mount, or
RHOLW Long Wall Mount.
Attach cable
Make connect
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT! Both the outdoor housing and dome x100 x10 x1 camera are shipped “terminated” for when they are installed at the end of a data cable. Should the cable Set the dome Attach bubble continue to another dome, “unterminate” the housing. 4 6 7 address. assembly. SW3 SW2 SW1 See information attached. The address range is from 001 to 255, except for Manchester, Place the desiccant bag in the pocket which is 01 to 64. located inside the housing and adjacent A to the blower/heater
Inhaltszusammenfassung zur Seite Nr. 3
® To the Installer SpeedDome Ultra This guide assumes that the outdoor mounting Outdoor Housing structure to which the housing is attached is in Installation Guide–Continuation place and that data and power cables have been pulled to the installation site. To install the outdoor mounting structure, see documents shipped with the structure. About the Product The outdoor housing has a sunshield cover and bubble that protect the SpeedDome Ultra dome camera. Tamperproof screws affix th
Inhaltszusammenfassung zur Seite Nr. 4
Cautions Warnings and Cautions Water leaks, even small ones, can Please review the following warnings and cautions increase humidity inside the outdoor before you begin installation or service. housing. To help eliminate humidity, follow all instructions explicitly and Warnings also the following cautions: WARNING! Always use proper lift and - DO NOT use over seals such as safety equipment for the location and RTV and silicone caulks. ! type of installation. Use the safety - En
Inhaltszusammenfassung zur Seite Nr. 5
O-ring (inside Preventing Condensation cover) Foam seal Damage, missing parts, or procedures (inside pipe) that most often allow water to enter the housing are as follows (refer to Sleeve (outside), figures opposite): Seal (inside end cap assembly) Missing O-ring on cover, or missing sleeve or seal on end cap assembly Missing Teflon tape around any housing pipe threads RTV or similar sealant covering an air path Exploded view Blower fans not turning Loose tamperproo
Inhaltszusammenfassung zur Seite Nr. 6
Connector Pin Assignments Cable Requirements GREEN CONNECTOR (POWER) Data Cable Pin Color Description The table below shows requirements for SensorNet, 1 Black 24Vac RS-422, and Manchester networks. For more information about communication protocols and 2 Red Common cable networks, see Communication Protocols and 3 White 24Vac Cable Networks, 8000-2573-19. BLACK CONNECTOR (DATA) Data cable requirements Manchester SensorNet RS-422 Manchester Pin Color* Designation 1-4 — Not us
Inhaltszusammenfassung zur Seite Nr. 7
On the circuit board: Housing Termination and Video Video Configuration UTP Termination Both the outdoor housing and dome Jumper camera are shipped “terminated” for when they are installed at the end of a data Video Extension cable. Should the cable continue to Cable BNC another dome, “unterminate” the housing using the following procedure. Video Config. IMPORTANT! Leave the dome camera set Jumpers to “terminated.” E2, E3 (Default = Pins 1 Unterminating the Outdoor Housin
Inhaltszusammenfassung zur Seite Nr. 8
4. On the circuit board is a mark (shown below). To reattach the board to the housing, match the mark to an identical mark on the base and snap the board in place. 5. Gently remove the dust cover. Note: Keep the cover and use it to protect contacts should the environmental PC board need to be removed from the housing. SPEEDDOME ULTRA OUTDOOR HOUSING 8200-0492-02, REV. C INSTALLATION GUIDE - CONTINUATION 8 of 12
Inhaltszusammenfassung zur Seite Nr. 9
3. Verify data is reaching the housing. Troubleshooting SENSORNET or RS-422: Press and hold switch SW2 on the environmental PC board and This section covers what to do when: observe the yellow (comm.) LED. The LED • Dome does not respond to commands should blink (SensorNet) or glow steadily (RS-422). • Fans do not turn • Picture is grainy or discolored To verify RS-422 connections at connector P1, press and hold data test switch SW1 on • Poor video environmental PC board. Check th
Inhaltszusammenfassung zur Seite Nr. 10
SensorNet Data Connections Blowers Do Not Turn Follow steps until the problem is corrected. See Pin Color Designation page 5 to order parts. 1-4 — Not used. 1. Determine if the dome camera is receiving 5 White/Orange SensorNet (unshielded) power. Look for evidence such as a picture on 6 White/Yellow SensorNet (unshielded) the video monitor or dome movement. 2. Detach the dome camera to access the 4. Check fans. Are they on? environmental PC board. - YES: Continue. Note: Power to
Inhaltszusammenfassung zur Seite Nr. 11
Ice Forms On Bubble Specifications Follow steps until the problem is corrected. See page 5 to order parts. Electrical (combined dome and housing) 1. Are blower/heater fans in the housing working? Input Voltage .............................. 24 to 30Vac, 50/60 Hz NEC Class 2 If not, see “Fans Do Not Turn” opposite. Certified Limited Power Source 2. Is the camera dome receiving power? Look for Design Tolerance ....................... 20 to 36Vac, 50/60 Hz evidence such as a picture
Inhaltszusammenfassung zur Seite Nr. 12
Other Declarations Declarations Thank you for using American Dynamics products. We support our products through an extensive and worldwide Regulatory Compliance network of dealers. The dealer, through whom you originally purchased this product, is your point of contact if you have a REG ID: SV SDUO need for service or support. Our dealers are fully empowered to provide the very best in customer service and support. Emissions ..............................47 CFR, Part 15, Class A Dea
